LNP™ LUBRICOMP™ Compound OFL36

Chemical Family: Polyphenylene Sulfide (PPS)

SABIC's Specialties Business LNP LUBRICOMP OFL36 compound is based on Polyphenylene Sulfide (PPS) - linear resin containing 30% glass fiber, 15% PTFE. Added features of this grade include: Wear Resistant.

Product families

Plastics — Engineering & Specialty Polymers

High Performance Thermoplastics

Other characteristics

Brand: LNP™ LUBRICOMP™ Compound
Polymer Name: Polyphenylene Sulfide (PPS)
Fillers Included: Glass Fiber, PTFE
Glass Fiber
PTFE
Flexural Modulus: 11050.0 - 11050.0 MPa
Additives Included: Lubricant (PTFE)
Processing Methods: Injection Molding
Note: ᵍ Measurements made from Laboratory test Coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.; ᵖ UL ratings shown on the technical datasheet might not cover the full range of thicknesses and colors. For details, please see the UL Yellow Card.; ⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.; ¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.
Markets: Building & Construction
Consumer Goods
Electrical & Electronics
Healthcare & Pharma
Industrial
Personal Care
Printing & Packaging
Flame Rating: UL 94 V0
Technology: Plastics
Product Features: FM: 11.1GPa
HDT:257°C
Chemical resistance
Low wear and COF
UL94-V0@0.75 mm,
Material Features: Chemical Resistant
Friction Resistant
High Stiffness
Low Coefficient of Friction
Wear Resistant
Certifications and Compliance: UL 94

Technical data

Table 1 of 7

18 rows

Characteristic	Value	Unit	Method
Tensile Stress (Break, Type I, 5 mm/min) ¹¹	124	MPa	ASTM D638
Tensile Stress (Break) ¹¹	145	MPa	ASTM D638
Tensile Stress (Break) ¹¹	124	MPa	ISO 527
Tensile Strain (Break, Type I, 5 mm/min) ¹¹	1.3	%	ASTM D638
Tensile Strain (Break) ¹¹	1.7	%	ASTM D638
Tensile Strain (Break) ¹¹	1.4	%	ISO 527
Tensile Modulus (at 50 mm/min) ¹¹	12600	MPa	ASTM D638
Flexural Stress (Break, 1.3 mm/min, 50 mm span) ¹¹	178	MPa	ASTM D790
Flexural Stress ¹¹	180	MPa	ISO 178
Flexural Stress ¹¹	200	MPa	ASTM D790
Flexural Stress ¹¹	197	MPa	ISO 178
Flexural Modulus (at 1.3 mm/min, 50 mm span) ¹¹	11600	MPa	ASTM D790

Table 2 of 7

15 rows

Characteristic	Value	Unit	Method
Density ¹¹	1.7	g/cm³	ASTM D792
Density ¹¹	1.7	g/cm³	ISO 1183
Moisture Absorption (at 23°C, 50% RH, 24hrs) ¹¹	0.01	%	ASTM D570
Mold Shrinkage (flow, 24 hrs) ᵍ ¹¹	0.1 - 0.2	%	ASTM D955
Mold Shrinkage (flow, 24 hrs) ᵍ ¹¹	0.13 - 0.18	%	ISO 294
Mold Shrinkage (xflow, 24 hrs) ᵍ ¹¹	0.6 - 0.8	%	ASTM D955
Mold Shrinkage (xflow, 24 hrs) ᵍ ¹¹	0.3 - 0.5	%	ASTM D955
Mold Shrinkage (xflow, 24 hrs) ᵍ ¹¹	0.3 - 0.48	%	ISO 294
Wear Factor Washer ¹¹	33	10^-10 in^5-min/ft-lb-hr	ASTM D3702 Modified: Manual
Wear Factor Washer ¹¹	52	10^-10 in^5-min/ft-lb-hr	ASTM D3702 Modified: Manual
Dynamic COF ¹¹	0.44	—	ASTM D3702 Modified: Manual
Static COF ¹¹	0.35	—	ASTM D3702 Modified: Manual

