To catalogue
ULTEM™ Resin ATX200
- Chemical Family
- Polyetherimide (PEI)Polyimides (PI)
High flow Polyetherimide blend. ECO Conforming, UL94 V0 Listing.
Other characteristics
- Brand
- ULTEM™ Resin
- Polymer Name
- Polyether Imide (PEI)
- Additives Included
Flame Retardant, Heat Stabilizer, Plasticizer (Polycarboxylate)
- Processing Methods
- Injection Molding
- Note
ᵖ UL ratings shown on the technical datasheet might not cover the full range of thicknesses and colors. For details, please see the UL Yellow Card.. ʳ UL Ratings shown on the technical datasheet might not cover the full range of thicknesses, colors and regions. For details, please see the UL Yellow Card.
- Markets
- Automotive & Transportation
- Consumer Goods
- Electrical & Electronics
- Healthcare & Pharma
- Industrial
- Printing & Packaging
- Availability
ULTEM™ resin is available in transparent and opaque custom colors, and can be glass filled for added stiffness.
- Flame Rating
- UL 94 V0
- UL 94 V2
- Key Benefits
- Heat Resistance
- Dimensional Stability
- Dielectric Performance
- Miniaturization and Thin Wall
- Resilience
- Technology
- Plastics
- Labeling Claims
- Bio-based
- Confirms to ECO-Label
- Low Toxicity
- Sustainable
Technical data
Table 1 of 7
18 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Tensile Stress (Yield, Type I, 5 mm/min) | 96 | MPa | ASTM D638 |
| Tensile Strain (Break, Type I, 5 mm/min) | 70 | % | ASTM D638 |
| Tensile Stress (Break, Type I, 5 mm/min) | 85 | MPa | ASTM D638 |
| Flexural Stress (Yield, 2.6 mm/min, 100 mm span) | 144 | MPa | ASTM D790 |
| Tensile Strain (Yield, Type I, 5 mm/min) | 7 | % | ASTM D638 |
| Flexural Modulus (at 2.6 mm/min, 100 mm span) | 3170 | MPa | ASTM D790 |
| Tensile Modulus (at 5 mm/min) | 3300 | MPa | ASTM D638 |
| Flexural Stress (Yield, 1.3 mm/min, 50 mm span) | 145 | MPa | ASTM D790 |
| Flexural Modulus (at 1.3 mm/min, 50 mm span) | 3170 | MPa | ASTM D790 |
| Taber Abrasion (CS-17, 1 kg) | 20 | mg/1000cy | SABIC method |
| Tensile Stress (Yield, 50 mm/min) | 95 | MPa | ISO 527 |
| Tensile Stress (Break, 50 mm/min) | 75 | MPa | ISO 527 |
Table 2 of 7
9 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Specific Gravity | 1.26 | — | ASTM D792 |
| Mold Shrinkage (flow, 3.2 mm) | 0.5 - 0.7 | % | SABIC method |
| Melt Flow Rate (at 337°C, 6.6 kgf) | 24 | g/10 min | ASTM D1238 |
| Mold Shrinkage (on Tensile Bar, flow) | 0.5 - 0.7 | % | SABIC method |
| Mold Shrinkage (xflow, 3.2 mm) | 0.5 - 0.7 | % | SABIC method |
| Density | 1.26 | g/cm³ | ISO 1183 |
| Water Absorption (at 23°C, saturated) | 0.9 | % | ISO 62-1 |
| Moisture Absorption (at 23°C, 50% RH) | 0.5 | % | ISO 62 |
| Melt Volume Rate (at 340°C, 5.0 kg) | 16 | cm³/10 min | ISO 1133 |
Table 3 of 7
17 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Heat Deflection Temperature (at 1.82 MPa, 6.4 mm, Unannealed) | 190 | °C | ASTM D648 |
| Relative Temperature Index (Electrical) ᵖ | 115 | °C | UL 746B |
