Eco-SDS™ Satin
- Chemical Family
- Urethanes
Eco-SDS™ Satin Satin is a light-stable urethane with conductive filler that provides static dissipative properties. This coating has a satin finish for long-term durability.
Product families
- Other Paints & Coatings
Other characteristics
- Brand
- Eco-SDS
- Features
Conductive, Good Light Stability, High Durability, Long Term Protection, Low Odor, Satin Finish, Static-Dissipative
- Product Type
- Coating
- Markets
- Automotive & Transportation
- Electrical & Electronics
- Options
Use the same color in the epoxy and Eco-SDS Satin. White is not recommended for this system. Colors in Tennant Epoxy: Use colorants at a rate of one unit per 3-gallon (11.34 liters) mix. Standard Colorants—Yellow and Light Gray will not impart total hide. Use these colorants at a rate of two units per 3-gallon (11.34 liters) mix. Similar colorants also may not hide as well. Refer to Color Selection Guide or consult Tennant Technical Support. Colors in Eco-SDS Satin: Use Colorants at a rate of one-half unit per 1-gallon (3.78 liters) mix.
- Storage
Materials should be stored indoors between 65ºF [18ºC] and 90ºF [32ºC].
- Disposal
Dispose of all excess material, packaging and other waste in accordance with federal, state and local regulations.
- Shelf LIfe
- One year from date of manufacture.
- Limitations
Colors: The use of color is recommended in Eco-SDS Satin. DO NOT USE White. Hide: The topcoat must be applied over a pigmented primer or existing coating of similar color to obtain color hide in Eco-SDS Satin. The resulting system color will be closer to the primer. Contamination (Fisheyes): Product may fisheye if oil, silicones, mold release agents or other contaminants are present. Chemical Resistance / Staining: Reduced chemical resistance and staining is possible in pigmented versions of the system.
- Preparation
Detergent scrub and rinse with clean water to remove surface dirt, grease, oil and contaminants. THICK FILM APPLICATIONS (25 mils / 0.64 mm): Steel Shot Blast: Use magnetic broom to remove excess shot, sweep to remove large debris and vacuum to remove fine dust. Diamond Grind: Sweep to remove large debris and vacuum to remove fine dust. JOINTS: Depending on the preference of the facility owner, joints may or may not be filled. If the joints are filled, non-moving joints, i.e. contraction or control joints, can be hard filled with thickened, 100% solids epoxy or with a semi-rigid joint filler such as Eco-PJF™ or Eco-EJF™. Construction joints less than one inch wide may also be filled with Eco-PJF. Isolation or expansion joints must be filled with a flexible material designed for this purpose.
- Technology
- Ready-to-Use Products
- Certification
ELECTROSTATIC DISCHARGE CONTROL - Meets ANSI/ESD S20.20-2007 for resistance <1x109 ohms and <100 volts Body Voltage Generation LEED® v4 – Indoor Air Quality credits available. Meets requirements per CDPH-CA Section 01350 Standard Method for the Testing and Evaluation of Volatile Organic Chemical Emissions from Indoor Sources Using Environmental chambers Version 1.2.
Technical data
Table 1 of 2
9 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Abrasion Resistance (Taber Abraser CS-17 Taber Abrasion Wheel, 1,000 gram load, 1,000 Revolutions) | 38.0 | — | ASTM D4060 |
| Coefficient of Friction (COF - James Friction Tester) | 0.5 | — | ASTM D2047 |
| Coefficient of Friction (COF - Wet Static BOT 3000) | 0.95 | — | ANSI/NFSI B101.1 |
| Flammability/Rate of Burn (Topcoat Resin) | 182.0 | mm/min | ASTM D635 |
| König Hardness (3 mil / 0.08 mm Film) (Topcoat Resin Only) | 171.3 | — | ASTM D4366 |
| Percent Solids (A+B+C) | 93.67 (92.49) | wt/vol | ASTM D2369 |
| Resistance to Yellowing (As Measured Using ASTM D2244 After 1000 Consecutive Hours UV Exposure in QUV.) | max. 10 | — | ASTM G154 |
| Volatile Organic Compound (VOC, A+B+C) | 0.05 (6) | g/L / lb/gal | ASTM D3960 |
| Water Absorption (24-hour immersion, Weight Increase) | 0.2 | % | ASTM D570 |
Table 2 of 2
5 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Body Voltage Decay (With ESD Shoes or Heel Straps, 1,000 volts to <10 volts, Second) | max. 1.0 | psi/ MPa | AATCC 134-1979 (modified) |
| Body Voltage Generation (With ESD Shoes) | 12.0 | volts | ANSI/ESD STM 97.2 (ANSI/ESD S20.20 - Method 2) |
| Body Voltage Generation (With Heel Straps) | 32.0 | volts | ANSI/ESD STM 97.2 (ANSI/ESD S20.20 - Method 2) |
| Resistance to Ground in Combination with a Person (ESD Shoes or Heel Straps) | max. 3.5 x 107 | ohms | ANSI/ESD STM 97.1 (ANSI/ESD S20.20 - Method 1) |
| Surface Resistance Point to Point / Point to Ground | 1x105 - 1x109 | ohms | ESD Assoc. ANSI/ESD STM 7.1-2013 |
