SetWORX™ 411HP
- Chemical Family
- Epoxy & Epoxy Derivatives
SetWORX™ U-47MP is a two component, urethane adhesive & encapsulating material which cures to a resilient polyurethane polymer. It finds use as an adhesive, potting and encapsulating material. U-47MP provides a sag resistent bead when dispensed and delivers excellent adhesion to many materials including metals, glass and engineering plastics.
Product families
Applications
- Transportation Assembly
- Aerospace & Aviation
Product Families
- Structural Adhesives
Other characteristics
- Brand
- SetWORX
- Cure Method
- Heat Cure
- Product Type
- 1K (1 component) Adhesive, Conductive Adhesive
- 1K (1 component) Adhesive
- Conductive Adhesive
- Compatible Substrates & Surfaces
- Ceramic, Glass, Metal, Plastics
- Note
Typical Cured Properties After Recommended Cure : Tested at 25°C unless otherwise indicated
- Markets
- Automotive & Transportation
- Features
Toughened; Crack resistant; Component epoxy adhesive with fast cure at high temperatures; Excellent adhesion to metals, ceramics, glass and plastics
- Shelf LIfe
- 3 Months (at 25°C), 6 Months (at 0°C)
- Cure
- Heat Cure
- Technology
- Ready-to-Use Products
- Packaging Type
- Bulk
- Cartridges
- Packaging Options
Available in quart and gallon containers.; Also available in 30mL syringe or 10oz cartridge.
- Curing
Typical Curing Time : 30 min at 120°C or 20 min at 150°C
- Safety Information
- For Industrial Use Only
- Practices of good housekeeping, safety and cleanliness should be followed before, during and after use.
- Warning
- Although the system contains low volatility materials, care should be taken in handling. Adequate ventilation of work place and ovens is essential. These materials may cause injury to the skin following prolonged or repeated contact and dermatitis in susceptible individuals. In case of skin contact, wash thoroughly with soap and water. For eyes, flush immediately with plenty of water for at least 10 minutes and seek medical attention. Refer to Material Safety Data Sheet for additional health and safety information.
- Use Instructions
Dispense or apply needed amount on to the device or substrate.; Cure as recommended achieving the desired properties.; Typical cured properties were determined using recommended cure schedule. Some difference in properties may occur with the alternate or other cure schedules.
- Shelf Life Storage
The shelf life of these materials is 3 months when stored in unopened containers at an average temperature of 25°C or 6 months when stored at 0°C or below.
- Certifications and Compliance
- ISO 9001
- REACH (Europe)
- RoHS Compliant
- Ready to Use Product Features
- Crack Resistant
- Electrically Insulating
- Fast Cure
- Good Peeling Strength
- High Performance
- High Strength
- Impact Resistance
- Improved Shear Stability
- Compatible Substrates and Surfaces
- Ceramic
- Glass
- Metal
- Plastics
Technical data
Table 1 of 2
20 rows| Characteristic | Value | Unit |
|---|---|---|
| Specific Gravity | 1.44 | — |
| Hardness | 85 | Shore D |
| Elongation | max. 2 | % |
| Water Absorption (7days Submersion at 25°C) | 0.28 | % |
| Lap Shear Strength to Aluminium | 4500 | psi |
| Lap Shear Strength to Stainless Steel | 2500 | psi |
| Lap Shear Strength to Grit Blasted Steel | 4300 | psi |
| Lap Shear Strength to Polycarbonate | 2000 | psi |
| T-peel Strength to Steel (5-8mil bondline) | 50 | lb/in of width |
| Service Temperature Range | -55 to 200 | °C |
| Glass Transition Temperature (Tg) | min. 100 | °C |
| Coefficient of Linear Thermal Expansion (Below Tg) | 40 | 10⁻⁶/°C |
Table 2 of 2
2 rows| Characteristic | Value | Unit |
|---|---|---|
| Viscosity (at 25°C) | Paste | — |
| Pot Life (at 100°C, 20 grams) | 10 - 15 | minutes |
