Eco-SCT™
Eco-SCT™ is a three-component high solids epoxy with conductive powder. It is applied at a thickness of 15-20 mils (0.38-0.51 mm) over a coat of Tennant epoxy that is electrically insulating.
Product families
- Top Coats
Other characteristics
- Brand
- Eco-SCT
- Features
Conductive, High Solids Content, Low Odor, Static-Dissipative
- Product Type
- 3K Coating, Top Coat
- 3K Coating
- Top Coat
- Application Method
- Roller
- Compatible Substrates & Surfaces
- Concrete
- Markets
- Automotive & Transportation
- Electrical & Electronics
- Options
Colors in Eco-SCT. Tennant Colorants must be added to Eco-SCT. DO NOT use White. Use Light Gray, Canada Gray, Medium Gray, Summer Gray, California Gray, Sandy Beige, Baby Blue, Sky Blue, and Tile Red at a rate of 1/2 pint (8 fluid oz.) per 3.05-gallon (11.55 liter) unit of Eco-SCT. Contact Tennant Company coatings technical support if additional colorants are desired as they may not be compatible.
- Storage
Materials should be stored indoors between 65ºF [18ºC] and 90ºF [32ºC].
- Disposal
Dispose of all excess material, packaging and other waste in accordance with federal, state and local regulations.
- Shelf LIfe
- One year from date of manufacture.
- Limitations
Colors: Use of color is required in Eco-SCT. DO NOT USE White. Hide: The topcoat must be applied over a pigmented primer or existing coating of similar color to obtain color hide in Eco-SCT. The resulting system color will be closer to the primer. Contamination (Fisheyes): Product may fisheye if oil, silicones, mold release agents or other contaminants are present.
- Preparation
Detergent scrub and rinse with clean water to remove surface dirt, grease, oil and contaminants. One of the following preparation methods may be used: EasyPrep™: With 25/35 grit concrete tool, coating system must be 10-25 mils (0.25-0.64 mm). Diamond Grinding: Coating system thickness varies with the type of diamond used. Sweep and vacuum to remove fine dust. Steel Shot Blast: Coating system must be >16 mils (>0.41 mm). Use magnetic broom to remove excess shot, sweep to remove large debris and vacuum to remove fine dust. Scarify: Coating system must be >25 mils (>0.64 mm). Sweep to remove large debris and vacuum to remove fine dust. JOINTS: Depending on the preference of the facility owner, joints may or may not be filled. If the joints are filled, non-moving joints, i.e. contraction or control joints, can be hard filled with thickened, 100% solids epoxy or with a semi-rigid joint filler such as Eco-PJF™ or Eco-EJF™. Construction joints less than one inch wide may also be filled with Eco-PJF. Isolation or expansion joints must be filled with a flexible material designed for this purpose.
- Technology
- Ready-to-Use Products
- Certification
ELECTROSTATIC DISCHARGE CONTROL - Meets ANSI/ESD S20.20-2014 for floor resistance readings between 1x105 and 1x109 ohms and <100 volts Body Voltage Generation LEED® v4 – Indoor Air Quality credits available. - Meets requirements per CDPH-CA Section 01350 Standard Method for the Testing and Evaluation of Volatile Organic Chemical Emissions from Indoor Sources Using Environmental chambers Version 1.2.
Technical data
Table 1 of 2
6 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Abrasion Resistance (Taber Abraser CS-17 Taber Abrasion Wheel, 1,000 gram load, 1,000 Revolutions) | 90 - 100 | — | ASTM D4060 |
| Coefficient of Friction (COF - James Friction Tester) | 0.50 - 0.55 | — | ASTM D2047 |
| Coefficient of Friction (COF - Wet Static BOT 3000) | 0.97 | — | ANSI/NFSI B101.1-2009 |
| Percent Solids (A+B+C) | 92.30 (84.92) | wt/vol | ASTM D2369 |
| Volatile Organic Compound (VOC, A+B+C) | 0.79 (94) | g/L / lb/gal | ASTM D3960 |
| Water Absorption (24-hour immersion, Weight Increase) | 0.002 | % | ASTM D570 |
Table 2 of 2
1 row| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Surface Resistance Point to Point / Point to Ground | 1x105 - 1x109 | ohms | ESD Assoc. ANSI/ESD STM 7.1-2013 |
