Fine-L-Kote AR Acrylic Conformal Coating
- Chemical Family
- Acrylics & Acrylates
Techspray's AR Acrylic Conformal Coating is Fine-L-Kote AR Acrylic Conformal Coating. Acrylic Conformal Coating is a low-cost conformal coating for PCB protection. Fine-L-Kote AR is HAPs (Hazardous Air Pollutants) free, which means it does not contain common coating solvents such as Toluene, Xylene, and MEK. This improves the usability and safety of the coating.
Properties
- Physical Form
- Liquid
Product families
Applications
- Electronics Coatings
- Printed Circuit Boards (PCBs)
Product Families
- Protective Coatings
Other characteristics
- Brand
- Fine-L-Kote
- Features
Excellent Dielectric Properties, Fast Cure, High Gloss, Ozone Resistant
- Product Type
- Clearcoat, Conformal Coating
- Clearcoat
- Conformal Coating
- Application Area
- Measuring Instruments, Printed Electronics
- Measuring Instruments
- Printed Electronics
- Application Method
- Dip Coating, Spray
- Odor
- Characteristic
- Markets
- Electrical & Electronics
- Shelf LIfe
- 2 Years
- Technology
- Ready-to-Use Products
- Labeling Claims
- HAPs-free
- Methyl Ethyl Ketone free
- Toluene-free
- Xylene-free
- Quality Standards
- IPC-CC-830B
- Thinning/Removal
Techspray coatings can be thinned to meet production requirements using Conformal Coating Thinner (2105). Conformal Coating Remover (2510) is also available for rework and repair, although coating is often just burnt through in the soldering process for spot repairs.
- Application Methods
- Dip Coating
- Spray
- Usage Instruction
Surface to be coated should be thoroughly cleaned with a solvent such as Flux Remover G3® (1631). Surface must be completely dry before application of coating. Shake can well. Hold the board to be coated in a horizontal position and spray from top to bottom, holding the can four to six inches from surface. First, apply a light topical coating, then, after board has been fully coated, immediately apply a second heavier coat. Allow material to flow around the components. After application, invert can and spray until no liquid is expelled. Coating will be tack free in approximately 15 minutes; however, full cure requires 24 hours depending upon humidity. Complete removal can be achieved in 30 to 45 minutes by using the (2510) Conformal Coating Remover. Removal time depends upon temperature, thickness of coating and application.
- Environmental Policy
Techspray® is committed to developing products to ensure a safer and cleaner environment. We will continue to meet and sustain the regulations of all federal, state and local government agencies.
- Benefits and Features
• Fast Cure – Dry to Touch in 15 Minutes. • Thick Coating – One-Pass Application • Fast & Easy Rework & Repair • Meets IPC-CC-830 • Crystal Clear & Glossy Finish • Contains Opti/Scan™, UV Indicator for Black Light QC Inspection • Hazardous Air Pollutant Free: no MEK, Toluene or Xylene
- Ready to Use Product Features
- Excellent Dielectric Properties
- Fast Cure
- High Gloss
- Ozone Resistant
Technical data
Table 1 of 2
4 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Vapor Density (Air=1) | min. 1 | — | — |
| Boiling Point | 230.0 | º F | — |
| Flashpoint and Method | 39.9 | ºF | TAG CC |
| Heat Combustion | 7.169 | kJ/g | — |
Table 2 of 2
25 rows| Characteristic | Value | Unit |
|---|---|---|
| Product Benefits | Economical | — |
| Selective Spray System | Not recommended | — |
| Atomized Spray System | Acceptable | — |
| Dip | Acceptable | — |
| Aerosol Available | YES | — |
| Thermal Resistant | Acceptable | — |
| Moisture /Fungus Resistant | Acceptable | — |
| Chemical Resistant | Not recommended | — |
| Vibration Resistant | Acceptable | — |
| Ease of Rework | Excellent | — |
| 1 Aerosol Can (1.1M²) | 12.0 | ft² |
| Tack Free Time | 15.0 | minutes |
