Perma-Joint™ Sealant/FS
Perma-Joint™ Sealant/FS is a dual cartridge system composed of a two-component, 100% solids polymer designed for applications where a resilient, fast-setting joint material is needed. The semi-clear, unpigmented material is packaged in a dual-cartridge system and comes with a 1/2” 30 elements static mixing nozzle and retainer nut. It is recommended for concrete and cement expansion joints in the general industry.
Product families
Applications
- Sealants & Caulks
Product Families
- Caulks & Sealants
Other characteristics
- Brand
- Perma-Joint
- Product Type
2K (2 component) Sealant, Solvent free (100% Solids) Sealant; 2K (2 component) Sealant; Solvent free (100% Solids) Sealant
- Compatible Substrates & Surfaces
- Concrete
- Markets
- Building & Construction
- Coverage
11-12 ft. (1/2" wide, 1/2" deep) at Tube (600 mL, 0.1558 gal.)
- Shelf LIfe
6 months, unopened and stored at room temperature
- Limitations
Do not point tubes upward after the mixing nozzle has been attached and product has been dispensed, this may cause material to flow back into the tubes and cause clogging.
- Precaution
Use with adequate ventilation.; Avoid contact with eyes, skin and clothing, wear gloves or protective creams - if skin contact occurs, wash at the first opportunity with soap and water.; Eye exposure or inhalation can result in serious medical problems - in the event of eye contact, immediately flush eyes with water and contact a physician.; Keep out of the reach of children.; For industrial use only.
- Technology
- Ready-to-Use Products
- Floor Cleaning
Some cleaners may affect the color of the floor installed.. Test each cleaner in a small, area, utilizing your cleaning technique before cleaning entires surface.
- Product Mixing
It is important that the material be mixed (shaken) before using to avoid soft spots.; Perma-Joint Sealant FS has a very short pot life of 1 - 2 minutes and should be applied continuously once opened to prevent the tip from becoming clogged.; Improper mixing may result in product failure.; To assemble, hold the tubes with tip facing upward.; Remove the closed-end on the cartridge system with a screwdriver.; Next, place the static mix nozzle over the tube set ends.; Finally, slip the screw collar over the tip and tighten on the tube set and place the tube set into the dual tube applicator.; Always dispense a small amount onto cardboard or another disposable surface to prevent non-mixed material from entering the joint.; Do not allow material to mix prior to dispensing as it will cure within 1 - 2 minutes.
- Packaging (Kit)
- 1 Tube
- Cs. 6 Tubes
- Cs. 12 Tubes
- Product Storage
Bring the material to normal room temperature before using.; Continuous storage should be above 55°F (13°C) to prevent crystallization.
- Curing Schedule
* Time varies depending on air temperature and humidity.
- Abrasion Resistance
18.2 mg loss at 1000 g total load, 1000 rev, CS17 wheel; ASTM D 5963
Technical data
Table 1 of 1
9 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Clean Up | Use Xylol | — | — |
| Hardness | 40 - 45 | Shore D | ASTM D 2240 |
| Tensile Strength | 1984.0 | psi | ASTM D 638 |
| Adhesion (Concrete Failure) | 410.0 | psi | ASTM D 4541 |
| VOC | max. 310 | g/l | — |
| Curing Schedule* (Pot Life, 70°F) | 1 - 2 | minutes | — |
| Curing Schedule* (Recoat/Topcoat, 70°F) | 1.0 | hours | — |
| Curing Schedule* (Light Foot Traffic, 70°F) | 1 - 3 | hours | — |
| Curing Schedule* (Full Cure, 70°F) | 3 - 5 | days | — |
