Fine-L-Kote UR Urethane Conformal Coating
- Chemical Family
- Urethanes
Fine-L-Kote UR Urethane Conformal Coating is a Techspray® product that comes in a variety of coating formulas to meet field and engineering requirements. Specifications are generally determined by the type of protection required. Thermal, moisture, and static resistance, for example. Coatings contain Opti/Scan to allow quality control inspection of coating coverage and evenness on a PCB. When a coated board is exposed to a common, low-cost UV (short-wave black) light, the coated areas glow. The thicker the coating, the brighter the glow.
Properties
- Physical Form
- Liquid
Product families
Applications
- Electronics Coatings
- Printed Circuit Boards (PCBs)
Product Families
- Protective Coatings
Other characteristics
- Brand
- Fine-L-Kote
- Features
Abrasion Resistant, Chemical Resistant, Excellent Moisture Resistance, Good Thermal Stability, UV Detectable
- Product Type
- Conformal Coating
- Application Area
- Printed Electronics
- Application Method
- Brush, Dip Coating, Spray
- Odor
- Aromatic
- Markets
- Electrical & Electronics
- Shelf LIfe
- 1 Year
- Cure
- Heat Cure
- Technology
- Ready-to-Use Products
- Specifications
- • IPC-CC-830B
- Quality Standards
- IPC-CC-830B
- Application Methods
- Brush
- Dip Coating
- Spray
- Usage Instruction
Spray Application: Apply top to bottom, allowing coating to flow evenly around components. Rotate PCB 90º and repeat application. Rotate and apply coating two additional times, then allow board to cure. If additional thickness is desired, apply additional coatings. When using liquid spray with automatic dispensing equipment, adjustments may be required in application rate and viscosity. Dip Application: Using automatic equipment or hand immersion technique, slowly immerse PCB into the coating and remove slowly. Use an average rate of approximately 1 foot per minute. After allowing the board to cure, process may be repeated to achieve desired thickness. Brush Application: Evenly apply coating to areas desired at thickness required. Allow time for curing before reapplying to achieve a thick coating. Use WonderMASK to protect components during conformal coating process. After application, cured Fine-L-KoteTM may be removed using Techspray Conformal Coating Removal Pen (2510-N or 2510-P).
- Environmental Policy
Techspray® is committed to developing products to ensure a safer and cleaner environment. We will continue to meet and sustain the regulations of all federal, state and local government agencies.
- Benefits and Features
• Moisture resistant • Chemically resistant • Abrasion resistant • UL94 V-0 – nonflammable final coat • IPC-CC-830B qualified • UV indicator for black light QC inspection
- Certifications and Compliance
- UL 94
- Ready to Use Product Features
- Abrasion Resistant
- Chemical Resistant
- Excellent Moisture Resistance
- Good Thermal Stability
- UV Detectable
Technical data
Table 1 of 2
6 rows| Characteristic | Value | Unit |
|---|---|---|
| Flash Point (Closed Cup) | 81.0 | ºF |
| Flammable Limits | Lower 1 | % |
| Flammable Limits | Upper 7 | % |
| Boiling/Condensation Point | 300.2 | º F |
| Relative Density | 0.93 | — |
| Volatility | 86.0 | % (w/w) |
Table 2 of 2
12 rows| Characteristic | Value | Unit |
|---|---|---|
| Thermal Resistant | 120.0 | °C |
| Dielectric Strength | 380.0 | volts/mil |
| Dielectric Strength | 380.0 | V/Mil |
| Cure Type | Thermal/Air | — |
| Tack Free Time | 15.0 | minutes |
| Accelerated Cure Time/Temperature (2 Step, 49°C) | 20.0 | minutes |
| Accelerated Cure Time/Temperature (2 Step, 82°C) | 30.0 | minutes |
| Ambient Cure Time | 24.0 | Hrs |
| Viscosity (Bulk) | 2022-10-20 | cps |
| Operating Temperature Range | -30 to 121 | °C |
| Insulation Resistance | 1.78 x 1016 | ohms |
| Coverage (1 mil dry film, 1 gal liquid, 81.8 m²) | 880.0 | ft² |
