Ebalta Kunststoff Gmbh LH 22GL
- Chemical Family
- Epoxy & Epoxy Derivatives
Ebalta LH 22 / GL is an epoxy laminating resin, which, depending on its application, can be used with the slow GL hardener or the faster GR hardener. They distinguish by minimal physiolgical effects. Regarding dimensional accuracy and –stability, laminates made of ebalta LH 22, even come up to great demands. Due to its long potlife ebalta LH 22/GL is especially suitable for large-area and thick laminates, which also with a thickness of more than 10 mm, applied in one step, cure without any shrinkage at room temperature.
Product families
Applications
- Exterior & Body
- Interior
- Interior Fixtures
- Wallcoverings & Decorative Laminates
Product Families
- Epoxies
Other characteristics
- End Uses
Automotive Applications, Automotive Exterior Parts, Automotive Interior Parts, Laminates, Modeling Material
- Polymer Name
- Epoxy Resins & Compounds
- Flexural Strength
- 90.0 - 110.0 MPa
- Processing Methods
- Laminating
- Basis
- Laminating resin
- Markets
- Automotive & Transportation
- Building & Construction
- Storing
At appropriate storage 18-25°C. Occuring crystallization due to disadvantageous storage conditions can be made return by warming up the material at approx. 60° C for some hours. Opened containers should be closed immediately after use and be protected against moisture. This material should be used up as soon as possible. Shelf life is indicated on the labels
- Properties
dimensionally accurate long potlife low exothermic character
- Technology
- Plastics
- Material Features
- Excellent Dimensional Accuracy
- Low Exotherm
- Package Unit
Packing size - Resin 6 x 0,800 kg / Hardener 6 x 0,200kg = 6,000 kg; Units - 6,000 kg / 20,000 kg / 220,000
- Processing Instruction
The temperature of material and processing should be between 18 and 25° C. The mixing of resin and hardener should be made intensively and if possible without any bubbles at room temperature. We recommend a post curing with a temperature rise of about 10°C/hour. Difficult geometries should be supported during the curing cycle. Afterwards the part should be cooled down at about 20°C/hour.
- Plastics and Elastomers End Uses
- Automotive Applications
- Automotive Exterior Parts
- Automotive Interior Parts
- Laminates
- Modeling Material
- Plastics and Elastomers Functions
- Resin
- Plastics and Elastomers Processing Methods
- Laminating
Technical data
Table 1 of 1
11 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Shore hardness | 86 ± 3 | Shore D | DIN ISO 7619-1 |
| Viscosity (25°C) | 1300 ± 200 | mPa.s | — |
| Compressive Strength | 95 ± 0.8 | MPa | EN ISO 604 |
| Density (20°C) | 1,35 ± 0,03 | g/cm3 | — |
| Flexural elongation at break | 3.6 ± 0.4 | % | EN ISO 178 |
| Pot Life (200g/20°C) | 40 - 45 | minutes | — |
| Flexural modulus | 3960 ± 150 | MPa | EN ISO 178 |
| Curing time at RT | 16 - 24 | Hrs | — |
| Flexural strength | 100 ± 10 | MPa | EN ISO 178 |
| Heat resistance (HDT) | 64 ± 2 | °C | DIN EN ISO 75 B |
| Impact resistance (Charpy) | 18 ± 3.5 | kJ/m2 | EN ISO 179 |
