SetWORX™ 60
- Chemical Family
- Epoxy & Epoxy Derivatives
EPOXIBOND™ EB-135 is a clear epoxy adhesive designed for electronic, optical, medical, and general applications and for casting of small electrical components. This epoxy system has 2 to 1 mixing ratio by volume & cure fast at moderate temperature. The cured adhesive gives high impact and bond strength. It can be used for bonding glass, metals, woods and some plastics
Product families
Applications
- Industrial Adhesives & Sealants
- Industrial Manufacturing
Product Families
- Structural Adhesives
Other characteristics
- Brand
- SetWORX
- Product Type
- 2K (2 component) Adhesive
- Application Method
- Gun
- Compatible Substrates & Surfaces
- Metal, Plastics
- Markets
- Adhesives & Sealants
- Industrial
- Features
- High shear strength
- High peel strength
- 60 minute worklife
- BPA Free
- Non-hazardous shipping
- Outstanding environmental performance
- Easy mixing
- Shelf LIfe
- 12 Months
- Technology
- Ready-to-Use Products
- Packaging Type
- Cartridges
- Labeling Claims
- Bisphenol A-free
- Non-Hazardous
- Tin-free
- Application Methods
- Gun
- Curing
- Recommended Cure
- 24hrs at 25°C
- Alternate Cure
- 1 hr at 65°C
- Safety Information
- For Industrial Use Only
- Practices of good housekeeping, safety and cleanliness should be followed before, during and after use.
- Warning
- Adequate ventilation of work place and ovens is essential. These materials may cause injury to the skin following prolonged or repeated contact and dermatitis in susceptible individuals. In case of skin contact, wash thoroughly with soap and water. For eyes, flush immediately with plenty of water for at least 10 minutes and seek medical attention. Refer to Material Safety Data Sheet (MSDS) for additional health and safety information.
- Use Instructions
To use simply insert the cartridge into the application gun and start the plunger into the cylinders using light pressure on the trigger. Next, remove the cartridge cap and expel a small amount of adhesive to be sure both sides are flowing evenly and freely. If automatic mixing of resin and hardener is desired, attach the mixing nozzle to the end of the cartridge and begin dispensing the adhesive. For hand mixing, expel the desired amount of the adhesive and mix thoroughly. Mix approximately 15 seconds after uniform color is obtained.
- Shelf Life Storage
Product shall be ideally stored in a dry location in unopened containers at a temperature between 20°C to 28°C unless otherwise labeled. The shelf life of these materials is 12 months when stored in unopened containers at an average temperature of 25°C.
- Certifications and Compliance
- ISO 9001
- REACH (Europe)
- RoHS Compliant
- Ready to Use Product Features
- Easy Formulation
- Electrically Insulating
- General Purpose
- Good Peeling Strength
- Good Thermal Stability
- High Strength
- Impact Resistance
- Improved Shear Stability
- Compatible Substrates and Surfaces
- Metal
- Plastics
Technical data
Table 1 of 2
15 rows| Characteristic | Value | Unit |
|---|---|---|
| Specific Gravity | 1.1 | — |
| Hardness | 78 | Shore D |
| Lap Shear Strength to Aluminium (After 7days) | 4500 | psi |
| Lap Shear Strength to Stainless Steel (After 7days) | 4000 | psi |
| Lap Shear Strength to Copper (After 7days) | 4500 | psi |
| Lap Shear Strength to Brass (After 7days) | 4100 | psi |
| T-peel Strength to Aluminum (5-8mil bondline) | 50 | pli |
| Service Temperature Range | -55 to 120 | °C |
| Glass Transition Temperature (Tg) | 70 | °C |
| Coefficient of Linear Thermal Expansion (Below Tg) | 77 | 10⁻⁶/°C |
| Coefficient of Linear Thermal Expansion (Above Tg) | 195 | 10⁻⁶/°C |
| Dielectric Strength | 500 | Volts/mil |
Table 2 of 2
4 rows| Characteristic | Value | Unit |
|---|---|---|
| Viscosity (at 25°C) | 20,000 - 30,000 | cps |
| Mix Ratio by Weight (Resin/Hardener) | 2:1 | — |
| Mix Ratio by Volume (Resin/Hardener) | 2:1 | — |
| Pot Life (at 25°C, 20 grams) | 60 - 70 | minutes |
