To catalogue
LNP™ LUBRICOMP™ Compound UFL36AS
- Chemical Family
- Polyamides
SABIC's Specialties Business LNP LUBRICOMP UFL36AS compound is based on Polyphthalamide (PPA) resin containing 30% glass fiber, 15% PTFE. Added features of this grade include: Heat Stabilized, Internally Lubricated, Wear Resistant.
Product families
Applications
Applications
- Consumer Goods — Appliances & Electronics
- Consumer Goods — Lawn & Garden
Automotive & Transportation — Automotive
- Aftermarket Parts & Components
- Automotive Lighting
- Cooling & Climate
- Powertrain & UTH
Industrial — Chemical & Industrial Manufacturing
- Equipment & Parts
Electrical & Electronics — Devices & Assemblies
- Consumer Electronics
- Displays
Healthcare & Pharma — Medical
- Medical Devices & Assemblies
Electrical & Electronics — Parts & Components
- Semiconductor Manufacturing
- Sensors & Actuators
Product Families
Plastics — Engineering & Specialty Polymers
- Polyamides
Other characteristics
- Brand
- LNP™ LUBRICOMP™ Compound
- Polymer Name
- Polyphthalamide (PPA)
- Fillers Included
- Glass Fiber, PTFE
- Glass Fiber
- PTFE
- Flexural Modulus
- 10100.0 - 10100.0 MPa
- Additives Included
Heat Stabilizer, Lubricant (PTFE), Lubricant (Unspecified), Mold Release Agent; Heat Stabilizer; Lubricant (PTFE); Lubricant (Unspecified); Mold Release Agent
- Processing Methods
- Injection Molding
- Note
ᵍ Measurements made from Laboratory test Coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.; ⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.; ¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.
- Markets
- Automotive & Transportation
- Consumer Goods
- Electrical & Electronics
- Healthcare & Pharma
- Industrial
- Technology
- Plastics
- Material Features
- Friction Resistant
- Good Mold Release
- Heat Stabilized
- High Stiffness
- High Strength
- High Temperature Resistance
- Lubricated
- Very Good Heat Resistance
- Plastics and Elastomers End Uses
- Air Intake Manifolds
- Amusement Machine
- Appliances
- Automotive Applications
- Automotive Gears
- Automotive Under The Hood
- Bearings
- Building Materials
- Plastics and Elastomers Functions
- Resin
- Plastics and Elastomers Processing Methods
- Injection Molding
Technical data
Table 1 of 5
13 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Specific Gravity ¹¹ | 1.58 | — | ASTM D792 |
| Moisture Absorption (at 23°C, 50% RH, 24hrs) ¹¹ | 0.1 - 0.2 | % | ASTM D570 |
| Water Absorption (at 23°C, 24hrs) ¹¹ | 0.3 - 0.4 | % | ASTM D570 |
| Water Absorption (at 23°C, 24hrs) ¹¹ | 0.3 - 0.4 | % | ISO 62-1 |
| Melt Flow Rate (at 340°C, 1.2 kgf) ¹¹ | 28 | g/10 min | ASTM D1238 |
| Dynamic COF ¹¹ | 0.51 | — | ASTM D3702 Modified: Manual |
| Static COF ¹¹ | 0.57 | — | ASTM D3702 Modified: Manual |
| Wear Factor Washer ¹¹ | 5 | 10^-10 in^5-min/ft-lb-hr | ASTM D3702 Modified: Manual |
| Density ¹¹ | 1.58 | g/cm³ | ISO 1183 |
| Moisture Absorption (at 23°C, 50% RH) ¹¹ | 0.1 - 0.2 | % | ISO 62 |
| Melt Volume Rate (at 340°C, 1.2 kg) ¹¹ | 24 | cm³/10 min | ISO 1133 |
| Mold Shrinkage (flow) ᵍ ¹¹ | 0.2 - 0.4 | % | SABIC method |
Table 2 of 5