Table 3 of 7

14 rows

Characteristic	Value	Unit	Method
Heat Deflection Temperature (at 1.82 MPa, 3.2mm, Unannealed) ¹¹	266	°C	ASTM D648
Coefficient of Thermal Expansion (at -40°C to 40°C, flow) ¹¹	0.0000236	1/°C	ISO 11359-2
Coefficient of Thermal Expansion (at -40°C to 40°C, flow) ¹¹	0.0000234 - 0.00005003	1/°C	ASTM E831
Heat Deflection Temperature (at 0.45 MPa, 3.2 mm, Unannealed) ¹¹	278	°C	ASTM D648
Coefficient of Thermal Expansion (at -40°C to 40°C, xflow) ¹¹	0.0000486	1/°C	ASTM E831
Coefficient of Thermal Expansion (at -40°C to 40°C, xflow) ¹¹	0.0000501	1/°C	ISO 11359-2
Coefficient of Thermal Expansion (at -30°C to 30°C, flow) ¹¹	0.000025	1/°C	ASTM D696
Heat Deflection Temperature/Af (at 1.8 Mpa, Flatw 80104, sp=64mm) ¹¹	266	°C	ISO 75/Af
Heat Deflection Temperature/Af (at 1.8 Mpa, Flatw 80104, sp=64mm) ¹¹	257	°C	ISO 75/Af
Coefficient of Thermal Expansion (at -30°C to 30°C, xflow) ¹¹	0.000034	1/°C	ASTM D696
Relative Temperature Index (Electrical) ᵖ ¹¹	200	°C	UL 746B
Relative Temperature Index (Mechanical with impact) ᵖ ¹¹	130	°C	UL 746B

Table 4 of 7

7 rows

Characteristic	Value	Unit	Method
Comparative Tracking Index (UL, PLC) ᵖ ¹¹	4	PLC Code	UL 746A
Hot Wire Ignition (PLC 0) ᵖ ¹¹	min. 1.5	mm	UL 746A
High Ampere Arc Ignition (PLC 0) ᵖ ¹¹	min. 1.5	mm	UL 746A
Hot Wire Ignition (PLC 3) ᵖ ¹¹	min. 0.75	mm	UL 746A
High Voltage Arc Track Rate (PLC) ᵖ ¹¹	4	PLC Code	UL 746A
Arc Resistance (Tungsten, PLC) ¹¹	7	PLC Code	ASTM D495
High Ampere Arc Ignition (PLC 2) ᵖ ¹¹	min. 0.75	mm	UL 746A

Table 5 of 7

11 rows

Characteristic	Value	Unit	Method
Izod Impact (Unnotched, at 23°C) ¹¹	550	J/m	ASTM D4812
Izod Impact (Unnotched, at 23°C) ¹¹	416	J/m	ASTM D4812
Izod Impact (Notched, at 23°C) ¹¹	60	J/m	ASTM D256
Izod Impact (Notched, at 23°C) ¹¹	85	J/m	ASTM D256
Instrumented Dart Impact Energy (Peak, at 23°C) ¹¹	3	J	ASTM D3763
Multi-Axial Impact ¹¹	1	J	ISO 6603
Multi-Axial Impact ¹¹	2	J	ISO 6603
Instrumented Dart Impact Total Energy (at 23°C) ¹¹	11	J	ASTM D3763
Izod Impact (Unnotched, 80104, at 23°C) ¹¹	25	kJ/m²	ISO 180/1U
Izod Impact (Notched, 80104, at 23°C) ¹¹	5	kJ/m²	ISO 180/1A
Izod Impact (Notched, 80104, at 23°C) ¹¹	9	kJ/m²	ISO 180/1A

Table 6 of 7

9 rows

Characteristic	Value	Unit
Drying Temperature ⁷	120 - 150	°C
Drying Time ⁷	4	Hrs
Melt Temperature ⁷	315 - 320	°C
Front - Zone 3 Temperature ⁷	330 - 345	°C
Middle - Zone 2 Temperature ⁷	320 - 330	°C
Rear - Zone 1 Temperature ⁷	305 - 315	°C
Mold Temperature ⁷	140 - 165	°C
Back Pressure ⁷	0.2 - 0.3	MPa
Screw Speed ⁷	30 - 60	rpm

Table 7 of 7

3 rows

Characteristic	Value	Unit	Method
UL Recognized (94V-0 Flame Class Rating) ᵖ	min. 0.75	mm	UL 94
Glow Wire Ignitability Temperature (at 0.75 mm) ᵖ	800	°C	IEC 60695-2-13
Glow Wire Flammability Index (at 0.75 mm) ᵖ	960	°C	IEC 60695-2-12