Aegis® H350ZI
Aegis® H350ZI resin is an unfilled ultra high-viscosity nylon 6 homopolymer with excellent processability and structural properties for profile extrusion. It combines strength, stiffness and toughness with superior heat, chemical and abrasion resistance.
Product families
- Polyamides
Other characteristics
- Brand
- Aegis®
- Polymer Name
- Polyamide 6 (PA 6)
- Processing Methods
- Extrusion, Profile Extrusion
- Technology
- Plastics
- Color
- White
- Material Features
- Abrasion Resistant
- Chemical Resistant
- Dimensional Stability
- Good Stiffness
- Heat Resistance
- High Melt Strength
- High Viscosity
- Extrusion Guidelines
Melt Viscosity vs. Temperature Polymer Melt Temperature: 220°C (428°F) Two main factors affect the melt viscosity (stiffness or fluidity of the melt): 1. The molecular weight (MW) of the resin: Higher MW resins will have a higher melt viscosity than lower MW resins. 2. Temperature of the melt for any given MW resin: Higher process temperatures will provide a more fluid melt viscosity than lower process temperatures.; Typical Profile Extruder Barrel Temperature settings 240-290 °C (464-554 °F); Note: The values in this data sheet are for natural color resins only. Colorants or other additives may alter some or all of these properties. The data listed here fall within the normal range of product properties, but should not be used to establish specification limits nor used alone as the basis of design.
- Processing Guidelines
Material Handling This product is supplied in sealed containers and drying prior to processing is not required. However, higher moisture is the primary cause of processing problems. If drying becomes necessary, a dehumidifying or desiccant dryer operating at 80°C (176°F) is recommended. Drying time is dependent on moisture level. Further information concerning safe handling procedures can be obtained from the Safety Data Sheet. Alternatively, please contact your AdvanSix representative.
- Plastics and Elastomers Processing Methods
- Extrusion
- Profile Extrusion
Technical data
Table 1 of 4
5 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Tensile Modulus (23°C (73°F)) | 2,616 (379,468) | MPa (psi) | ISO 527-2 |
| Tensile Strength (23°C (73°F)) | 96 (13,926) | MPa (psi) | ISO 527-2 |
| Elongation at Yield (23°C (73°F)) | 5.63 | % | ISO 527-2 |
| Elongation at Break (at 23°C (73°F)) | 46.3 | % | ISO 527-2 |
| Notched Izod impact (at 23°C (73°F)) | 1.294 | ft-lbf/in | ASTM D-256 |
Table 2 of 4
6 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Viscosity, FAV | 400 | — | ASTM D-789 |
| RV (at 96% Sulfuric Acid, RV calculated from FAV) | 5.3 | — | ASTM D-789 |
| Extractable Content | max. 0.9 | % | SOP-702-307 |
| Specific Gravity (at 23°C (73°F)) | 1.13 | — | ASTM D-792 |
| Melt Flow Rate (at 280°C (536°F), 2.16Kg) | 2.6 | g/10 min | Internal SOP |
| Moisture Content | max. 0.12 | % | ASTM D-6869 |
Table 3 of 4
1 row| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Melting Point | 220°C (428°F) | °C (°F) | ASTM D-3418 |
Table 4 of 4
1 row| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Pellet Size | 0.834 | g/100 pellets | Internal SOP |
