To catalogue
LNP™ COLORCOMP™ Compound D10008P
- Chemical Family
- Polycarbonate (PC)
LNP COLORCOMP D10008P compound is based on Polycarbonate (PC) resin. Added features of this grade include: Flame Retardant, Exceptional Processing.
Product families
Applications
Applications
- Consumer Goods — Appliances & Electronics
- Consumer Goods — Housewares
- Consumer Goods — Sports & Recreation
Automotive & Transportation — Automotive
- Interior
Electrical & Electronics — Devices & Assemblies
- Consumer Electronics
- Displays
Printing & Packaging — Packaging
- Non-Food Consumer Packaging
Personal Care — Packaging & Accessories
- Applicators & Accessories
Electrical & Electronics — Parts & Components
- Housings & Enclosures
Product Families
Plastics — Engineering & Specialty Polymers
- High Performance Thermoplastics
- Polycarbonates
Other characteristics
- Brand
- LNP™ COLORCOMP™ Compound
- Polymer Name
- Polycarbonate (PC)
- Flexural Modulus
- 2300.0 - 2300.0 MPa
- Additives Included
- Flame Retardant
- Processing Methods
- Injection Molding
- Note
ᵍ Measurements made from Laboratory test Coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.; ᵖ UL ratings shown on the technical datasheet might not cover the full range of thicknesses and colors. For details, please see the UL Yellow Card.; ⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.; ¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.
- Color
- Custom
- Markets
- Automotive & Transportation
- Consumer Goods
- Electrical & Electronics
- Personal Care
- Printing & Packaging
- Flame Rating
- UL 94 V2
- Technology
- Plastics
- Material Features
- Dimensional Stability
- Excellent Aesthetics
- Flame Retardant
- Good Aesthetics
- Good Processability
- Good Surface Appearance
- High Flowability
- Non-brominated
- Certifications and Compliance
- UL 94
- Plastics and Elastomers End Uses
- Appliances
- Automotive Applications
- Automotive Interior Parts
- Cell Phones
- Commercial Appliance
- Computer Components
- Consumer Applications
- Containers
- Plastics and Elastomers Functions
- Resin
- Plastics and Elastomers Processing Methods
- Injection Molding
Technical data
Table 1 of 8
17 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Tensile Stress (Yield, 50 mm/min) ¹¹ | 63 | MPa | ISO 527 |
| Tensile Stress (Break, 50 mm/min) ¹¹ | 50 | MPa | ISO 527 |
| Tensile Strain (Yield, 50 mm/min) ¹¹ | 6 | % | ISO 527 |
| Tensile Strain (Break, 50 mm/min) ¹¹ | 70 | % | ISO 527 |
| Tensile Modulus (at 1 mm/min) ¹¹ | 2350 | MPa | ISO 527 |
| Flexural Stress (Yield, at 2 mm/min) ¹¹ | 90 | MPa | ISO 178 |
| Flexural Modulus (at 2 mm/min) ¹¹ | 2300 | MPa | ISO 178 |
| Tensile Stress (Yield, Type I, 50 mm/min) ¹¹ | 62 | MPa | ASTM D638 |
| Tensile Stress (Break, Type I, 50 mm/min) ¹¹ | 65 | MPa | ASTM D638 |
| Tensile Strain (Yield, Type I, 50 mm/min) ¹¹ | 6 | % | ASTM D638 |
| Tensile Strain (Break, Type I, 50 mm/min) ¹¹ | 120 | % | ASTM D638 |
| Tensile Modulus (at 50 mm/min) ¹¹ | 2370 | MPa | ASTM D638 |
Table 2 of 8
9 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Melt Volume Rate (at 300°C, 1.2 kg) ¹¹ | 23 | cm³/10 min | ISO 1133 |
| Specific Gravity ¹¹ | 1.2 | — | ASTM D792 |
| Specific Volume ¹¹ | 0.83 | cm³/g | ASTM D792 |
| Density ¹¹ | 1.19 | g/cm³ | ASTM D792 |
| Water Absorption (at 23°C, 24hrs) ¹¹ | 0.15 | % | ASTM D570 |
| Water Absorption (at 23°C, saturated) ¹¹ | 0.35 | % | ASTM D570 |
| Water Absorption (Equilibrium, at 100°C) ¹¹ | 0.58 | % | ASTM D570 |
| Melt Flow Rate (at 300°C, 1.2 kgf) ¹¹ | 25 | g/10 min | ASTM D1238 |
| Mold Shrinkage (flow, 3.2 mm) ᵍ ¹¹ | 0.5 - 0.7 | % | SABIC method |
