JETSET™ 100 - TRAFFIC COATING
- Chemical Family
- Epoxy & Epoxy Derivatives
JETSET 100™ Traffic Coating is a low odor, zero VOCs and 100% solids solvent-free, twocomponent epoxy for heavy duty protection. It is designed for new or old concrete or steel. Consult with the manufacturer for additional acceptable substrates. JETSET 100™ is high gloss and chemical resistant.
Product families
Applications
- Concrete Coatings & Stains
Product Families
- Protective Coatings
Other characteristics
- Brand
- JETSET
- Features
- Chemical Resistant, High Gloss, Low Odor
- Product Type
- Epoxy Coating, Solventless & High Solids Coating
- Epoxy Coating
- Solventless & High Solids Coating
- Compatible Substrates & Surfaces
- Concrete, Elastomers & Rubbers, Metal, Steel
- Markets
- Paints & Coatings
- Pot Life
- 25 minutes
- Basic Uses
This high performance coating system is for new, old, uncoated or coated concrete. It is used forheavy foot and rubber wheeled vehicle traffic areas. JETSET 100™ has excellent intermittent chemical resistance for spills and can be power washed. It also has high impact resistance.
- Technology
- Ready-to-Use Products
- Labeling Claims
- VOC-free
- Packaging And Availability
- 1-gallon container including activator
- 5-gallon container including activator
- 55-gallon drum including activator
- Mixing Instructions
JETSET 100™ is a two-component pre-designed volume mix. To activate JETSET 100™, pourPart B into Part A and mix with low RPM mixer until there is a smooth consistency (approx. 2 minutes).Use all of the Part B (activator) supplied and make sure to scrape out thoroughly.; Option 1: Immediately pour the mixed contents on to the prepared surface in a straight line. Roll out tocomplete application to the desired thickness. Never leave JETSET 100™ in the pail. It will activateand set in the pail. Use entire contents at one time.; Option 2: Immediately pour the mixed contents on to the prepared surface in a straight line. Squeegeeto the desired thickness. Back roll to finish.; JETSET 100™ will take foot traffic in 6 to 7 hours at 72deg. F. It will be ready for vehicle traffic in 24 to 48 hours.; Check for hardness prior to heavy traffic. To obtain a non-slip surface, a light casting of silica can be cast following application of the JETSET 100™. A back roll will assist with adhesion.
- Application
New concrete shall be allowed 30 days to cure prior to overcoating with JETSET 100™. A moisture test should be performed prior to installation (consult manufacturer). Dense or old concrete can be treated with JETSET 100™. A water drop test is required to test for absorption. If there is no absorption, treat the concrete first with BDE1002™ as per manufacturers' specification. Power wash the entire area and let dry prior to coating. Previously coated surfaces must be clean, free from any oil or residue and dry. Gloss coatings must be lightly sanded and any loose or spalled concrete should be repaired prior to applying JETSET 100™.
- Ready to Use Product Features
- Chemical Resistant
- High Gloss
- Low Odor
- Compatible Substrates and Surfaces
- Concrete
- Elastomers & Rubbers
- Metal
- Steel
Technical data
Table 1 of 1
12 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Heat Deflection | 54.0 | — | ASTM D 648 |
| Tensile Strength | 9000.0 | psi | ASTM D 638 |
| Flexural Strength | 15000.0 | psi | ASTM D 790 |
| Tensile Elongation | 4.4 | % | — |
| Hardness | 84.0 | lbs./sq inch | Shore D |
| Impact | 1.05 | ft. lbs/inch | ASTM D256 |
| Application temperature | 55 - 95 | ºF | — |
| Re-coat | 10 - 24 | hours | — |
| Coverage (5mil thickness) | 300.0 | sq ft – 1 gallon/1 coat | — |
| Solids | 100.0 | % | — |
| Light traffic | 6 - 7 | hours | — |
| Vehicle traffic | 24 - 48 | hours | — |
