LNP™ STAT-KON™ Compound RX10004

Chemical Family: Polyamides

SABIC's Specialties Business LNP STAT-KON RX10004 compound is based on Nylon 6/6 resin containing carbon fiber and 40% glass fiber. Added features of this grade include: Electrically Conductive, Easy Molding. This product does not contain PFAS intentionally added during SHPP’s manufacturing process and are not expected to contain unintentional PFAS impurities. Each user is responsible for evaluating the presence of unintentional PFAS impurities.

Product families

Applications

Electrical & Electronics — Devices & Assemblies

Industrial Automation

Electrical & Electronics — Parts & Components

Semiconductor Manufacturing

Product Families

Plastics — Engineering & Specialty Polymers

Polyamides

Other characteristics

Brand: LNP™ STAT-KON™ Compound
Polymer Name: Polyamide 66 (PA 66)
Fillers Included: Carbon Fiber, Glass Fiber
Carbon Fiber
Glass Fiber
Flexural Modulus: 16900.0 - 16900.0 MPa
Processing Methods: Injection Molding
Note: ᵈ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding. Do NOT mix NORYL GTX* resin with other grades of NORYL* resins. Polystyrene and acrylic regrind are effective purging Materials. Use temperature range appropriate for particular purging resin. Regrind must also be dried. Maximum 25% regrind. Dry at recommended temperatures and times for optimum performance. Overdrying can cause loss of physical properties and/or create appearance defects. Do not exceed recommended basic drying time and temperature above or:\n4-8 hrs at 95°C (200°F), 10 hrs max\n6-12 hrs at 80°C (175°F), 16 hrs max\n8-16 hrs at 65°C (150°F), 24 hrs max\nAVOID air circulating tray ovens. Moisture levels in heated ambient air can exceed moisture level in the resin itself, causing moisture ABSORPTION not drying. Avoid melt temperature in excess of 300°C (575°F) and residence times over 6-8 minutes (may affect properties and/or appearance). Nozzle temperature controls assist in elimination of drool premature freeze-off. Shot sizes in excess of 50% barrel capacity can lead to difficulties in providing a consistent, homogenous plastic melt.; ᵍ Measurements made from Laboratory test Coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.; ⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.; ¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.
Markets: Electrical & Electronics
Technology: Plastics
Labeling Claims: No Added PFAS
Material Features: Easy To Mold
Electrically Conductive
Good Moldability
Good Processability
High Modulus
High Stiffness
High Strength
Light Weight
Country Availability: Canada
China (Mainland)
Mexico
USA
Plastics and Elastomers End Uses: Electrical/Electronic Applications
Semiconductor Applications
Plastics and Elastomers Processing Methods: Injection Molding

Technical data

Table 1 of 5

5 rows

Characteristic	Value	Unit	Method
Tensile Stress (Yield, 5 mm/min) ¹¹	230	MPa	ISO 527
Tensile Strain (Break, 5 mm/min) ¹¹	2.8	%	ISO 527
Tensile Modulus (at 1 mm/min) ¹¹	18900	MPa	ISO 527
Flexural Stress (Yield, at 2 mm/min) ¹¹	334	MPa	ISO 178
Flexural Modulus (at 2 mm/min) ¹¹	16900	MPa	ISO 178

Table 2 of 5

2 rows

Characteristic	Value	Unit	Method
Mold Shrinkage (flow) ᵍ ¹¹	0.2 - 0.4	%	SABIC method
Density ¹¹	1.54	g/cm³	ISO 1183

Table 3 of 5

1 row

Characteristic	Value	Unit	Method
Surface Resistivity ᵈ ¹¹	100000 - 10000000	Ω	ASTM D257

Table 4 of 5