Permacoat 4000 HT
- Chemical Family
- Epoxy & Epoxy Derivatives
PERMACOAT 4000 HT is a 100% solids epoxy floor coating designed for high temperature applications commonly found in many manufacturing processes. PERMACOAT 4000 HT is designed to withstand constant temperatures to 212°F (100°C) and intermittent exposures to 250°F (122°C). PERMACOAT 4000 consists of two components, resin and hardener, in both the horizontal and vertical formulations. Its application is accomplished with rubber squeegees and short nap paint rollers.
Product families
Applications
- Floor Coatings
Product Families
- Top Coats
Other characteristics
- Brand
- Permacoat
- Features
Chemical Resistant, High Temperature Performance, Low Odor, Rapid Cure Response, Skid Resistant; PERMACOAT 4000 HT allows for a fast, easy application. It also offers chemical resistance higher than those found in paints and other thin mil coatings.; At 30 - 50 mils, PERMACOAT 4000 HT provides excellent chemical resistance for splash and spill exposures.; In addition, when applied at 50 - 80 mils, it can often be recommended for containment service.; Rapid cure resulting in minimal downtime.; Very low odor.; Non-skid safety finish.
- Product Type
2K (2 component) Coating, Epoxy Coating, Solventless & High Solids Coating; 2K (2 component) Coating; Epoxy Coating; Solventless & High Solids Coating
- Application Method
- Roller, Wipe
- Compatible Substrates & Surfaces
- Concrete, Metal, Steel, Wood
- Safety
PERMACOAT 4000 HT contains blended epoxies as the resin and blended amines as the hardener. Protective clothing and gloves are recommended to prevent sensitization to these materials. In case of ingestion or eye contact, it is advisable to contact a physician immediately.
- Markets
- Building & Construction
- Clean Up
All mixing and application equipment should be cleaned immediately after use. If this is done, soap and water or biodegradable cleaners can be used. If the material has begun to set, more aggressive solvents will be necessary.
- Cure Time Cycle
The cure time of PERMACoat 4000 HT and other resinous systems are very dependent upon the temperature of the substrate. The chart below represents the approximate times for the respective service conditions, following the last coat:
- Function
PERMACOAT 4000 HT is designed as a heavy duty (30 - 90 mils) floor coating and/or secondary containment system where extensive mechanical abuse and chemical exposures are anticipated.; PERMACOAT 4000 HT can be installed over most sound substrates, including old or new concrete, steel and wood.; PERMACOAT 4000 HT provides a costeffective alternative to high build floor toppings.
- PACKAGING
PERMACOAT 4000 HT is packaged in one and three gallon units. Each unit consists of pre-measured components, Part A (Resin) and Part B (Hardener).
- Maintenance
For systems designed for splash and spill exposures, routine wash downs are recommended to reduce the length of chemical exposure. This step is not necessary where the product is recommended for containment service.
- Technology
- Ready-to-Use Products
- Application Methods
- Roller
- Wipe
Technical data
Table 1 of 1
6 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Solids (Volume) | 100.0 | % | — |
| Compressive Strength | 15000.0 | psi | ASTM C579-82 |
| Flexural Strength | 17000.0 | psi | ASTM C580-85 |
| Tensile Strength | 11300.0 | psi | ASTM D307-83 |
| Hardness | 80 - 85 | Shore D | ASTM D2240 |
| Taber Abrasion (CS 17 Wheels, Loss/1000 Cycles) | 25.0 | mg | ASTM C501-80 |
