To catalogue
SetWORX™ 5
- Chemical Family
- Epoxy & Epoxy Derivatives
EPOXIBOND™ EB-119M is a two component, low viscosity, heat cure epoxy designed for high temperature applications. It is especially well suited to fiber optic terminating, where optical fibers are "pot and polished" into connectors or ferrules.
Product families
Applications
Industrial — Chemical & Industrial Manufacturing
- Industrial Adhesives & Sealants
Adhesives & Sealants — Industrial & Assembly Adhesives
- Industrial Manufacturing
Product Families
Ready-to-Use Products — Adhesives & Sealants
- Structural Adhesives
Other characteristics
- Brand
- SetWORX
- Product Type
- Epoxy Adhesive
- Application Method
- Gun
- Compatible Substrates & Surfaces
- Metal, Plastics
- Markets
- Adhesives & Sealants
- Industrial
- Features
- General purpose 5 minute epoxy
- Strong bond to many substrates
- Fast cure, non-sag version also available
- Shelf LIfe
- 1 Year (at 25°C)
- Technology
- Ready-to-Use Products
- Packaging Type
- Bulk
- Cartridges
- Labeling Claims
- Bisphenol A-free
- Non-Hazardous
- Tin-free
- Packaging Options
Available in Pint, Quart, Gallon, and 5-gallon kits.; Also available in 50mL and 400mL dual cartridge systems.
- Application Methods
- Gun
- Curing
- Recommended Cure : 12 hrs. at 25°C
- Safety Information
- For Industrial Use Only
- These materials are intended for industrial use only, and the practices of good housekeeping, safety and cleanliness should be followed before, during and after use.
- Warning
- Although the system contains low volatility materials, care should be taken in handling. Adequate ventilation of work place and ovens is essential. These materials may cause injury to the skin following prolonged or repeated contact and dermatitis in susceptible individuals. Refer to Safety Data Sheet (SDS) for additional health and safety information.
- Use Instructions
- For high strength structural bonds, removal of surface contaminates such as paint, oxide films, oils, dust, mold release agents and all other surface contaminates.
- Dual Cartridges
- To use simply insert the cartridge into the application gun and start the plunger into the cylinders using light pressure on the trigger. Next, remove the cartridge cap and expel a small amount of adhesive to be sure both sides are flowing evenly and freely. If automatic mixing of resin and hardener is desired, attach the mixing nozzle to the end of the cartridge and begin dispensing the adhesive. For hand mixing, expel the desired amount of the adhesive and mix thoroughly. Mix approximately 15 seconds after uniform color is obtained.
- Bulk Containers
- Mix thoroughly by weight or volume in the proportions specified in Properties of Uncured Material section. Mix vigorously approximately 15 seconds after uniform color is obtained.
- Certifications and Compliance
- ISO 9001
- REACH (Europe)
- RoHS Compliant
- Ready to Use Product Features
- Electrically Insulating
- Fast Cure
- Fast Setting
- General Purpose
- Good Bonding Strength
- Good Peeling Strength
- Good Sagging Resistance
- High Performance
- Compatible Substrates and Surfaces
- Metal
- Plastics
Technical data
Table 1 of 2
9 rows| Characteristic | Value | Unit |
|---|---|---|
| Specific Gravity | 1.1 | — |
| Hardness | 85 | Shore D |
| Lap Shear Strength to Aluminium | 1900 | psi |
| Tensile Elongation | 1 | % |
| Service Temperature Range | -55 to 120 | °C |
| Dielectric Strength | 490 | Volts/mil |
| Dielectric Constant (at 1 kHz) | 4.28 | — |
| Dissipation Factor (at 1 kHz) | 0.4 | — |
| Volume Resistivity | 1x10¹⁴ | ohm-cm |
Table 2 of 2
5 rows| Characteristic | Value | Unit |
|---|---|---|
| Viscosity (at 25°C, Resin, Part-A) | 9,000 - 12,000 | cps |
| Viscosity (at 25°C, Hardener, Part-B) | 9,000 - 12,000 | cps |
| Mix Ratio by Weight or Volume (Adhesive/Hardener) | 1:1 | — |
| Pot Life (at 25°C, 20 grams) | 3 - 5 | minutes |
| Fixture Time (at 25°C) | 10 - 15 | minutes |
