Eco-UVE™
- Chemical Family
- Epoxy & Epoxy Derivatives
Eco-UVE™ is a two-component epoxy with a high solids content and excellent UV resistance. It is one of the primary components of the metallic system and is commonly used to seal quartz and flake applications. Eco-UVE can be used as a stand-alone coating as well. For applications requiring a thicker product, an orange-peel option using fumed silica is available (instructions at the end of the document) (e.g., wall systems).
Other characteristics
- Brand
- Eco-UVE
- Features
- High Solids Content, UV Resistant
- Product Type
- 2K (2 component) Coating, Sealer
- 2K (2 component) Coating
- Sealer
- Application Method
- Roller
- Compatible Substrates & Surfaces
- Concrete, Plastics
- Markets
- Building & Construction
- Options
Colors: Use colorants at a rate of one unit per 3-gallon (11.34 liters) mix of Eco-UVE. Standard Colorants--White, Yellow and Light Gray will not impart total hide. Use these colorants at a rate of two units per 3-gallon (11.34 liters) mix. Similar colorants also may not hide as well. Refer to Color Selection Guide or consult Tennant Technical Support.
- Storage
Materials should be stored indoors between 65ºF (18ºC) and 90ºF (32ºC).
- Disposal
Dispose of all excess material, packaging and other waste in accordance with federal, state and local regulations.
- Shelf LIfe
- One year from date of manufacture.
- Limitations
Orange Peel: Eco-UVE with fumed silica can be used as a topcoat to achieve a textured appearance. Colors: Multiple coats may be needed to achieve complete hide in lighter systems. UV/Light Stability: This is an epoxy product with improved UV resistance, but it may amber/yellow over time. Thickness: The clear, thickened version of Eco-UVE with fumed silica will "ghost" or will appear cloudy if applied at >8 mils per coat. Contamination (Fisheyes): Products may fisheye if oil, silicones, mold release agents or other contaminants are present.
- Preparation
Ensure concrete is free of dirt, grease, oil or other contaminants. Certain types of contaminant may interfere with coating adhesion and cause fisheyes or defect in the coating. Scrub with detergent, rinse with clean water, and allow to fully dry. Concrete Preparation Options for Thin to Medium Film Applications (25 mils (0.63 mm) maximum) Diamond Grind: (results of diamond grinding may vary depending on technique and the hardness of the concrete. Additional mils may be required). Sweep to remove large debris and vacuum to remove fine dust. Light Blast: Use magnetic broom to remove excess shot, sweep to remove large debris and vacuum to remove fine dust. Concrete Preparation options for Thick-Film Applications Steel Shot Blast: Use magnetic broom to remove excess shot, sweep to remove large debris and vacuum to remove fine dust. Scarify: Sweep to remove large debris and vacuum to remove fine dust. Filling Joints: Depending on the preference of the facility owner, joints may or may not be filled. If the joints are filled, non-moving joints, i.e. contraction or control joints, can be hard filled with thickened epoxy or with a semi-rigid joint filler such as Eco-PJF™ or Eco-EJF™. Construction joints less than one inch wide may also be filled with Eco-PJF. Isolation or expansion joints must be filled with a flexible material designed for this purpose. Coating applied over filled joints may crack if there is concrete movement.
- Applications
Building & Construction — Other Building & Construction Applications
- Technology
- Ready-to-Use Products
- Certification
LEED® CREDIT – LEED Green Building Certification Program credits may be available: Indoor Environmental Quality - 4.2 Low-Emitting Materials, Paint & Coatings
- Packaging Type
- Pails
Technical data
Table 1 of 2
2 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Percent Solids (A+B) | 97.87 (96.25) | wt/vol | ASTM D2369 |
| Volatile Organic Compound (VOC, A+B) | 0.19 (23) | g/L / lb/gal | ASTM D3960 |
Table 2 of 2
9 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Abrasion Resistance (mg Loss Taber Abraser, CS-17 Taber Abrasion Wheel, 1,000 gram load, 1,000 Revolutions) | 57.8 | — | ASTM D4060 |
| Adhesion to Concrete (No Coating Adhesion Failure, Concrete Failed) | max. 1,250 (max. 8.62) | psi/ MPa | ASTM D4541 |
| Adhesion to Concrete (max Machine Can Register) | max. 480 (max. 3.31) | psi/ MPa | ASTM D7234 |
| Compressive Strength | 16,450 (113.419) | psi/MPa | ASTM D695 |
| Percent Elongation | 7.0 | — | ASTM D2370 |
| Hardness (0 sec / 75-80 at 15 sec) | 80 - 85 | Shore D | ASTM D2240 |
| Tensile Strength | 9,500 (65.500) | psi/MPa | ASTM D2370 |
| Thermal Stability / Heat Resistance (Tested on steel panel (5 hours at 158°F, No Softening or Change in Appearance) | No Slip/Flow | — | MIL-D-3134J, Section 4.6.3 |
| Water Absorption (24-hour Immersion, Resin Only, Increase in Weight) | 2.35 | % | ASTM D570 |
