710 JETSET™ PRIMER
- Chemical Family
- Epoxy & Epoxy Derivatives
710 JET-SET™ PRIMER is used as the prime coat for all of the JET-SET™ coating systems. It can also be used as an inexpensive, hard, chemical resistant seal coat for new or old concrete floors and more.
Product families
Applications
- Primers & Lacquers
Product Families
- Primers & Sealers
Other characteristics
- Brand
- 710 JETSET
- Features
Abrasion Resistant, Chemical Resistant, Cost Effective, Food Contact Acceptable, Low Temperature Curing, Medium Hardness, Rapid Curing Speed
- Product Type
2K (2 component) Coating, Epoxy Coating, Primer, Solventless & High Solids Coating; 2K (2 component) Coating; Epoxy Coating; Primer; Solventless & High Solids Coating
- Compatible Substrates & Surfaces
- Concrete
- Primer
- Not required.
- Markets
- Printing & Packaging
- Thinner
- Never add thinners, 100% solids material.
- Clean Up
- 780 Thinner or 785 to clean equipment
- Pot Life
- Less than 15 minutes if both
- Shelf LIfe
6 months at 5 to 24°C/41 to 75°F inside storage out of sun away from direct heat.
- Technology
- Ready-to-Use Products
- Packaging Type
- Pails
- Major Advantages
100% solids; Exceptional chemical & abrasion resistance; Completely seals the pores of new or old concrete; Rapid cure; Low temperature applications; Agriculture Canada approved for incidental food contact
- Special Handling
The isophthalic resins used in these products have a flash point of 32ºC/90°F. Keep material awayfrom sparks, fire and heat. Keep containers closed. Extinguish fires with CO2. Store away from heat and out of direct sunlight. Keep work area well ventilated. Use an "Organic Vapor" type respirator when working with material.
- Application Instructions
Correct surface preparation is of the utmost importance. All concrete surfaces must be dry, clean and free from dust, oil, grease or any other contaminants. Apply 710 JET-SET™ PRIMER at the rate of 100 SQFT/L dependent on the profile.; New Concrete - Must be fully cured and free of laitance, form release agents, surface hardeners and any other foreign materials. Surface must be cleaned to achieve a profile similar to medium grade sandpaper by one of the following methods: Very light scarification or sandblasting followed by vacuum, acid etch and neutralize (use BDE-1002™ by Specialty Products Group® as per the manufacturer's instructions followed by a thorough flushing with clean water), litmus testing of the surface should show neutral.; Old Concrete -All existing coatings must be removed and then the surface prepared as above. All damaged concrete must be removed.
- Ready to Use Product Features
- Abrasion Resistant
- Chemical Resistant
- Cost Effective
- Food Contact Acceptable
- Low Temperature Curing
- Medium Hardness
- Rapid Curing Speed
- Compatible Substrates and Surfaces
- Concrete
Technical data
Table 1 of 1
14 rows| Characteristic | Value | Unit |
|---|---|---|
| Cure time (Initial set & recoat, Light Traffic, 30 to 45 minutes) | 2 - 4 | hours |
| Cure time (Initial set & recoat, Full Service, 30 to 45 minutes) | 4 - 8 | hours |
| Flash Point | 32 (90) | °C (°F) |
| Solids by Volume | 100.0 | % |
| Hardness Shore D | 87.0 | — |
| Abrasion resistance (Weight Loss with C-10 wheels) | No Loss | — |
| Abrasion resistance (Weight Loss with H-22 ceramic wheels) | 0.05 gm | gm |
| Weatherometer 500 hours | No change | — |
| Water Absorption | 0.74 | % |
| No. of Components | Two, Base resin & catalyst | — |
| Coverage ( 3 mil DFT) | 10 (100) | m² ( sq. ft/L) |
| Primer | Non-required | — |
