LNP™ LUBRICOMP™ Compound JX91198
- Chemical Family
- Polysulfones
SABIC's Specialties Business LNP LUBRICOMP JX91198 compound is based on Polyethersulfone (PES) resin containing 10% Carbon Fiber, 10% PTFE and proprietary lubricant. Added features of this grade include: Wear Resistant.
Product families
- High Performance Thermoplastics
Other characteristics
- Brand
- LNP™ LUBRICOMP™ Compound
- Polymer Name
- Polyethersulfone (PES)
- Fillers Included
Carbon Fiber, Carbon/Graphite/PTFE, Graphite, PTFE; Carbon Fiber; Carbon/Graphite/PTFE; Graphite; PTFE
- Flexural Modulus
- 8820.0 - 8820.0 MPa
- Additives Included
- Lubricant (Unspecified), Proprietary
- Lubricant (Unspecified)
- Proprietary
- Processing Methods
- Injection Molding
- Note
ᵍ Measurements made from Laboratory test Coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.; ⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.; ¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.
- Markets
- Building & Construction
- Consumer Goods
- Electrical & Electronics
- Personal Care
- Printing & Packaging
- Technology
- Plastics
- Product Features
- FM: 9.24 GPa
- HDT: 228°C
- Tight dimensional tolerance
- Superior wear and bearing performance
- Material Features
- Bearing Grade
- Friction Resistant
- High Temperature Resistance
- Lubricated
- Very Good Heat Resistance
- Wear Resistant
- Plastics and Elastomers End Uses
- Appliances
- Bearings
- Building Materials
- Cell Phones
- Commercial Appliance
- Computer Components
- Consumer Applications
- Containers
- Plastics and Elastomers Functions
- Resin
Technical data
Table 1 of 6
14 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Tensile Stress (Break, 5 mm/min) ¹¹ | 99 | MPa | ISO 527 |
| Tensile Stress (Break) ¹¹ | 116 | MPa | ASTM D638 |
| Tensile Stress (Break) ¹¹ | 112 | MPa | ISO 527 |
| Tensile Strain (Break, 5 mm/min) ¹¹ | 1.6 | % | ISO 527 |
| Tensile Strain (Break) ¹¹ | 1.9 | % | ASTM D638 |
| Tensile Strain (Break) ¹¹ | 1.8 | % | ISO 527 |
| Flexural Stress (Break, 2 mm/min) ¹¹ | 140 | MPa | ISO 178 |
| Tensile Modulus (at 50 mm/min) ¹¹ | 10130 | MPa | ASTM D638 |
| Flexural Modulus (at 2 mm/min) ¹¹ | 6300 | MPa | ISO 178 |
| Flexural Stress ¹¹ | 169 | MPa | ASTM D790 |
| Flexural Stress ¹¹ | 161 | MPa | ISO 178 |
| Flexural Modulus ¹¹ | 8820 | MPa | ASTM D790 |
Table 2 of 6
15 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Mold Shrinkage (on Tensile Bar, flow) ᵍ ¹¹ | 0.3 - 0.5 | % | SABIC method |
| Wear Factor Washer ¹¹ | 20 | 10^-10 in^5-min/ft-lb-hr | ASTM D3702 Modified: Manual |
| Wear Factor Washer ¹¹ | 4 | 10^-10 in^5-min/ft-lb-hr | ASTM D3702 Modified: Manual |
| Dynamic COF ¹¹ | 0.43 | — | ASTM D3702 Modified: Manual |
| Dynamic COF ¹¹ | 0.34 | — | ASTM D3702 Modified: Manual |
| Static COF ¹¹ | 0.34 | — | ASTM D3702 Modified: Manual |
| Static COF ¹¹ | 0.27 | — | ASTM D3702 Modified: Manual |
| Density ¹¹ | 1.5 | g/cm³ | ISO 1183 |
| Density ¹¹ | 1.5 | g/cm³ | ASTM D792 |
| Moisture Absorption (at 23°C, 50% RH, 24hrs) ¹¹ | 0.41 | % | ASTM D570 |
| Mold Shrinkage (flow, 24 hrs) ᵍ ¹¹ | 0.2 | % | ASTM D955 |
| Mold Shrinkage (flow, 24 hrs) ᵍ ¹¹ | 0.17 | % | ISO 294 |
Table 3 of 6
2 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Heat Deflection Temperature (at 1.82 MPa, 3.2mm, Unannealed) ¹¹ | 211 | °C | ASTM D648 |
| Heat Deflection Temperature/Af (at 1.8 Mpa, Flatw 80*10*4, sp=64mm) ¹¹ | 228 | °C | ISO 75/Af |
Table 4 of 6
1 row| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Surface Resistivity ¹¹ | 100 - 100000 | Ω | ASTM D257 |
Table 5 of 6
8 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Izod Impact (Unnotched, 80*10*4, at 23°C) ¹¹ | 20 | kJ/m² | ISO 180/1U |
| Izod Impact (Unnotched, 80*10*4, at 23°C) ¹¹ | 26 | kJ/m² | ISO 180/1U |
| Izod Impact (Notched, 80*10*4, at 23°C) ¹¹ | 6 | kJ/m² | ISO 180/1A |
| Izod Impact (Notched, 80*10*4, at 23°C) ¹¹ | 7 | kJ/m² | ISO 180/1A |
| Izod Impact (Unnotched, at 23°C) ¹¹ | 331 | J/m | ASTM D4812 |
| Izod Impact (Notched, at 23°C) ¹¹ | 42 | J/m | ASTM D256 |
| Instrumented Dart Impact Energy (Peak, at 23°C) ¹¹ | 4 | J | ASTM D3763 |
| Multi-Axial Impact ¹¹ | 2 | J | ISO 6603 |
Table 6 of 6
10 rows| Characteristic | Value | Unit |
|---|---|---|
| Drying Temperature ⁷ | 120 - 150 | °C |
| Drying Time ⁷ | 4 | Hrs |
| Maximum Moisture Content ⁷ | 0.05 | % |
| Melt Temperature ⁷ | 355 - 370 | °C |
| Front - Zone 3 Temperature ⁷ | 370 - 380 | °C |
| Middle - Zone 2 Temperature ⁷ | 360 - 370 | °C |
| Rear - Zone 1 Temperature ⁷ | 345 - 355 | °C |
| Mold Temperature ⁷ | 140 - 150 | °C |
| Back Pressure ⁷ | 0.3 - 0.7 | MPa |
| Screw Speed ⁷ | 60 - 100 | rpm |
