Aegis® PIR-H8202NLB
- Chemical Family
- Polyamides
Aegis® PIR-H8202NLB resin from AdvanSix contains 100% post-industrial recycled (PIR) raw materials while providing the same top performance and processability as Aegis® H8202NLB, its standard, non-recycled counterpart.Aegis® PIR-H8202NLB resin is an unfilled, low/medium viscosity, non-lubricated, nylon 6 homopolymer. It exhibits good strength, stiffness, and toughness as well as excellent heat, chemical and abrasion resistance.
Properties
- Physical Form
- Pellets
- Solid
Product families
Applications
- Consumer Goods — Other Consumer Goods Applications; Consumer Goods — Sports & Recreation
- Aftermarket Parts & Components
- Interior
- Powertrain & UTH
- Equipment & Parts
- Automotive Electronics
- Other Devices & Assemblies
Product Families
- Recycled Polymers
- Polyamides
Other characteristics
- Brand
- Aegis® PIR
- Density
- 1,130.0 kg/m³
- Polymer Name
- Polyamide 6 (PA 6)
- Labeling Claims
- Contains PIR Resin, Recycled, Sustainable
- Contains PIR Resin
- Recycled
- Sustainable
- Processing Methods
- Compounding, Injection Molding
- Note
Aegis® PIR-H8202NLB is an unfilled, low/medium viscosity, non-lubricated, nylon 6 injection molding homopolymer exhibiting excellent melt fluidity for filling thin sections. It exhibits good strength, stiffness, and toughness as well as excellent heat, chemical and abrasion resistance
- Markets
- Automotive & Transportation
- Consumer Goods
- Electrical & Electronics
- Industrial
- Technology
- Plastics
- Material Features
- Abrasion Resistant
- Chemical Resistant
- Excellent Melt Flow
- Good Stiffness
- Good Strength
- Heat Resistance
- Homopolymer
- Improved Toughness
- Processing Guidelines
Material Handling. Aegis® PIR-H8202NLB is supplied in sealed containers and drying prior to processing is not required. However, higher moisture is the primary cause of processing issues. If drying becomes necessary, a dehumidifying or desiccant dryer operating at 80°C (176°F) is recommended. Drying time is dependent on moisture level. More information about safe handling procedures can be obtained by requesting the Safety Data Sheet.
- Injection Molding Guidelines
Typical Profile; Melt Temperature: 240-280°C (464-536°F) Mold Temperature: 80-95°C (176-203°F) Injection and Packing Pressure: 35-125 bar (500-1500 psi); Mold Temperatures; A mold temperature of 80-95°C (176-203°F) is recommended, but temperatures as low as 10°C (50°F) can be used where applicable.; Pressures; Injection pressure controls the filling of the part and should not be applied for 90% of ram travel. Packing pressure affects the final part and can be used effectively in controlling sink marks and shrinkage. It should be applied and maintained until the gate area is completely frozen off.; Fill Rate; Fast fill rates are recommended to ensure uniform melt delivery to the cavity and to prevent premature freezing.; Note: The values in this data sheet are for natural color resins only. Colorants or other additives may alter some or all of these properties. The data listed here fall within the normal range of product properties, but should not be used to establish specification limits nor used alone as the basis of design.
- Plastics and Elastomers End Uses
- Automotive Applications
- Electrical/Electronic Applications
- Gears
- Industrial Applications
- Levers
- Plastics and Elastomers Functions
- Resin
- Plastics and Elastomers Processing Methods
- Compounding
- Injection Molding
Technical data
Table 1 of 5
4 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Rockwell Hardness | 119 | Scale R | ASTM D-785 |
| Density | 1.13 | g/cm³ | ASTM D-792 |
| Melt Flow Rate (at 235°C/1.0 kg or 455°F/1.0 kg) | 9.8 | g/10 min | ASTM D-1238 |
| Mold Shrinkage Linear Flow | 1.28 | % | ASTM D-955 |
Table 2 of 5
6 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Elongation at Break (at 73°F (22.7°C) | 55 | % | ASTM D-638 |
| Elongation Yield (73°F (22.7°C), 50% RH) | 4 | % | ASTM D-638 |
| Flexural Modulus (at 73°F (22.7°C) | 3,010 (436,000) | MPa (psi) | ASTM D-790 |
| Flexural Strength (at 73°F (22.7°C) | 110 (15,900) | MPa (psi) | ASTM D-790 |
| Tensile Modulus (at 73°F (23°C)) | 2,850 (413,500) | MPa (psi) | ASTM D-638 |
| Tensile Strength Yield (73°F (22.7°C), 50% RH) | 79 (11,500) | MPa (psi) | ASTM D-638 |
Table 3 of 5
4 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Coefficient of Linear Thermal Expansion | 83 | μm/mm °C | ASTM D-831 |
| Heat Deflection (at 264 psi (1.8 MPa)) | 65 (149) | °C (°F) | ASTM D-648 |
| Heat Deflection (at 66 psi (0.45 MPa)) | 178 (352) | °C (°F) | ASTM D-648 |
| Melting Point | 220 (428) | °C (°F) | ASTM D-3418 |
Table 4 of 5
7 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| 96% SAV | 2.61 | — | — |
| Extractable Content | max. 0.8 | % | SOP-702-307 |
| Moisture (24 Hour) | 1.6 | % | ASTM D-570 |
| Moisture (50% RH) | 2.7 | % | ASTM D-570 |
| Moisture (Saturation) | 9.5 | % | ASTM D-570 |
| Moisture Content | max. 0.10 | % | ASTM D-6869 |
| Viscosity (FAV) | 49±3 | — | ASTM D-789 |
Table 5 of 5
2 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Notched Izod Impact (at -40°F (-40°C)) | 50 (0.9) | J/m (ft-lbs/in) | J/m (ft-lbs/in) |
| Notched Izod Impact (at 73°F (23°C)) | 60 (1.1) | J/m (ft-lbs/in) | J/m (ft-lbs/in) |
