Permatec 5000
PERMATEC 5000 floor topping is a 100% solids, unique blend of polymers with an epoxy novolac base. The PERMATEC 5000 system consists of a two component resin binder and graded aggregate. It is applied with a trowel or screed rake at 1/8 -1/4 inches (125 - 250 mils) in a one coat application including a silica broadcast. There is no need for a primer or sealer coat. An optional glaze coat may be used to improve the appearance and cleanability. The vertical formulation of PERMATEC 5000 is trowel applied at 1/8 inches (125 mils).
Product families
Applications
- Floor Coatings
Product Families
- Top Coats
Other characteristics
- Brand
- Permatec
- Features
Chemical Resistant, Fast Cure, Skid Resistant, Wear Resistant; PERMATEC 5000 is a 100% solids system and allows for a fast application where outstanding chemical and wear resistance are required.; PERMATEC 5000 can be installed over most sound floors including old or new concrete and most types of repair mortars.; At varying thicknesses up to 1/4 inches, the PERMATEC 5000 system provides long term chemical resistance for splash and spill, or immersion in a wide range of chemicals.; PERMATEC 5000 is similar to PERMATEC 3000 & 4000 but provides a higher degree of chemical resistance to concentrated acids, caustics and solvents.; As with all PERMATEC systems, PERMATEC 5000 provides excellent physical protection even in the harshest industrial settings.; Rapid cure resulting in minimal downtime.; 100% non-porous; Odor free; Non-skid safety finish; Can be applied over damp concrete.
- Product Type
2K (2 component) Coating, Solventless & High Solids Coating; 2K (2 component) Coating; Solventless & High Solids Coating
- Compatible Substrates & Surfaces
- Concrete
- Mixing
Prior to application, the PERMATEC 5000 (Resin, Hardener and Silica) and the substrate should be between 65°F and 90°F.; In order to maintain a clean mixer from batch to batch, the Resin (Part A) and a portion of the Silica (Part C) should be added to the mixer and agitated long enough to clean the blades.; Add the Hardener (Part B) only when the batch is ready to be applied.; Mix for approximately 30 seconds - 1 minute, then add the remainder of the Silica and mix for another 90 seconds.; Pour immediately onto the floor.
- Safety
PERMATEC 5000 contains blended epoxies as the resin and blended amines as the hardener. Protective clothing and gloves are recommended to prevent sensitization to these materials. In case of ingestion or eye contact, it is advisable to contact a physician immediately.
- Markets
- Building & Construction
- Function
The primary use of PERMATEC 5000 is as a high strength floor topping for industrial service where severe mechanical abuse and/or chemical exposure is anticipated.
- PACKAGING
PERMATEC 5000 is available in 20, 100, and 1000 square foot units based on 1/4 inch applications. Each unit consists of pre-measured components, Part A (Resin) and Part B (Hardener). Graded aggregates are available or may be sourced locally.
- Technology
- Ready-to-Use Products
- Labeling Claims
- Odor-free
Technical data
Table 1 of 1
7 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Solids (Volume) | 100.0 | % | — |
| Compressive Strength | 14000.0 | psi | ASTM C579 |
| Flexural Strength | 5500.0 | psi | ASTM D790 |
| Tensile Strength | 2200.0 | psi | ASTM D307 |
| Taber Abrasion (CS 17 Wheels, Loss/1000 Cycles, w/1000 gms) | 25.0 | mg | ASTM D4060 |
| Bond Strength to Concrete | Exceeds Tensile Stregth of Concrete | — | ASTM D4541 |
| Water Absorption | 0.1 | % | ASTM D413 |
