LNP™ LUBRICOMP™ Compound HFG25Z

Chemical Family: Polyamides

SABIC's Specialties Business LNP LUBRICOMP HFG25Z compound is based on Nylon 11 resin containing 25% glass fiber and graphite. Added features of this grade include: Wear Resistant. This product does not contain PFAS intentionally added during SHPP’s manufacturing process and are not expected to contain unintentional PFAS impurities. Each user is responsible for evaluating the presence of unintentional PFAS impurities.

Product families

Applications

Consumer Goods — Appliances & Electronics
Consumer Goods — Lawn & Garden
Consumer Goods — Sports & Recreation

Building & Construction — Decorative Materials & Finishes

Artificial Turf

Electrical & Electronics — Devices & Assemblies

Consumer Electronics
Displays

Printing & Packaging — Packaging

Non-Food Consumer Packaging

Personal Care — Packaging & Accessories

Applicators & Accessories

Electrical & Electronics — Parts & Components

Connectors
Switches & Relays

Product Families

Plastics — Engineering & Specialty Polymers

Polyamides

Other characteristics

Brand: LNP™ LUBRICOMP™ Compound
Polymer Name: Polyamide 11 (PA 11)
Fillers Included: Glass Fiber, Graphite
Glass Fiber
Graphite
Flexural Modulus: 18200.0 - 18200.0 MPa
Additives Included: Lubricant (Graphite), Lubricant (Unspecified)
Lubricant (Graphite)
Lubricant (Unspecified)
Processing Methods: Extrusion, Injection Molding
Note: ᵍ Measurements made from Laboratory test Coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.; ⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.; ¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.
Markets: Building & Construction
Consumer Goods
Electrical & Electronics
Personal Care
Printing & Packaging
Technology: Plastics
Labeling Claims: No Added PFAS
Material Features: Electrically Conductive
Friction Resistant
Low Moisture Absorption
Lubricated
No Added PFAS
Non-Halogenated
Wear Resistant
Plastics and Elastomers End Uses: Appliances
Building Materials
Cell Phones
Commercial Appliance
Computer Components
Consumer Applications
Containers
Displays
Plastics and Elastomers Functions: Resin
Plastics and Elastomers Processing Methods: Extrusion
Injection Molding

Technical data

Table 1 of 5

12 rows

Characteristic	Value	Unit	Method
Density ¹¹	1.3	g/cm³	ISO 1183
Density ¹¹	1.3	g/cm³	ASTM D792
Mold Shrinkage (flow, 24 hrs) ᵍ ¹¹	0.4 - 0.6	%	ASTM D955
Mold Shrinkage (flow, 24 hrs) ᵍ ¹¹	0.47	%	ISO 294
Mold Shrinkage (xflow, 24 hrs) ᵍ ¹¹	0.8 - 1	%	ASTM D955
Mold Shrinkage (xflow, 24 hrs) ᵍ ¹¹	0.93	%	ISO 294
Moisture Absorption (at 23°C, 50% RH, 24hrs) ¹¹	0.1	%	ASTM D570
Wear Factor Washer ¹¹	58	10^-10 in^5-min/ft-lb-hr	ASTM D3702 Modified: Manual
Dynamic COF ¹¹	0.41	—	ASTM D3702 Modified: Manual
Static COF ¹¹	0.45	—	ASTM D3702 Modified: Manual
Mold Shrinkage (flow) ᵍ ¹¹	0.47	%	SABIC method
Mold Shrinkage (xflow) ᵍ ¹¹	0.93	%	SABIC method

Table 2 of 5

14 rows

Characteristic	Value	Unit	Method
Tensile Stress (Yield, 5 mm/min) ¹¹	76	MPa	ISO 527
Tensile Stress (Break, 5 mm/min) ¹¹	76	MPa	ISO 527
Tensile Strain (Yield, 5 mm/min) ¹¹	2.3	%	ISO 527
Tensile Strain (Break, 5 mm/min) ¹¹	2.4	%	ISO 527
Tensile Modulus (at 1 mm/min) ¹¹	6830	MPa	ISO 527
Flexural Strength (at 2 mm/min) ¹¹	352	MPa	ISO 178
Flexural Modulus (at 2 mm/min) ¹¹	18200	MPa	ISO 178
Tensile Stress (Yield, Type I, 5 mm/min) ¹¹	153	MPa	ASTM D638
Tensile Stress (Break, Type I, 5 mm/min) ¹¹	153	MPa	ASTM D638
Tensile Strain (Yield, Type I, 5 mm/min) ¹¹	2.8	%	ASTM D638
Tensile Strain (Break, Type I, 5 mm/min) ¹¹	2.8	%	ASTM D638
Tensile Modulus (at 5 mm/min) ¹¹	11030	MPa	ASTM D638

Table 3 of 5

10 rows

Characteristic	Value	Unit	Method
Heat Deflection Temperature/Bf (at 0.45 Mpa, Flatw 80104, sp=64mm) ¹¹	182	°C	ISO 75/Bf
Heat Deflection Temperature/Af (at 1.8 Mpa, Flatw 80104, sp=64mm) ¹¹	166	°C	ISO 75/Af
Coefficient of Thermal Expansion (at -40°C to 40°C, flow) ¹¹	0.000035	1/°C	ISO 11359-2
Coefficient of Thermal Expansion (at -40°C to 40°C, flow) ¹¹	0.0000342	1/°C	ASTM E831
Coefficient of Thermal Expansion (at -40°C to 40°C, xflow) ¹¹	0.000092	1/°C	ISO 11359-2
Coefficient of Thermal Expansion (at -40°C to 40°C, xflow) ¹¹	0.0000918	1/°C	ASTM E831
Coefficient of Thermal Expansion (at 23°C to 60°C, flow) ¹¹	0.000035	1/°C	ISO 11359-2
Coefficient of Thermal Expansion (at 23°C to 60°C, xflow) ¹¹	0.000092	1/°C	ISO 11359-2
Heat Deflection Temperature (at 0.45 MPa, 3.2 mm, Unannealed) ¹¹	182	°C	ASTM D648
Heat Deflection Temperature (at 1.82 MPa, 3.2mm, Unannealed) ¹¹	171	°C	ASTM D648

Table 4 of 5

6 rows

Characteristic	Value	Unit	Method
Izod Impact (Notched, 80104, at 23°C) ¹¹	7	kJ/m²	ISO 180/1A
Izod Impact (Unnotched, 80104, at 23°C) ¹¹	29	kJ/m²	ISO 180/1U
Multi-Axial Impact ¹¹	3	J	ISO 6603
Izod Impact (Notched, at 23°C) ¹¹	69	J/m	ASTM D256
Izod Impact (Unnotched, at 23°C) ¹¹	453	J/m	ASTM D4812
Instrumented Dart Impact Energy (Peak, at 23°C) ¹¹	15	J	ASTM D3763

Table 5 of 5