Eco-MPE™
- Chemical Family
- Epoxy & Epoxy Derivatives
Eco-MPE™ is a two-component, neutral epoxy with a high solids content. Priming at 3 mils (76.2 microns) or build coat at up to 30 mils (762 microns) (1/32 inch). For thicker applications, a slurry option is available (instructions at the end of the document). Colors are not required.
Product families
- Fillers Levellers & Joints
Other characteristics
- Brand
- Eco-MPE
- Features
Excellent Leveling Properties, Good Sealant Properties, High Solids Content
- Product Type
- 2K (2 component) Coating, Primer
- 2K (2 component) Coating
- Primer
- Application Method
- Roller
- Compatible Substrates & Surfaces
- Concrete, Plastics
- Markets
- Building & Construction
- Storage
Materials should be stored indoors between 65ºF [18ºC] and 90ºF [32ºC].
- Disposal
Dispose of all excess material, packaging and other waste in accordance with federal, state and local regulations.
- Shelf LIfe
- One year from date of manufacture.
- Limitations
Colors: Multiple coats may be needed to achieve complete hide in lighter systems. UV/Light Stability: This product is not light stable and will yellow/amber over time. Contamination (Fisheyes): Products may fisheye if oil, silicones, mold release agents or other contaminants are present
- Preparation
Ensure concrete is free of dirt, grease, oil or other contaminants. Certain types of contaminant may interfere with coating adhesion and cause fisheyes or defect in the coating. Scrub with detergent, rinse with clean water, and allow to fully dry. Concrete Preparation Options for Thin to Medium Film Applications (25 mils (0.63 mm) maximum) Diamond Grind: (results of diamond grinding may vary depending on technique and the hardness of the concrete. Additional mils may be required). Sweep to remove large debris and vacuum to remove fine dust. Light Blast: Use magnetic broom to remove excess shot, sweep to remove large debris and vacuum to remove fine dust. Concrete Preparation options for Thick-Film Applications Steel Shot Blast: Use magnetic broom to remove excess shot, sweep to remove large debris and vacuum to remove fine dust. Scarify: Sweep to remove large debris and vacuum to remove fine dust. Filling Joints: Depending on the preference of the facility owner, joints may or may not be filled. If the joints are filled, non-moving joints, i.e. contraction or control joints, can be hard filled with thickened epoxy or with a semi-rigid joint filler such as Eco-PJF™ or Eco-EJF™. Construction joints less than one inch wide may also be filled with Eco-PJF. Isolation or expansion joints must be filled with a flexible material designed for this purpose. Coating applied over filled joints may crack if there is concrete movement.
- Technology
- Ready-to-Use Products
- Certification
LEED® v4 – Indoor Air Quality credits available. Meets requirements per CDPH-CA Section 01350 Standard Method for the Testing and Evaluation of Volatile Organic Chemical Emissions from Indoor Sources Using Environmental chambers Version 1.2.
- Packaging Type
- Cans
- Pails
Technical data
Table 1 of 2
2 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Percent Solids (A+B) | 95.45 (94.56) | wt/vol | ASTM D1475 |
| Volatile Organic Compound (VOC, A+B) | 0.41 (49) | g/L/lb/gal | ASTM D3960 |
Table 2 of 2
8 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Abrasion Resistance (mg Loss Taber Abraser, CS-17 Taber Abrasion Wheel, 1,000 gram load, 1,000 Revolutions, Independent Lab Test Result) | 83.1 | — | ASTM D4060 |
| Adhesion to Concrete (Concrete Failed) | 732 (4.48) | psi/ MPa | ASTM D7234 |
| Adhesion to Concrete (Concrete Failed) | 450 (3.10) | psi/ MPa | ASTM D4541 |
| Coefficient of Friction (COF - James Friction Tester) | 0.59 - 0.62 | — | ASTM D2047 |
| Compressive Strength | 13,500 (93.079) | psi/MPa | ASTM D695 |
| Percent Elongation | 5.0 | — | ASTM D2370 |
| Hardness (0 sec / 75-80 at 15 sec) | 80 - 85 | Shore D | ASTM D2240 |
| Tensile Strength | 8,000 (55,158) | psi/MPa | ASTM D2370 |
