MICOROX® 1882 SEALER
- Chemical Family
- Epoxy & Epoxy Derivatives
MICOROX® 1882 SEALER is a 100% solids epoxy coating designed for application in corrosive environments. 1882 may be used as either a topcoat or a sealer. When used as a topcoat, this two-component epoxy enhances the chemical and abrasion resistant properties of MICOROX® FLOORING SYSTEMS while increasing cleanability. MICOROX 1882 SEALER offers superior protection for new and old surfaces when applied as a concrete floor sealer. MICOROX 1882 is U.S.D.A. approved for incidental food contact.
Product families
Applications
- Floor Coatings
Product Families
- Primers & Sealers
Other characteristics
- Brand
- MICOROX
- Features
Abrasion Resistant, Chemical Resistant, Corrosion Resistant, Good Penetration
- Product Type
2K (2 component) Coating, Epoxy Coating, Sealer, Solventless & High Solids Coating, Top Coat; 2K (2 component) Coating; Epoxy Coating; Sealer; Solventless & High Solids Coating; Top Coat
- Application Method
- Brush, Roller, Wipe
- Compatible Substrates & Surfaces
- Concrete
- Markets
- Building & Construction
- PACKAGING
MICOROX® 1882 SEALER is packaged in pre-proportioned units based on gallon quantities.
- Application
1882 SEALER is extremely easy to use. It may be installed by a Micor application crew, a local contractor, or plant personnel.; On concrete surfaces MICOROX 103 Primer makes an excellent primer. Apply the primer in a very thin, even film with no build up or puddling. Coat over the primer before it has completely cured.; Mix 1882 SEALER by combining one pre- measured container of resin with one pre measured container of hardener. Mix thoroughly with a drill-stirrer. Premix components to redisperse any settled fillers or pigments. Materials should be mixed for approximately two minutes. No induction time is required. The material may be applied immediately.; Apply the material by squeegee, roller, or brush. Apply in a thin, even film of 10-20 mils thickness If a second coat is being applied, Timing is critical. Allow the first coat to harden. If the first coat completely cures, bonding additional coats can be difficult and may require special preparation techniques. Hardening may take place in 3-5 hours at 77° F.
- Precaution
Contact with liquids Part A and B can cause irritation. Wear protective clothing. Cover hands with protective cream and/or gloves. Wear chemical splash goggles. Use only with adequate ventilation.
- Availability
Available in Clear and 14 basic colors. Custom colors upon request.
- Technology
- Ready-to-Use Products
- Application Methods
- Brush
- Roller
- Wipe
- Hardening and Cure
1882 SEALER hardens for foot traffic in 12 hours at 77°F Complete cure may require 24 to 72 hours depending on temperature and humidity.; Cure Rate : Allow (at 77°F(25°C)); 12 hours for foot traffic; 18 hours for light traffic; 24 hours for normal operations
- HIGHLIGHTS
MICOROX® 1882 SEALER is a two- component 100% solids epoxy sealer designed to offer superior abrasion and chemical resistance.
- Surface Preparation
When used as a topcoat for MICOROX® flooring systems: To remove trowel marks and present an even, level surface for 1882 SEALER, use a floor grinder with medium stones and vacuum resulting dust before applying 1882 Sealer.. When applied as a concrete floor sealer, 1882 SEALER bonds existing surfaces with an appropriate primer. Substrate must be exposed by acid-etch or mechanical means for secure bonding.
- Application Areas
Clarifiers Epoxy floors Pits ,Trenches Concrete floors Sumps ,Stock chests ,Wastewater vessels.
- Temperature Limitations
During the installation and cure of 1882 SEALER, surface temperatures of 70° F - 90° F are recommended. 1882 SEALER should also be used at room temperatures.
- Certifications and Compliance
- USDA Certified
- Ready to Use Product Features
- Abrasion Resistant
- Chemical Resistant
- Corrosion Resistant
- Good Penetration
- Compatible Substrates and Surfaces
- Concrete
Technical data
Table 1 of 1
14 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Compressive Strength | 11800.0 | psi | ASTMD-695-77 |
| Compressive Modulus | 1.95 x 10⁵ | psi | ASTMD-695-77 |
| Tensile Strength | 7100.0 | psi | ASTM D-638-77a |
| Tensile Modulus | 3.6 x 10⁴ | psi | ASTM D-638-77a |
| Tensile Elongation | 10.7 | % | ASTM D 638-77a |
| Flexural Strength | 12500.0 | psi | ASTM D-790-71 |
| Flexural Modulus | 3.7 X 10⁵ | psi | ASTM D-790-71 |
| Hardness | 80 - 85 | Shore D | ASTM D-2240/Durometer |
| Bond Strength (100% Concrete Failure) | 400.0 | psi | — |
| Abrasion Resistance | 0.04 | gm /1000 revolutions | ASTM D-4060, Taber Abrader,5-17 wheel, 1,000 gm load |
| Flammability | max. 0.25 | inches | ASTM D-635 |
| Water Absorption | 0.1 | % | ASTM C-413 |
