LNP™ LUBRICOMP™ Compound UL002S

Chemical Family: Polyamides

LNP LUBRICOMP UL002S compound is based on Polyphthalamide (PPA) resin containing 10% PTFE. Added features of this grade include: Heat Stabilized, Wear Resistant.

Product families

Applications

Consumer Goods — Appliances & Electronics

Automotive & Transportation — Automotive

Powertrain & UTH

Industrial — Chemical & Industrial Manufacturing

Equipment & Parts

Electrical & Electronics — Devices & Assemblies

Consumer Electronics
Displays

Electrical & Electronics — Parts & Components

Housings & Enclosures
Semiconductor Manufacturing

Product Families

Plastics — Engineering & Specialty Polymers

Polyamides

Other characteristics

Brand: LNP™ LUBRICOMP™ Compound
Polymer Name: Polyphthalamide (PPA)
Fillers Included: PTFE
Additives Included: Heat Stabilizer, Lubricant (PTFE)
Heat Stabilizer
Lubricant (PTFE)
Processing Methods: Injection Molding
Note: ᵍ Measurements made from Laboratory test Coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.; ⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.; ¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.; ᵖ UL ratings shown on the technical datasheet might not cover the full range of thicknesses and colors. For details, please see the UL Yellow Card.
Markets: Automotive & Transportation
Consumer Goods
Electrical & Electronics
Industrial
Flame Rating: UL 94 V2
Technology: Plastics
Product Features: HDT: 110°C,
Good balance of cost and performance
Low wear and COF
Material Features: Cost Effective
Heat Stabilized
High Performance
High Temperature Resistance
Low Coefficient of Friction
Unreinforced
Very Good Heat Resistance
Wear Resistant
Certifications and Compliance: UL 94
Plastics and Elastomers End Uses: Appliances
Automotive Applications
Automotive Under The Hood
Cell Phones
Commercial Appliance
Computer Components
Consumer Applications
Covers
Plastics and Elastomers Functions: Resin
Plastics and Elastomers Processing Methods: Injection Molding
Wear and Friction Solutions High Temperature Materials: Design engineer look to replace metal parts and components with thermoplastics whenever possible. Not only can they be produced more cost-effectively, they offer greater design flexibility, weigh less and resist corrosion. The availability of high temperature resins like PEEK, PPS, PPA and PEI can stretch the use of thermoplastic even further.; If you can't stand the heat… internally lubricated compounds: While auto under-the-hood and industrial machinery might be the first to come to mind, high temperature application are not always driven by hot operating environment. Some application that may never see elevated use temperatures have to survive a hot manufacturing environment (lead-free solder, paint ovens). High temperature generally feature good chemical resistance as well.; Internally lubricated compounds:; The addition of an internal lubricant to a thermoplastic material can improve the wear resistance and can reduce the coefficient of friction in plastic parts. Traditional lubricants like PTFE and PTFE/Si blends are common. Compounds made with high temperature resins can provide wear performance comparable with externally lubricated metal parts.

Technical data

Table 1 of 5

13 rows

Characteristic	Value	Unit	Method
Tensile Stress (Yield, Type I, 5 mm/min) ¹¹	60	MPa	ASTM D638
Tensile Stress (Break, Type I, 5 mm/min) ¹¹	60	MPa	ASTM D638
Tensile Strain (Yield, Type I, 5 mm/min) ¹¹	2.2	%	ASTM D638
Tensile Strain (Break, Type I, 5 mm/min) ¹¹	2.2	%	ASTM D638
Tensile Modulus (at 50 mm/min) ¹¹	3170	MPa	ASTM D638
Flexural Stress (Yield, 1.3 mm/min, 50 mm span) ¹¹	105	MPa	ASTM D790
Flexural Stress (Break, 1.3 mm/min, 50 mm span) ¹¹	105	MPa	ASTM D790
Flexural Modulus (at 1.3 mm/min, 50 mm span) ¹¹	2980	MPa	ASTM D790
Tensile Stress (Yield, 5 mm/min) ¹¹	58	MPa	ISO 527
Tensile Stress (Break, 5 mm/min) ¹¹	60	MPa	ISO 527
Tensile Strain (Yield, 5 mm/min) ¹¹	2.1	%	ISO 527
Tensile Strain (Break, 5 mm/min) ¹¹	2.2	%	ISO 527

Table 2 of 5

10 rows

Characteristic	Value	Unit	Method
Density ¹¹	1.26	g/cm³	ISO 1183
Density ¹¹	1.25	g/cm³	ASTM D792
Moisture Absorption (at 23°C, 50% RH, 24hrs) ¹¹	0.47	%	ASTM D570
Mold Shrinkage (flow, 24 hrs) ᵍ ¹¹	0.9 - 2	%	ASTM D955
Mold Shrinkage (xflow, 24 hrs) ᵍ ¹¹	0.7 - 0.9	%	ASTM D955
Wear Factor Washer ¹¹	20	10^-10 in^5-min/ft-lb-hr	ASTM D3702 Modified: Manual
Wear Factor Ring ¹¹	-1	10^-10 in^5-min/ft-lb-hr	ASTM D3702 Modified: Manual
Dynamic COF ¹¹	0.26	—	ASTM D3702 Modified: Manual
Static COF ¹¹	0.16	—	ASTM D3702 Modified: Manual
Moisture Absorption (at 23°C, 50% RH) ¹¹	0.73	%	ISO 62

Table 3 of 5

5 rows

Characteristic	Value	Unit	Method
Izod Impact (Unnotched, at 23°C) ¹¹	453	J/m	ASTM D4812
Izod Impact (Notched, at 23°C) ¹¹	26	J/m	ASTM D256
Instrumented Dart Impact Total Energy (at 23°C) ¹¹	2	J	ASTM D3763
Izod Impact (Unnotched, 80104, at 23°C) ¹¹	27	kJ/m²	ISO 180/1U
Izod Impact (Notched, 80104, at 23°C) ¹¹	2	kJ/m²	ISO 180/1A

Table 4 of 5