AQUAFIN® PRO-Tekt Topcoat PA

Other characteristics

Brand

AQUAFIN

Features

Good Abrasion Resistance, Good UV Stability, Low Odor

Product Type

2K (2 component) Coating, Solventless & High Solids Coating, Top Coat

Note

Proper application is the responsibility of the user. Field visits by AQUAFIN personnel are for the purpose of making technical recommendations and not for supervising or providing quality control on-site.

Curing

• PRO-Tekt Topcoat PA is self-curing. • Environmental conditions may accelerate or slow down curing times

Mixing

PRO-Tekt Topcoat PA is supplied in the appropriate mixing ratio. Always mix full units. • Use chemical resistant Nitrile gloves and goggles when mixing or applying PRO-Tekt Topcoat PA. • Material should be between 60°F (15°C) and 85°F (29°C) at time of mixing. 1. Pre-mix Component A for 30 secs until uniform in color. 2. Open each container carefully. Do not spill material. 3. Pour all contents of Component B into Component A (packaged in the larger 5-gal pail). 4. Mix material using a jiffy style paddle at low speed for a minimum 60 seconds until a uniform homogenous color is achieved 5. Thoroughly scrape sides of pail as material is placed in a clean secondary container. Mix for an additional 15- 20 seconds. NOTE: Extended mixing times can result in premature gel times.

Show in full

Safety

Refer to SDS. For commercial use only. Avoid contact with skin and eyes. Wear Nitrile gloves and safety goggles during mixing and application. After contact with skin, wash with plenty of water. In case of eye contact, rinse immediately with plenty of water for 15 minutes and seek medical advice. KEEP OUT OF REACH OF CHILDREN. LIMITED WARRANTY: AQUAFIN, INC. warrants this product for a period of one year from the date of installation to be manufactured free of defects and to be consistent with its technical properties as stated in our current Technical Datasheet. This product must be used as directed and within its stated shelf life. AQUAFIN, INC. will replace or at our discretion refund the purchase price of any product, excluding cost of labor, which is proven to be defective. Our product recommendations are based on industry standards and testing procedures. It is the buyer's obligation to test the suitability of the product for an intended use prior to using it. We assume no warranties written, expressed or implied as to any specific methods of application or use of the product. AQUAFIN, INC. MAKES NO WARRANTY AS TO MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE AND THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED. AQUAFIN, INC. shall not be liable for damages of any sort including remote or consequential damages, down time, or delay. Any claim for a defective product must be filed within 30 days of discovery of a problem, and must be submitted with written proof of purchase. For Professional Use Only.

Show in full

Markets

Building & Construction

Clean Up

Promptly wash hands and tools with an approved solvent before material hardens. Cured material must be removed mechanically.

PACKAGING

38.24 lbs/17.35 kg Kit (4.2 gallon/15.9 Liter) Comp A: 19.12 lbs (8.67 kg) Comp B: 19.12 lbs (8.67 kg)

Advantages

• Low odor during application and cure. • Quick return to service. • UV stable. • High abrasion resistance. • Zero VOC's.

Shelf LIfe

Shelf life is 12 months in closed, original packaging, stored in a dry, cool place, above 50°F (10°C) and below 85°F (30°C).

Application

PRO-Tekt Topcoat should be applied to properly applied PRO-Tekt Trafficoat after a minimum of 4 hours and a maximum of 48 hours. • Immediately after mixing, pour PRO-Tekt Topcoat in sufficient quantity onto surface and uniformly distribute with a 1/8" notched squeegee. • Apply PRO-Tekt Topcoat at 66 — 70 sq ft /gal @ 21-25 wet mils (rate will vary based upon aggregate load and amplitude) • Follow with a 1/4" - 3/8" non-shed roller, back rolling at right angle (90 degrees) to the squeegee application to achieve uniform coverage.

Show in full