29 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Tensile Modulus (at 5 mm/min) ¹¹ | 11200 | MPa | ASTM D638 |
| Tensile Strain (Break, Type I, 5 mm/min) ¹¹ | 1.7 | % | ASTM D638 |
| Tensile Stress (Break, Type I, 5 mm/min) ¹¹ | 189 | MPa | ASTM D638 |
| Flexural Modulus (at 1.3 mm/min, 50 mm span) ¹¹ | 9900 | MPa | ASTM D790 |
| Flexural Strength (at 1.3 mm/min, 50 mm span) ¹¹ | 250 | MPa | ASTM D790 |
| Tensile Modulus (at 1 mm/min) ¹¹ | 11500 | MPa | ISO 527 |
| Tensile Strain (Break, 5 mm/min) ¹¹ | 2.3 | % | ISO 527 |
| Tensile Stress (Break, 5 mm/min) ¹¹ | 188 | MPa | ISO 527 |
| Flexural Modulus (at 2 mm/min) ¹¹ | 10100 | MPa | ISO 178 |
| Flexural Modulus (at 2 mm/min, 80°C) ¹¹ | 8400 | MPa | ISO 178 |
| Flexural Modulus (at 2 mm/min, 100°C) ¹¹ | 7600 | MPa | ISO 178 |
| Flexural Modulus (at 2 mm/min, 120°C) ¹¹ | 5400 | MPa | ISO 178 |
Table 3 of 5
12 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Heat Deflection Temperature (at 1.82 MPa, 3.2mm, Unannealed) ¹¹ | 283 | °C | ASTM D648 |
| Vicat Softening Temperature (Rate B/50) ¹¹ | 262 | °C | ASTM D1525 |
| Vicat Softening Temperature (Rate B/50) ¹¹ | 262 | °C | ISO 306 |
| Coefficient of Thermal Expansion (at -30°C to 30°C, flow) ¹¹ | 0.000021 | 1/°C | ASTM D696 |
| Coefficient of Thermal Expansion (at -30°C to 30°C, xflow) ¹¹ | 0.000045 | 1/°C | ASTM D696 |
| Thermal Conductivity ¹¹ | 0.24 | W/m-K | ASTM D5930 |
| Specific Heat ¹¹ | 1722 | J/kg-K | ASTM E1269 |
| Heat Deflection Temperature/Af (at 1.8 Mpa, Flatw 80*10*4, sp=64mm) ¹¹ | 275 | °C | ISO 75/Af |
| Heat Deflection Temperature/Bf (at 0.45 Mpa, Flatw 80*10*4, sp=64mm) ¹¹ | 293 | °C | ISO 75/Bf |
| Vicat Softening Temperature (Rate B/120) ¹¹ | 258 | °C | ISO 306 |
| Coefficient of Thermal Expansion (at 23°C to 60°C, flow) ¹¹ | 0.000022 | 1/°C | ISO 11359-2 |
| Coefficient of Thermal Expansion (at 23°C to 60°C, xflow) ¹¹ | 0.000058 | 1/°C | ISO 11359-2 |
Table 4 of 5
9 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Izod Impact (Notched, at 23°C) ¹¹ | 90 | J/m | ASTM D256 |
| Izod Impact (Unnotched, at 23°C) ¹¹ | 730 | J/m | ASTM D4812 |
| Instrumented Dart Impact Total Energy (at 23°C) ¹¹ | 8 | J | ASTM D3763 |
| Izod Impact (Notched, 80*10*3, at -40°C) ¹¹ | 9 | kJ/m² | ISO 180/1A |
| Izod Impact (Notched, 80*10*4, at 23°C) ¹¹ | 10 | kJ/m² | ISO 180/1A |
| Izod Impact (Unnotched, 80*10*4, at 23°C) ¹¹ | 50 | kJ/m² | ISO 180/1U |
| Izod Impact (Unnotched, 80*10*4, at -40°C) ¹¹ | 45 | kJ/m² | ISO 180/1U |
| Charpy Impact (at 23°C, V-notch Edgew 80*10*4 sp=62mm) ¹¹ | 12 | kJ/m² | ISO 179/1eA |
| Charpy Impact (at 23°C, Unnotch Edgew 80*10*4 sp=62mm) ¹¹ | 55 | kJ/m² | ISO 179/1eU |
Table 5 of 5
10 rows| Characteristic | Value | Unit |
|---|---|---|
| Drying Temperature ⁷ | 120 - 150 | °C |
| Drying Time ⁷ | 4 | Hrs |
| Maximum Moisture Content ⁷ | 0.15 | % |
| Melt Temperature ⁷ | 315 - 330 | °C |
| Rear - Zone 1 Temperature ⁷ | 310 - 320 | °C |
| Middle - Zone 2 Temperature ⁷ | 315 - 325 | °C |
| Front - Zone 3 Temperature ⁷ | 325 - 340 | °C |
| Mold Temperature ⁷ | 150 - 170 | °C |
| Back Pressure ⁷ | 0.2 - 0.3 | MPa |
| Screw Speed ⁷ | 30 - 60 | rpm |