| Relative Temperature Index (Mechanical with impact) ᵖ | 115 | °C | UL 746B |
| Relative Temperature Index (Mechanical without impact) ᵖ | 115 | °C | UL 746B |
| Vicat Softening Temperature (Rate B/50) | 200 | °C | ISO 306 |
| Vicat Softening Temperature (Rate B/50) | 209 | °C | ASTM D1525 |
| Heat Deflection Temperature (at 1.82 MPa, 3.2mm, Unannealed) | 187 | °C | ASTM D648 |
| Coefficient of Thermal Expansion (at -40°C to 150°C, flow) | 0.00005 | 1/°C | ASTM E831 |
| Coefficient of Thermal Expansion (at -40°C to 150°C, xflow) | 0.00005 | 1/°C | ASTM E831 |
| Thermal Conductivity | 0.23 | W/m-°C | ISO 8302 |
| Coefficient of Thermal Expansion (at 23°C to 150°C, flow) | 0.00005 | 1/°C | ISO 11359-2 |
| Coefficient of Thermal Expansion (at 23°C to 150°C, xflow) | 0.00005 | 1/°C | ISO 11359-2 |
Table 4 of 7
10 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Comparative Tracking Index (UL, PLC) | 4 | PLC Code | UL 746A |
| Hot Wire Ignition (PLC 0) | min. 0.75 | mm | UL 746A |
| High Ampere Arc Ignition (PLC 4) | min. 0.75 | mm | UL 746A |
| Volume Resistivity | 1.00E+15 | Ω.cm | IEC 60093 |
| Surface Resistivity (ROA) | min. 1.E+15 | Ω | IEC 60093 |
| Relative Permittivity (1 MHz) | 2.9 | — | IEC 60250 |
| Dissipation Factor (at 50/60 Hz) | 0.001 | — | IEC 60250 |
| Dissipation Factor (at at 1 MHz) | 0.005 | — | IEC 60250 |
| Comparative Tracking Index ʳ | 150 | V | IEC 60112 |
| Relative Permittivity (50/60 Hz) | 2.9 | — | IEC 60250 |
Table 5 of 7
9 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Izod Impact (Unnotched, at 23°C) | 2082 | J/m | ASTM D4812 |
| Izod Impact (Notched, at 23°C) | 53 | J/m | ASTM D256 |
| Izod Impact (Reverse Notched, 3.2 mm) | 2136 | J/m | ASTM D256 |
| Izod Impact (Notched, at -30°C) | 55 | J/m | ASTM D256 |
| Instrumented Dart Impact Total Energy (at 23°C) | 50 | J | ASTM D3763 |
| Izod Impact (Notched, 80*10*4, at 23°C) | 5 | kJ/m² | ISO 180/1A |
| Izod Impact (Notched, 80*10*4, at -30°C) | 5 | kJ/m² | ISO 180/1A |
| Charpy Impact (at 23°C, V-notch Edgew 80*10*4 sp=62mm) | 4 | kJ/m² | ISO 179/1eA |
| Charpy Impact (at -30°C, V-notch Edgew 80*10*4 sp=62mm) | 4 | kJ/m² | ISO 179/1eA |
Table 6 of 7
23 rows| Characteristic | Value | Unit |
|---|---|---|
| Back Pressure | 0.3 - 0.7 | MPa |
| Drying Temperature | 135 | °C |
| Drying Temperature | 130 - 140 | °C |
| Drying Time | 3 - 4 | Hrs |
| Drying Time | 4 - 6 | Hrs |
| Drying Time (Cumulative) | 10 | Hrs |
| Front - Zone 3 Temperature | 340 - 360 | °C |
| Front - Zone 3 Temperature | 350 - 370 | °C |
| Maximum Moisture Content | 0.02 | % |
| Melt Temperature | 350 - 370 | °C |
| Melt Temperature | 340 - 380 | °C |
| Middle - Zone 2 Temperature | 345 - 365 | °C |
Table 7 of 7
2 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| UL Recognized (94V-0 Flame Class Rating) ᵖ | min. 1.5 | mm | UL 94 |
| UL Recognized (94V-2 Flame Class Rating) ᵖ | min. 0.75 | mm | UL 94 |
