724 IM-KOTE™ FLOOR
724 IM-KOTE™ FLOOR is a profoundly crosslinked thermosetting polymer concrete system that forms a dense hard impermeable surface upon curing that is resistant to a very wide range of aggressive chemicals.
Product families
- Other Adhesives & Sealants
Other characteristics
- Brand
- 724 IM-KOTE
- Product Type
- Adhesive
- Compatible Substrates & Surfaces
- Brick, Concrete
- Colours
Natural, gray & terra cotta Additional colors and color matches available on specific order
- Markets
- Building & Construction
- Storage
Inside storage out of sun and away from direct heat.
- Basic Uses
As a 3/16" thick seamless floor topping for areas exposed to aggressive chemicals or areas subjected to high frequency trafficand concentrated loadings.; To repair or replace acid brick or ceramic tile.; To patch worn or spalled concrete.; To repair cracks.; To fill shallow potholes.
- Shelf LIfe
- 6 months at 5 to 24°C/41 to 75°F
- Technology
- Ready-to-Use Products
- Packaging Type
- Pails
- Major Advantages
Exceptional physical and chemical resistance characteristics.; Resistance to most commercially used chemicals.; One hour cure time at surface temperatures as low as - 30ºC.; Complete ultra-violet stability.; Approved by Agriculture Canada for incidental food contact.
- Special Handling
The isophthalic resins used in these products have a flash point of 32°C/90°F. Keep material away from sparks, fire and heat. Keep container closed. Extinguish fires with CO². Store away from heat and out of direct sunlight. Keep work area ventilated. Use an "Organic Vapor" type respirator when working with material.
- Application Instructions
Correct surface preparation is of the utmost importance. All concrete surfaces must be dry, clean and free from dust, oil, grease or any other contaminants. All surfaces must be primed with 710 IM-KOTE™ PRIMER at the rate of 75 to 100 SQFT/ L dependent on the profile. Mix all three components of 724 IM-KOTE™ FLOOR in strict accordance with manufacturer's instructions, transfer to primed area and rough spread. Trowelling is accomplished with strong, even strokes, compressing material well and squeezing it onto the primed surface to eliminate air voids. Specify application temperature range when ordering.; New Concrete - Must be fully cured and free of laitance, form release agents, surface hardeners and any other foreign materials. Surface must be cleaned to achieve a profile similar to medium grade sandpaper by one of the following methods: Very light scarification or sandblasting followed by vacuum, acid etch and neutralize (use BDE-1002™ by Specialty Products Group® as per the manufacturer's instructions followed by a thorough flushing with clean water), litmus testing of the surface should show neutral.; Old Concrete - All existing coatings must be removed and then the surface prepared as above. All damaged concrete must be removed.
- Ready to Use Product Features
- Chemical Resistant
- Excellent UV Stability
- Food Contact Acceptable
- Good Mechanical Properties
- Low Permeability
- Low Temperature Curing
- Compatible Substrates and Surfaces
- Brick
- Concrete
Technical data
Table 1 of 1
29 rows| Characteristic | Value | Unit |
|---|---|---|
| No. of Components | Three: (Base resin, catalyst and Aggregate Blend) | — |
| Compressive strength | 23,000 (159 ) | psi (MPa) |
| Tensile strength | 11,000 (76 ) | psi (MPa) |
| Flexural strength | 17,000 (117 ) | psi (MPa) |
| Barcol Hardness | 45—50 | — |
| Flash Point | 32 (90) | °C (°F) |
| Viscosity at 25°C | 300-600 | cps |
| Specific Gravity | 1.1 - 1.2 | — |
| Net Weight | 1.0 | kg/L |
| Solids by volume | 1.0 | — |
| Abrasion resistance -weight loss | 0.9 | gm |
| Weatherometer 500 hrs. | no change | — |
