epsotech PE HA1 NC
- Chemical Family
- PolyethylenesPolyolefins
Epsotech PE HA1 NC is a single layer high density Polyethylene product. It is specially formulated and manufactured for fabrication applications.
Properties
- Physical Form
- Sheets
Product families
- Agriculture & Feed — Other Agriculture & Feed Applications; Consumer Goods — Sports & Recreation
- Exterior & Body
- Technical Fabrics
- Other Medical Applications
- Marine
Other characteristics
- Brand
- epsotech
- Density
- 960.0 - 960.0 kg/m³
- Features
Acid Resistant, Alcohol Resistant, Alkali Resistant, Freeze Resistant, Impact Resistance, Low Moisture Absorption
- Polymer Name
- High Density Polyethylene (HDPE)
- Tensile Modulus
- 950.0 - 950.0 MPa
- Notes
Unless otherwise stated, products are tested at a typical thickness of 4mm * The density quoted should only be used as a guide. This value can change depending upon the type and quantity of pigments or additives used. ** Fire behavior values given by raw material supplier or by indicative test on raw material. Not intended as a specification
- Markets
- Agriculture & Feed
- Automotive & Transportation
- Consumer Goods
- Healthcare & Pharma
- Industrial
- Flame Rating
- UL 94 HB
- Technology
- Plastics
- Product Families
- Plastics — Parts, Shapes & Films
- Composites End Use
- Profiles
- Material Features
- Acid Resistant
- Alcohol Resistant
- Alkali Resistant
- Freeze Resistant
- Impact Resistance
- Low Moisture Absorption
- Storage and Drying
HDPE has a very low moisture absorption, therefore pre-drying is not normally required.
- Product Modification
Product code nomenclature takes in to account selected primary features of a product. The suffix may indicate a primary additional functionality, however, further multiple modifications are almost always possible and may be agreed upon and specified prior to our technical and commercial offer. Such enhancements are a normal part of our service capability and they do not affect the general characteristics listed in technical datasheets.
- Dimensional Tolerances
Standard tolerances are subject to the local standard tolerance set. Extra tolerance requirements may be possible on request and by special agreement
- Supplemental Information
Chemical Contact and cleaning. Chemical resistance is influenced by many factors, including concentration, temperature, exposure time and material stress. Therefore the data should only be used as a guide. Most common mild soaps or detergents dissolved in warm water can be used to effectively clean general dirt and surface contaminants, but in all cases should be objectively tested. Abrasive products will damage the surface.
- Certifications and Compliance
- UL 94
- Plastics and Elastomers End Uses
- Door Profiles
- Geotextiles
- Marine Applications
- Sporting Goods
- Wheel Housing Parts
Technical data
Table 1 of 3
4 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Tensile Modulus (23°C, 1mm/min) | 950.0 | MPa | ISO 527 |
| Yield Stress (23°C, 50mm/min) | 24.0 | MPa | ISO 527 |
| Elongation at Yield (23°C, 50mm/min) | 9.0 | % | ISO 527 |
| Charpy (Notched, 23°C, 1eA) | 15.0 | KJ/m² | ISO 179 |
Table 2 of 3
3 rows| Characteristic | Value | Unit |
|---|---|---|
| Density* | 0.96 | g/cm³ |
| UV Stabilisation (According to Customer Requirement) | Optional | — |
| Flammability Rating UL** | HB** | — |
Table 3 of 3
1 row| Characteristic | Value | Unit | Method |
|---|---|---|---|
| VICAT Softening Point (B/50) | 79.0 | °C | ISO 306 |
