EPOXIBOND™ EB-135
- Chemical Family
- Epoxy & Epoxy Derivatives
EPOXIBOND™ EB-107LP-2 is a two component - optical, medical, and semiconductor grade epoxy resin, with low viscosity, long pot-life, and good handling characteristics.
Product families
Applications
- Automotive Lighting
- Sealants
- Transportation Assembly
- Medical Devices & Assemblies
- Optical Fiber & Telecom
Product Families
- Structural Adhesives
Other characteristics
- Brand
- EPOXIBOND
- Cure Method
- Air Dry, Heat Cure
- Product Type
- 2K (2 component) Adhesive, Adhesive
- 2K (2 component) Adhesive
- Adhesive
- Application Area
Automotive Lighting, Medical Applications, Medical Devices, Optical Applications, Optoelectronics Devices; Automotive Lighting; Medical Applications; Medical Devices; Optical Applications; Optoelectronics Devices
- Application Method
- Gun
- Compatible Substrates & Surfaces
- Glass, Metal, Plastics
- Markets
- Automotive & Transportation
- Electrical & Electronics
- Healthcare & Pharma
- Features
- ISO-10993-5 tested for cytotoxicity
- NASA Outgassing Tested
- Shelf LIfe
- 12 Months
- Cure
- Air Dry
- Heat Cure
- Technology
- Ready-to-Use Products
- Packaging Type
- Cartridges
- Application Methods
- Gun
- Curing
- Recommended Cure
- 3 hours at 65°C
- Alternate Cure
- 24 hours at 25°C
- Safety Information
- For Industrial Use Only
- These materials are intended for industrial use only, and the practices of good housekeeping, safety and cleanliness should be followed before, during and after use.
- Warning
- Adequate ventilation of workplace and ovens is essential. In case of skin contact, wash thoroughly with soap and water. For eyes, flush immediately with plenty of water for at least 10 minutes and seek medical attention. Refer to Material Safety Data Sheet for additional health and safety information.
- Use Instructions
To use simply insert the cartridge into the application gun and start the plunger into the cylinders using light pressure on the trigger. Next, remove the cartridge cap and expel a small amount of adhesive to be sure both sides are flowing evenly and freely. If automatic mixing of resin and hardener is desired, attach the mixing nozzle to the end of the cartridge and begin dispensing the adhesive. For hand mixing, expel the desired amount of the adhesive and mix thoroughly. Mix approximately 15 seconds after uniform color is obtained.
- Shelf Life Storage
Product shall be ideally stored in a dry location in unopened containers at a temperature between 20°C to 28°C unless otherwise labeled. The shelf life of these materials is 12 months when stored in unopened containers at an average temperature of 25°C.
- Certifications and Compliance
- ISO 10993
- ISO 9001
- REACH (Europe)
- RoHS Compliant
- Ready to Use Product Features
- General Purpose
- Good Bonding Strength
- Good Thermal Stability
- Impact Resistance
- Low Viscosity
- Shock Resistant
- Vibration Damping
- Compatible Substrates and Surfaces
- Glass
- Metal
- Plastics
Technical data
Table 1 of 2
18 rows| Characteristic | Value | Unit |
|---|---|---|
| Specific Gravity | 1.1 | — |
| Hardness | 86 | Shore D |
| Lap Shear Strength to Aluminium (at -55°C) | 2300 | psi |
| Lap Shear Strength to Aluminium (at 25°C) | 3100 | psi |
| Lap Shear Strength to Aluminium (at 95°C) | 150 | psi |
| Die Shear Strength | 1800 | psi |
| Refractive Index | 1.5482 | — |
| Service Temperature Range | -55 to 125 | °C |
| Glass Transition Temperature (Tg) | 72 | °C |
| Coefficient of Linear Thermal Expansion (Below Tg) | 62 | 10⁻⁶/°C |
| Coefficient of Linear Thermal Expansion (Above Tg) | min. 200 | 10⁻⁶/°C |
| NASA Outgassing Data (TML) | 0.59 | % |
Table 2 of 2
3 rows| Characteristic | Value | Unit |
|---|---|---|
| Mix Ratio by Volumet (Resin/Hardener) | 2:1 | — |
| Mixed Viscosity (at 25°C) | 4,000 - 7,000 | cps |
| Pot Life (at 25°C, 100 grams) | 30 | hours |
