SetWORX™ UV-35G
- Chemical Family
- Epoxy & Epoxy Derivatives
EPOXIBOND™ EB-153 is unfilled, low viscosity, heat curing, high temperature resistant epoxy adhesive. It maintains high lap shear strength up to 210°C and has excellent thermal and chemical resistance. It can be used for bonding, coating, and sealing applications where a thin film with high insulating resistance is required, particularly at elevated temperatures. It is recommended for bonding metals, glass, and ceramic substrates. It has long pot-life and has an amber color change upon cure.
Product families
Applications
- Industrial Adhesives & Sealants
- Industrial Manufacturing
- Medical Devices & Assemblies
- Optical Fiber & Telecom
Product Families
- Encapsulants
- Structural Adhesives
Other characteristics
- Brand
- SetWORX
- Cure Method
- Air Dry, Heat Cure
- Product Type
- 2K (2 component) Adhesive, Adhesive
- 2K (2 component) Adhesive
- Adhesive
- Application Area
Medical Applications, Medical Devices, Optical Applications, Optoelectronics Devices; Medical Applications; Medical Devices; Optical Applications; Optoelectronics Devices
- Application Method
- Gun
- Markets
- Adhesives & Sealants
- Electrical & Electronics
- Healthcare & Pharma
- Industrial
- Features
UV/Epoxy hybrid system; Gels within seconds upon UV exposure and fully cures at ambient or elevated temperatures; UV-35G can be used as an adhesive or for small encapsulation applications
- Shelf LIfe
- 12 Months
- Cure
- Air Dry
- Heat Cure
- Technology
- Ready-to-Use Products
- Packaging Type
- Cartridges
- Application Methods
- Gun
- Curing
- Recommended Cure
- 6-8 sec light exposure + 1 hr at 65°C
- Alternate Cure
- 1 hr at 65°C or 24 hr at 25°C
- Safety Information
- For Industrial Use Only
- Practices of good housekeeping, safety and cleanliness should be followed before, during and after use.
- Warning
- Although the system contains low volatility materials, care should be taken in handling. Adequate ventilation of work place and ovens is essential. These materials may cause injury to the skin following prolonged or repeated contact and dermatitis in susceptible individuals. In case of skin contact, wash thoroughly with soap and water. For eyes, flush immediately with plenty of water for at least 10 minutes and seek medical attention. Refer to Material Safety Data Sheet for additional health and safety information.
- Use Instructions
To use simply insert the cartridge into the application gun and start the plunger into the cylinders using light pressure on the trigger. Next, remove the cartridge cap and expel a small amount of adhesive to be sure both sides are flowing evenly and freely. If automatic mixing of resin and hardener is desired, attach the mixing nozzle to the end of the cartridge and begin dispensing the adhesive. For hand mixing, expel the desired amount of the adhesive and mix thoroughly. Mix approximately 15 seconds after uniform color is obtained.
- Shelf Life Storage
Product shall be ideally stored in a dry location in unopened containers at a temperature between 20°C to 28°C unless otherwise labeled. The shelf life of these materials is 12 months when stored in unopened containers at an average temperature of 25°C.
- Certifications and Compliance
- ISO 9001
- REACH (Europe)
- RoHS Compliant
- Ready to Use Product Features
- UV Curable
Technical data
Table 1 of 2
12 rows| Characteristic | Value | Unit |
|---|---|---|
| Specific Gravity | 1.1 | — |
| Hardness | 86 | Shore D |
| Lap Shear Strength to Aluminium | 3000 | psi |
| T-peel Strength to Aluminum (5-8mil bondline) | 30 | pli |
| Service Temperature Range | -55 to 120 | °C |
| Glass Transition Temperature (Tg) | 70 | °C |
| Coefficient of Linear Thermal Expansion (Below Tg) | 77 | 10⁻⁶/°C |
| Coefficient of Linear Thermal Expansion (Above Tg) | 195 | 10⁻⁶/°C |
| Dielectric Strength | 500 | Volts/mil |
| Dielectric Constant (at 1 kHz) | 4.28 | — |
| Dissipation Factor (at 1 kHz) | 0.4 | — |
| Volume Resistivity | 2x10¹⁵ | ohm-cm |
Table 2 of 2
5 rows| Characteristic | Value | Unit |
|---|---|---|
| Viscosity (at 25°C) | 4,000 - 7,000 | cps |
| Mix Ratio by Weight (Resin/Hardener) | 2:1 | — |
| Mix Ratio by Volume (Resin/Hardener) | 2:1 | — |
| Pot Life (at 25°C, 20 grams) | 60 - 70 | minutes |
| Recommended Light | 250 - 350 (320 - 365) | mW (nm) |
