Creative Materials 122-07(SP)
- Chemical Family
- Epoxy & Epoxy Derivatives
122-07SP is a screen-printable, B-Stageable, highly thermally conductive, one part epoxy coating and adhesive. This system features excellent thermal stability, outstanding chemical resistance and excellent high temperature properties. Applications include die attach adhesives, printed circuit board fabrication, advanced material composites, sealing and high performance coatings.\nFeatures\nExcellent Thermal Conductivity]\nOutstanding Printability
Product families
Applications
- Printed Circuit Boards (PCBs)
Product Families
- Conductive Adhesives
Other characteristics
- Product Type
1K (1 component) Adhesive, Conductive Adhesive, Epoxy Adhesive; 1K (1 component) Adhesive; Conductive Adhesive; Epoxy Adhesive
- Application Method
- Injection, Screen Coating
- Markets
- Electrical & Electronics
- Technology
- Ready-to-Use Products
- Procedure
Apply adhesive to substrate. Apply heat to advance curing to the non-tacky stage (when cooled to room temperature). A temperature of 125°C for 2 – 3 minutes is required (B-stage time is mass related). The user is encouraged to experiment for optimum drying time at a given temperature. Store on release liner to prevent contamination.
- Bonding Procedure
To use, carefully align parts to be bonded, apply uniform pressure to maintain location. Follow curing guidelines given above. Timing should start once adhesive and substrate reach curing temperature.
- Curing Guidelines
These temperatures and times are presented as a guide only. The end-user is encouraged to experiment to determine optimum curing schedule.
- Safety and Handling
Use with adequate ventilation.; Keep away from sparks and open flames.; Avoid prolonged contact with skin and breathing of vapors.; Wash with soap and water to remove fro skin.
- Application Methods
- Injection
- Screen Coating
- Handling
122-07(SP) is a one component epoxy system and is ready to use as received. Product should be stored frozen to maintain consistent flow properties. Allow 122-07(SP) to warm up to room temperature before opening container. Prior to using, mix thoroughly to re-suspend fillers. If needed, 122-07(SP) can be thinned with small amounts of Creative Materials' 113-12 thinner.
- Certifications and Compliance
- ISO 9001
- Ready to Use Product Features
- Chemical Resistant
- Excellent Coating Performance
- Good Thermal Conductivity
- Good Thermal Stability
- High Modulus
- High Temperature Performance
- Long Screen Life
- Printability
Technical data
Table 1 of 3
5 rows| Characteristic | Value | Unit |
|---|---|---|
| Pot Life | Latent | — |
| Conductivity | 5.5 | W/mK |
| Chloride | max. 10 | ppm. |
| Sodium Content | max. 10 | ppm. |
| Potassium Content | max. 10 | ppm. |
Table 2 of 3
5 rows| Characteristic | Value | Unit |
|---|---|---|
| Brookfield Viscosity - HAT Viscometer (at 10 rpm at 25°C) | 23000 | cps |
| Specific Gravity | 1.85 | water = 1 |
| Theoretical Coverage (at 0.001" Thickness) | 30 | in^2 |
| Screen Life | 8 | hrs |
| Solid Content | 87 | % |
Table 3 of 3
18 rows| Characteristic | Value | Unit |
|---|---|---|
| Thermal Conductivity | 5.5 | W/mK |
| Dielectric Strength | 440 | volts/mil |
| Volume Resistivity | 1 x 10^16 | ohms cm |
| Dielectric Constant (at 1 Hz) | 5.2 | — |
| Dielectric Factor (60 Hz) | 0.018 | — |
| Thermal Stability | Good to 325 | °C |
| Useful Temperature Range | -55 to 230 | ºC |
| Glass Transition Temperature (Tg) | 100 | ºC |
| Coefficient of Thermal Expansion below Tg | 29.5 x 10^-6 | in/in/ºC |
| Coefficient of Thermal Expansion above Tg | 13.5 x 10^-5 | in/in/°C |
| Dynamic Tensile Modulus (at -65°C) | 8780 | Mpa |
| Dynamic Tensile Modulus (at 25°C) | 6710 | Mpa |