Table 3 of 8
17 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Heat Deflection Temperature/Be (at 0.45MPa, Edgew 120*10*4, sp=100mm) ¹¹ | 133 | °C | ISO 75/Be |
| Heat Deflection Temperature/Ae (at 1.8 Mpa, Edgew 120*10*4, sp=100mm) ¹¹ | 121 | °C | ISO 75/Ae |
| Vicat Softening Temperature (Rate A/50) ¹¹ | 145 | °C | ISO 306 |
| Vicat Softening Temperature (Rate B/50) ¹¹ | 139 | °C | ISO 306 |
| Vicat Softening Temperature (Rate B/120) ¹¹ | 140 | °C | ISO 306 |
| Thermal Conductivity ¹¹ | 0.2 | W/m-°C | ISO 8302 |
| Thermal Conductivity ¹¹ | 0.19 | W/m-°C | ASTM C177 |
| Coefficient of Thermal Expansion (at 23°C to 80°C, flow) ¹¹ | 0.00007 | 1/°C | ISO 11359-2 |
| Ball Pressure Test (at 123°C to 127°C) ¹¹ | Pass | — | IEC 60695-10-2 |
| Heat Deflection Temperature (at 1.82 MPa, 3.2mm, Unannealed) ¹¹ | 126 | °C | ASTM D648 |
| Heat Deflection Temperature (at 0.45 MPa, 6.4 mm, Unannealed) ¹¹ | 137 | °C | ASTM D648 |
| Heat Deflection Temperature (at 1.82 MPa, 6.4 mm, Unannealed) ¹¹ | 126 | °C | ASTM D648 |
Table 4 of 8
22 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Volume Resistivity ¹¹ | min. 1.E+15 | Ω.cm | IEC 60093 |
| Volume Resistivity ¹¹ | 1.00E+17 | Ω.cm | ASTM D257 |
| Dielectric Strength (in air, at 3.2mm) ¹¹ | 14.9 | kV/mm | ASTM D149 |
| Relative Permittivity (50/60 Hz) ¹¹ | 2.7 | — | IEC 60250 |
| Relative Permittivity (50/60 Hz) ¹¹ | 3.17 | — | ASTM D150 |
| Relative Permittivity (1 MHz) ¹¹ | 2.7 | — | IEC 60250 |
| Relative Permittivity (1 MHz) ¹¹ | 2.96 | — | ASTM D150 |
| Dissipation Factor (at 50/60 Hz) ¹¹ | 0.001 | — | IEC 60250 |
| Dissipation Factor (at 50/60 Hz) ¹¹ | 0.0009 | — | ASTM D150 |
| Dissipation Factor (at at 1 MHz) ¹¹ | 0.01 | — | IEC 60250 |
| Dissipation Factor (at at 1 MHz) ¹¹ | 0.01 | — | ASTM D150 |
| High Voltage Arc Track Rate (PLC) ¹¹ | 2 | PLC Code | UL 746A |
Table 5 of 8
3 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Light Transmission (at 2.54 mm) ¹¹ | 88 | % | ASTM D1003 |
| Haze (at 2.54 mm) ¹¹ | 1 | % | ASTM D1003 |
| Refractive Index ¹¹ | 1.586 | — | ASTM D542 |
Table 6 of 8
10 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Charpy Impact (at 23°C, V-notch Edgew 80*10*4 sp=62mm) ¹¹ | 12 | kJ/m² | ISO 179/1eA |
| Charpy Impact (at -30°C, V-notch Edgew 80*10*4 sp=62mm) ¹¹ | 10 | kJ/m² | ISO 179/1eA |
| Izod Impact (Notched, 80*10*4, at 23°C) ¹¹ | 12 | kJ/m² | ISO 180/1A |
| Izod Impact (Notched, 80*10*4, at -30°C) ¹¹ | 10 | kJ/m² | ISO 180/1A |
| Izod Impact (Notched, at 23°C) ¹¹ | 640 | J/m | ASTM D256 |
| Izod Impact (Notched, natural, tints) ¹¹ | 640 | J/m | ASTM D256 |
| Tensile Impact Strength (Type S) ¹¹ | 378 | kJ/m² | ASTM D1822 |
| Falling Dart Impact (at 23°C) ¹¹ | 169 | J | ASTM D3029 |
| Instrumented Dart Impact Energy (Peak, at 23°C) ¹¹ | 54 | J | ASTM D3763 |
| Izod Impact (Unnotched, at 23°C) ¹¹ | 3204 | J/m | ASTM D4812 |
Table 7 of 8
14 rows| Characteristic | Value | Unit |
|---|---|---|
| Drying Temperature ⁷ | 120 | °C |
| Drying Time ⁷ | 3 - 4 | Hrs |
| Drying Time (Cumulative) ⁷ | 48 | Hrs |
| Maximum Moisture Content ⁷ | 0.02 | % |
| Melt Temperature ⁷ | 270 - 295 | °C |
| Nozzle Temperature ⁷ | 265 - 290 | °C |
| Front - Zone 3 Temperature ⁷ | 270 - 295 | °C |
| Middle - Zone 2 Temperature ⁷ | 260 - 280 | °C |
| Rear - Zone 1 Temperature ⁷ | 250 - 270 | °C |
| Mold Temperature ⁷ | 70 - 95 | °C |
| Back Pressure ⁷ | 0.3 - 0.7 | MPa |
| Screw Speed ⁷ | 40 - 70 | rpm |
Table 8 of 8
2 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| UL Recognized (94V-2 Flame Class Rating) ᵖ | min. 1.1 | mm | UL 94 |
| Oxygen Index (LOI) ᵖ | 25 | % | ISO 4589 |
