Westcoat EC-34 Epoxy Topcoat

Other characteristics

Features

Chemical Resistant, Excellent Substrate Adhesion, High Build, High Solids Content, High Strength, Low Odor, Medium Viscosity

Product Type

2K (2 component) Coating, Primer, Solventless & High Solids Coating, Top Coat

Application Area

Floor, Garage, Industrial Seamless Floors, Kitchen, Warehouses

Application Method

Brush, Roller, Spray, Trowel, Wipe

Usage

EC-34 epoxy is used to create industrial seamless floors in manufacturing plants, mechanical warehouses, industrial kitchens and garages.. It is best used as a filler coat, broadcast coat or topcoat.

Color

• Black
• Blue
• Green
• Grey
• Red
• Tan
• White
• Yellow

Mixing

Premix each component separately.; For color consistency, box all part A's. In a clean bucket, mix 2 parts A with 1 part B (by volume) of EC-34.; Mix thoroughly with a low speed (400-600 rpm) drill motor for 3-4 minutes.; Make sure to scrape the sides and bottom of the container during mixing.; After mixing is completed, remove material from container within 5 minutes, as epoxy will begin to generate heat.; Spread immediately onto the floor.; As product is spread out, you will have longer working time (10-15 minutes at 70°F).

Show in full

Markets

Building & Construction

Clean Up

Uncured material should be removed with an environmentally-safe solvent.; Cured material should be removed mechanically.

Coverage

Coverage will vary depending on condition of surface and desired thickness.

As a primer

300-500 square feet per gallon.

As a coating

100-300 square feet per gallon.

Dry Time

You may re-coat as soon as the surface is dry to touch or in about 4-8 hours (but not later than 24 hours).; Light foot traffic may be permitted in 8-10 hours, light vehicle traffic in 48 hours, heavy traffic in 3 days.; All times are based on average temperature of 70 degrees F and 50% humidity.; Cooler temperatures will increase drying time.

Show in full

Moisture

All concrete should be tested for moisture before applying a seamless coating.. If moisture emissions exceed 5 lbs/1000 square feet/24 hours (ASTM F1869) or if the relative humidity (RH) exceeds 75% (ASTM F2170), contact the manufacturer before application.

Pot Life

40 minutes (Gel Time, 150gm, 72°F)

PACKAGING

1.5 gal & 15 gal kits available.

Advantages

• USDA/FDA Compliant
• 100% Solids
• Medium Viscosity
• Chemical Resistant
• Convenient 2:1 Mix
• High Strength
• Pigmented
• Low Odor
• 2 more

Inspection

The surface must be structurally sound, clean, dry and free of grease, paint, oil, dust, curing agents, laitance or any foreign material that will prevent proper adhesion.; The concrete should be at least 2,500 PSI and porous or rough enough to allow the product to soak in.; A minimum of 28 days curing time is required on all concrete.; Prior to starting work, test existing concrete slab for efflorescence, moisture and hydrostatic pressure.

Show in full

Shelf LIfe

2 years in unopened packaging

Limitations

This product is designed for professional use only.; Be sure to measure and mix properly. Be aware of the pot life of mixed epoxy.; Do not apply when temperatures are below 50°F or above 90°F.; Hot or cold weather will affect dry times.; Epoxy must be cured for a minimum of 24 hours before coming in contact with water.; Skid-resistant additives are available, such as CA-30 or CA-31.; For interior use only unless protected by a UV-resistant coating.; Solvents may be required in cooler weather to lower viscosity and increase coverage of 100% solids.; Please check with local laws governing the use of solvents.; Do not allow Westcoat products to freeze.

Show in full