To catalogue
LNP™ LUBRICOMP™ Compound RL004
- Chemical Family
- Polyamides
LNP LUBRICOMP RL004 compound is based on Nylon 6/6 resin containing 20% PTFE. Added features of this grade include: Wear Resistant
Product families
Applications
Applications
- Consumer Goods — Appliances & Electronics
- Consumer Goods — Lawn & Garden
- Consumer Goods — Sports & Recreation
Building & Construction — Decorative Materials & Finishes
- Artificial Turf
Electrical & Electronics — Devices & Assemblies
- Consumer Electronics
- Displays
Printing & Packaging — Packaging
- Healthcare Packaging
- Non-Food Consumer Packaging
Personal Care — Packaging & Accessories
- Applicators & Accessories
Electrical & Electronics — Parts & Components
- Connectors
- Switches & Relays
Product Families
Plastics — Engineering & Specialty Polymers
- Polyamides
Other characteristics
- Brand
- LNP™ LUBRICOMP™ Compound
- Polymer Name
- Polyamide 66 (PA 66)
- Fillers Included
- PTFE
- Flexural Modulus
- 2500.0 - 2500.0 MPa
- Additives Included
Heat Stabilizer, Lubricant (PTFE), Mold Release Agent; Heat Stabilizer; Lubricant (PTFE); Mold Release Agent
- Processing Methods
- Injection Molding
- Note
ᵍ Measurements made from Laboratory test Coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.; ᵖ UL ratings shown on the technical datasheet might not cover the full range of thicknesses and colors. For details, please see the UL Yellow Card.; ⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.; ¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.
- Markets
- Building & Construction
- Consumer Goods
- Electrical & Electronics
- Personal Care
- Printing & Packaging
- Flame Rating
- UL 94 HB
- Technology
- Plastics
- Material Features
- Friction Resistant
- Good Mold Release
- Heat Stabilized
- Unreinforced
- Wear Resistant
- Certifications and Compliance
- UL 94
- Plastics and Elastomers End Uses
- Appliances
- Bearings
- Building Materials
- Cash Dispenser (ATM)
- Cell Phones
- Commercial Appliance
- Computer Components
- Consumer Applications
- Plastics and Elastomers Functions
- Resin
- Plastics and Elastomers Processing Methods
- Injection Molding
Technical data
Table 1 of 6
12 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Density ¹¹ | 1.25 | g/cm³ | ISO 1183 |
| Density ¹¹ | 1.25 | g/cm³ | ASTM D792 |
| Moisture Absorption (at 23°C, 50% RH, 24hrs) ¹¹ | 0.8 - 1.2 | % | ASTM D570 |
| Water Absorption (at 23°C, 24hrs) ¹¹ | 1 - 1.2 | % | ASTM D570 |
| Water Absorption (at 23°C, 24hrs) ¹¹ | 1 - 1.2 | % | ISO 62-1 |
| Dynamic COF ¹¹ | 0.27 | — | ASTM D3702 Modified: Manual |
| Static COF ¹¹ | 0.2 | — | ASTM D3702 Modified: Manual |
| Wear Factor Washer ¹¹ | 21 | 10^-10 in^5-min/ft-lb-hr | ASTM D3702 Modified: Manual |
| Moisture Absorption (at 23°C, 50% RH) ¹¹ | 0.8 - 1.2 | % | ISO 62 |
| Melt Volume Rate (at 275°C, 2.16 kg) ¹¹ | 24 - 32 | cm³/10 min | ISO 1133 |
| Mold Shrinkage (flow) ᵍ ¹¹ | 1 - 3 | % | SABIC method |
| Mold Shrinkage (xflow) ᵍ ¹¹ | 1 - 3 | % | SABIC method |
Table 2 of 6
19 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Tensile Modulus (at 5 mm/min) ¹¹ | 3000 | MPa | ASTM D638 |
