United Adhesives OP4036
- Chemical Family
- Silicones
United Adhesives OP4036 is a fast cure optically clear silicone potting firm gel.
Product families
- Encapsulants
Other characteristics
- Cure Method
- Heat Cure
- Product Type
1K (1 component) Adhesive, 2K (2 component) Adhesive, Potting Compound; 1K (1 component) Adhesive; 2K (2 component) Adhesive; Potting Compound
- Application Area
Connectors, Electronic Components, Housing, LEDs, Optical Applications; Connectors; Electronic Components; Housing; LEDs; Optical Applications
- Application Method
- Injection
- Color
- Transparent
- Safety
OP4036 silicone contains neither toxic nor corrosive substances that might require special handling precautions. General hygiene regulations should be observed.
- Markets
- Electrical & Electronics
- Storage
OP4036 has a shelf life of at least 6 months when stored at < 5°C freezer in the originally sealed container. Storage beyond the date specified does not necessarily mean that the product is no longer usable. In this case however, the properties required for the intended use must be checked for quality assurance reasons.
- Shelf LIfe
- 6 months at 25°C (Viscosity double)
- Cure
- Heat Cure
- Technology
- Ready-to-Use Products
- Packaging Type
- Pails
- Characteristic
OP4036 is a two-part water clear potting gel. It is a flowable, addition-curing, silicone that cures fast at elevated temperature to a very firm optically clear rubbery gel for casting or injection molding of high performance optical components. It also cures in room temperature. It has noncorrosive and self-priming adhesion to various substrates. It stays thermo-optically stable with heat and UV exposure and will not yellowing over time. OP4036 can be automated to dispense from pails with auto mixing & dispensing pump or hand extruded from 50cc or 200cc ducal cartridge using dispensing gun with a mixing tube and a plunger.
- Labeling Claims
- Non-Corrosive
- Application Methods
- Injection
- Typical Applications
- Pot / encapsulate optical parts
- Coat various opt-electronic components
- LED, solar or other optical applications
- Seal lids, covers, housings, connectors
- Vibration dampening
- Thermal stress coupling
- Processing Instruction
Important! OP4036 is platinum cure system. Please keep applied surface / housing clean and avoid using this material on any place that contains sulfur, amine, phosphorous, organo-metals, acid, etc. because these contaminants could inhibit the cure the material. Please let the compound thoroughly thaw after taking it out from freezer. This typically needs half to one hour depending on the size of container.. We recommend running preliminary tests to optimize conditions for the particular application. Comprehensive processing instructions can be obtained by contacting directly to United Adhesives Inc.
- Special Features and Benefits
- Optically clear firm gel
- Non-yellowing and thermo-optically stable
- Two component and ready to apply
- Rom temperature curable
- Fast cure at elevated temperature
- Very soft for stress compliance
- Excellent dielectric properties
- Mechanical shock and vibration damping
Technical data
Table 1 of 2
3 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Density (Mixed) | 0.98 | Gram /cc | ASTM D792 |
| Mixing Ratio | 1:1 | Vol / wt | — |
| Viscosity (25°C, Mixed) | 4900.0 | cP.s | ASTM D2196 |
Table 2 of 2
16 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Coefficient Of Thermal Expansion | 270.0 | ppm/°C | IPC-TM-650 |
| Cure Time (125°C) | 5.0 | Minutes | Durometer |
| Cure Time (25°C) | 4.0 | Hours | Durometer |
| Cure Time (80°C) | 10.0 | Minutes | Durometer |
| Dielectric Constant (100 Hz) | 2.5 | — | ASTM D150 |
| Dielectric Strength | min. 480 | Volt/mil AC | ASTM D149 |
| Dissipation Factor (100 Hz) | max. 0.003 | — | ASTM D150 |
| Elongation | 140.0 | % | ASTM D638 |
| Hardness | 40.0 | Shore A | ASTM D2240 |
| Pot / Work Life (After Mix Part A And B, 25°C) | 30.0 | Minutes | Viscosity double |
| Refractive Index (589 Nm, 25°C) | 1.41 | — | ASTM D542 |
| Tensile Strength | 4.8 | Mpa | ASTM D638 |
