ConoCrete Chemical & Food 115
- Chemical Family
- Epoxy & Epoxy Derivatives
ConoCrete Chemical & Food 115 is a chemically-resistant, 100% solids, aggregate-filled, epoxy floor system. It is ideal for resurfacing old and protecting new concrete floors from chemical and physical abuse. The physical properties of these materials far exceed those of concrete, providing a surface that not only has greater durability, but a chemical-resistant barrier to the substrate.
Other characteristics
- Brand
- ConoCrete
- Features
Acid Resistant, Chemical Resistant, Durable, Excellent Food Resistance, High Solids Content, Low VOC, Skid Resistant
- Product Type
- Mortar
- Application Area
- Masonry
- Application Method
- Trowel
- Compatible Substrates & Surfaces
- Concrete
- Markets
- Building & Construction
- Paints & Coatings
- Clean Up
All equipment should be cleaned with MEK before material cures. If removal is required after cure, consult Sauereisen for specific recommendations.
- Shelf LIfe
ConoCrete has a shelf life of one (1) year, when stored in unopened, tightly sealed containers in a dry location at 70°F. Avoid freezing. If there is a doubt as to the quality of the materials, consult a Sauereisen representative.
- Application
Primer - Primers are packaged in premeasured containers consisting of Hardener Part A and Resin Part B which must be mixed together before use. Remix the Part A and Part B before combining. Completely empty contents of Hardener Part A into Resin Part B container. Using a slow speed 1/2 inch drill motor with a "Jiffy" type blade, mix thoroughly for 3 minutes until blended to uniform color. Primer is ready for use immediately after mixing.; ConoCrete - Packaging consists of premeasured, unitized containers of Hardener Part A, Resin Part B, Aggregate Part C, and Pigment Part D. Remix Part A and B before combining.; Regular unit - Regular units are packaged in two 20 ft² batches. Completely empty contents of Pigment Part D and Resin Part B into a clean mixing container. Using a slow speed 1/2 inch drill motor affixed with a "Jiffy" type blade, mix thoroughly until blended to a uniform color. Add Hardener Part A to Resin/Pigment blend and mix for 2 minutes. Slowly add 2/3 of Aggregate Part C and mix until all material is wetted out. Then add remaining Aggregate and continue mixing until uniform in consistency.; Large unit - Completely empty contents of Pigment Part D into Resin Part B container. Using a slow speed 1/2 inch drill motor with a "Jiffy" type blade, mix thoroughly until blended to a uniform color.Completely add Hardener Part A to Resin/Pigment blend and mix for 2 minsutes. After mixing, add total contents into a 4-7ft³ mortar mixer and add three bags of Aggregate Part C. Mix for 3 minutes before adding fourth bag of Aggregate. Continue mixing until all material is wetted out and uniform in consistency. Mix only complete batches. Material which has begun to set must be discarded. Do not add any solvent, additive, or adulterant to the ConoCrete.
- Cure
- Heat Cure
Technical data
Table 1 of 1
11 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Application Time (Working Time, 70°F) | 30.0 | minutes | ASTM C-308 modified |
| Components | 4 part | — | — |
| Bond Strength to Concrete | Concrete Failure | — | ASTM D-4541 |
| Compressive Strength | 13135.88 | psi | ASTM C-579 |
| Density | 132.9 | pcf | ASTM C-905 |
| Flexural Strength | 6563.0 | psi | ASTM C-580 |
| Maximum Service Temperature | 150.0 | °F | — |
| Modulus of Elasticity | 2.2 x 10⁶ | psi | ASTM C-580 |
| Shrinkage | 0.058 | % | — |
| Tensile Strength (ASTM C-307) | 2798.0 | psi | — |
| Thickness | 2022-01-04 | inch | — |