| Tensile Strain (Break, Type I, 5 mm/min) ¹¹ | 6.7 | % | ASTM D638 |
| Tensile Stress (Break, Type I, 5 mm/min) ¹¹ | 71 | MPa | ASTM D638 |
| Flexural Modulus (at 1.3 mm/min, 50 mm span) ¹¹ | 2450 | MPa | ASTM D790 |
| Flexural Strength (at 1.3 mm/min, 50 mm span) ¹¹ | 91 | MPa | ASTM D790 |
| Hardness (Rockwell M) ¹¹ | 56 | — | ASTM D785 |
| Hardness (Rockwell R) ¹¹ | 110 | — | ASTM D785 |
| Tensile Modulus (at 1 mm/min) ¹¹ | 2900 | MPa | ISO 527 |
| Tensile Strain (Break, 5 mm/min) ¹¹ | 9.4 | % | ISO 527 |
| Tensile Stress (Break, 5 mm/min) ¹¹ | 65 | MPa | ISO 527 |
| Flexural Modulus (at 2 mm/min) ¹¹ | 2500 | MPa | ISO 178 |
| Flexural Modulus (at 2 mm/min, 60°C) ¹¹ | 1400 | MPa | ISO 178 |
Table 3 of 6
14 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Vicat Softening Temperature (Rate B/50) ¹¹ | 240 | °C | ASTM D1525 |
| Vicat Softening Temperature (Rate B/50) ¹¹ | 240 | °C | ISO 306 |
| Heat Deflection Temperature (at 0.45 MPa, 3.2 mm, Unannealed) ¹¹ | 239 | °C | ASTM D648 |
| Heat Deflection Temperature (at 1.82 MPa, 3.2mm, Unannealed) ¹¹ | 70 | °C | ASTM D648 |
| Coefficient of Thermal Expansion (at -30°C to 30°C, flow) ¹¹ | 0.00009 | 1/°C | ASTM D696 |
| Coefficient of Thermal Expansion (at -30°C to 30°C, xflow) ¹¹ | 0.000088 | 1/°C | ASTM D696 |
| Coefficient of Thermal Expansion (at 23°C to 60°C, flow) ¹¹ | 0.000097 | 1/°C | ISO 11359-2 |
| Coefficient of Thermal Expansion (at 23°C to 60°C, xflow) ¹¹ | 0.00012 | 1/°C | ISO 11359-2 |
| Heat Deflection Temperature/Af (at 1.8 Mpa, Flatw 80*10*4, sp=64mm) ¹¹ | 70 | °C | ISO 75/Af |
| Heat Deflection Temperature/Bf (at 0.45 Mpa, Flatw 80*10*4, sp=64mm) ¹¹ | 201 | °C | ISO 75/Bf |
| Vicat Softening Temperature (Rate B/120) ¹¹ | 230 | °C | ISO 306 |
| Relative Temperature Index (Electrical) ᵖ ¹¹ | 65 | °C | UL 746B |
Table 4 of 6
7 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Izod Impact (Notched, at 23°C) ¹¹ | 35 | J/m | ASTM D256 |
| Izod Impact (Unnotched, at 23°C) ¹¹ | 600 | J/m | ASTM D4812 |
| Instrumented Dart Impact Total Energy (at 23°C) ¹¹ | 4 | J | ASTM D3763 |
| Izod Impact (Notched, 80*10*4, at 23°C) ¹¹ | 5 | kJ/m² | ISO 180/1A |
| Izod Impact (Unnotched, 80*10*4, at 23°C) ¹¹ | 50 | kJ/m² | ISO 180/1U |
| Charpy Impact (at 23°C, V-notch Edgew 80*10*4 sp=62mm) ¹¹ | 5 | kJ/m² | ISO 179/1eA |
| Charpy Impact (at 23°C, Unnotch Edgew 80*10*4 sp=62mm) ¹¹ | 65 | kJ/m² | ISO 179/1eU |
Table 5 of 6
10 rows| Characteristic | Value | Unit |
|---|---|---|
| Drying Temperature ⁷ | 80 | °C |
| Drying Time ⁷ | 4 | Hrs |
| Maximum Moisture Content ⁷ | 0.15 - 0.25 | % |
| Melt Temperature ⁷ | 275 - 290 | °C |
| Rear - Zone 1 Temperature ⁷ | 265 - 275 | °C |
| Middle - Zone 2 Temperature ⁷ | 280 - 295 | °C |
| Front - Zone 3 Temperature ⁷ | 295 - 305 | °C |
| Mold Temperature ⁷ | 80 - 95 | °C |
| Back Pressure ⁷ | 0.2 - 0.3 | MPa |
| Screw Speed ⁷ | 30 - 60 | rpm |
Table 6 of 6
1 row| Characteristic | Value | Unit | Method |
|---|---|---|---|
| UL Recognized (94HB Flame Class Rating) ᵖ | 1.5 | mm | UL 94 |
