LNP™ LUBRILOY™ Compound RF206

Chemical Family: Polyamides

SABIC's Specialties Business LNP LUBRILOY RF206 compound is based on Nylon 6/6 resin containing 30% glass fiber and proprietary lubricant. Added features of this grade include: Wear Resistant. This product does not contain PFAS intentionally added during SHPP’s manufacturing process and are not expected to contain unintentional PFAS impurities. Each user is responsible for evaluating the presence of unintentional PFAS impurities.

Product families

Plastics — Engineering & Specialty Polymers

Polyamides

Other characteristics

Brand: LNP™ LUBRILOY™ Compound
Polymer Name: Polyamide 66 (PA 66)
Fillers Included: Glass Fiber
Flexural Modulus: 7500.0 - 7500.0 MPa
Additives Included: Heat Stabilizer, Lubricant (Unspecified), Mold Release Agent, Proprietary; Heat Stabilizer; Lubricant (Unspecified); Mold Release Agent; Proprietary
Processing Methods: Injection Molding
Note: ᵍ Measurements made from Laboratory test Coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.; ᵖ UL ratings shown on the technical datasheet might not cover the full range of thicknesses and colors. For details, please see the UL Yellow Card.; ⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.; ¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.
Markets: Building & Construction
Consumer Goods
Electrical & Electronics
Personal Care
Printing & Packaging
Flame Rating: UL 94 HB
Technology: Plastics
Labeling Claims: No Added PFAS
Material Features: Friction Resistant
Good Mold Release
Heat Stabilized
Lubricated
No Added PFAS
Wear Resistant
Compounds Feature: Improved impact over PTFE filled materials
Lower mold deposits
Excellent surface finish & colorability
Lower S.G. vs. PTFE filled materials
Non-halogenated lubrication
Certifications and Compliance: UL 94
Plastics and Elastomers End Uses: Appliances
Building Materials
Cell Phones
Commercial Appliance
Computer Components
Consumer Applications
Containers
Displays

Technical data

Table 1 of 6

13 rows

Characteristic	Value	Unit	Method
Density ¹¹	1.24	g/cm³	ISO 1183
Density ¹¹	1.24	g/cm³	ASTM D792
Moisture Absorption (at 23°C, 50% RH, 24hrs) ¹¹	0.3 - 0.6	%	ASTM D570
Water Absorption (at 23°C, 24hrs) ¹¹	0.3 - 0.6	%	ASTM D570
Water Absorption (at 23°C, 24hrs) ¹¹	0.3 - 0.6	%	ISO 62-1
Melt Flow Rate (at 300°C, 2.16 kgf) ¹¹	30	g/10 min	ASTM D1238
Dynamic COF ¹¹	0.51	—	ASTM D3702 Modified: Manual
Static COF ¹¹	0.5	—	ASTM D3702 Modified: Manual
Wear Factor Washer ¹¹	36	10^-10 in^5-min/ft-lb-hr	ASTM D3702 Modified: Manual
Moisture Absorption (at 23°C, 50% RH) ¹¹	0.3 - 0.6	%	ISO 62
Melt Volume Rate (at 300°C, 2.16 kg) ¹¹	30	cm³/10 min	ISO 1133
Mold Shrinkage (flow) ᵍ ¹¹	0.2 - 0.6	%	SABIC method

Table 2 of 6

10 rows

Characteristic	Value	Unit	Method
Tensile Modulus (at 5 mm/min) ¹¹	9000	MPa	ASTM D638
Tensile Strain (Break, Type I, 5 mm/min) ¹¹	2.5	%	ASTM D638
Tensile Stress (Break, Type I, 5 mm/min) ¹¹	122	MPa	ASTM D638
Flexural Modulus (at 1.3 mm/min, 50 mm span) ¹¹	7200	MPa	ASTM D790
Flexural Strength (at 1.3 mm/min, 50 mm span) ¹¹	190	MPa	ASTM D790
Tensile Modulus (at 1 mm/min) ¹¹	9000	MPa	ISO 527
Tensile Strain (Break, 5 mm/min) ¹¹	3.2	%	ISO 527
Tensile Stress (Break, 5 mm/min) ¹¹	135	MPa	ISO 527
Flexural Modulus (at 2 mm/min) ¹¹	7500	MPa	ISO 178
Flexural Strength (at 2 mm/min) ¹¹	195	MPa	ISO 178

Table 3 of 6

14 rows

Characteristic	Value	Unit	Method
Heat Deflection Temperature (at 0.45 MPa, 3.2 mm, Unannealed) ¹¹	2.58E+02	°C	ASTM D648
Heat Deflection Temperature (at 1.82 MPa, 3.2mm, Unannealed) ¹¹	241	°C	ASTM D648
Vicat Softening Temperature (Rate B/50) ¹¹	185	°C	ISO 306
Vicat Softening Temperature (Rate B/50) ¹¹	185	°C	ASTM D1525
Coefficient of Thermal Expansion (at -40°C to 40°C, flow) ¹¹	0.000037	1/°C	ASTM E831
Coefficient of Thermal Expansion (at -40°C to 40°C, xflow) ¹¹	0.000069	1/°C	ASTM E831
Heat Deflection Temperature/Af (at 1.8 Mpa, Flatw 80104, sp=64mm) ¹¹	228	°C	ISO 75/Af
Heat Deflection Temperature/Bf (at 0.45 Mpa, Flatw 80104, sp=64mm) ¹¹	252	°C	ISO 75/Bf
Vicat Softening Temperature (Rate B/120) ¹¹	185	°C	ISO 306
Coefficient of Thermal Expansion (at 23°C to 60°C, flow) ¹¹	0.000019	1/°C	ISO 11359-2
Coefficient of Thermal Expansion (at 23°C to 60°C, xflow) ¹¹	0.00011	1/°C	ISO 11359-2
Relative Temperature Index (Electrical) ᵖ ¹¹	65	°C	UL 746B

Table 4 of 6

8 rows

Characteristic	Value	Unit	Method
Izod Impact (Notched, at 23°C) ¹¹	95	J/m	ASTM D256
Izod Impact (Unnotched, at 23°C) ¹¹	800	J/m	ASTM D4812
Instrumented Dart Impact Energy (Peak, at 23°C) ¹¹	12	J	ASTM D3763
Instrumented Dart Impact Total Energy (at 23°C) ¹¹	13	J	ASTM D3763
Izod Impact (Notched, 80104, at 23°C) ¹¹	12	kJ/m²	ISO 180/1A
Izod Impact (Unnotched, 80104, at 23°C) ¹¹	58	kJ/m²	ISO 180/1U
Charpy Impact (at 23°C, V-notch Edgew 80104 sp=62mm) ¹¹	17	kJ/m²	ISO 179/1eA
Charpy Impact (at 23°C, Unnotch Edgew 80104 sp=62mm) ¹¹	70	kJ/m²	ISO 179/1eU

Table 5 of 6