LNP™ VERTON™ Compound MV006S
- Chemical Family
- PolyolefinsPolypropylenes (PP)
LNP™ VERTON™ Compound MV006S is a polypropylene (PP) resin-based compound enriched with 30% long glass fiber. Engineered to be chemically coupled, structurally robust, and heat stabilized, this material offers exceptional stiffness and strength. It is specifically designed for demanding applications in automotive exteriors, water management, sports and leisure, as well as home and commercial appliances. Its advanced formulation ensures durability and performance, making it an optimal choice for injection molding processes where strength, stability, and resistance to environmental factors are essential requirements.
Product families
Applications
- Consumer Goods — Appliances & Electronics
- Consumer Goods — Sports & Recreation
- Exterior & Body
- Waterproofing & Weatherproofing
- Equipment & Parts
- Consumer Electronics
Product Families
- Polyolefins
Other characteristics
- Brand
- LNP™ VERTON™ Compound
- Polymer Name
- Polypropylene (unspecified)
- Fillers Included
- Glass Fiber, Long Glass Fiber
- Glass Fiber
- Long Glass Fiber
- Processing Methods
- Injection Molding
- Note
¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design. ² UL Ratings shown on the technical datasheet might not cover the full range of thicknesses and colors. For details, please see the UL Yellow Card. ³ Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article. ⁴ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.
- Markets
- Automotive & Transportation
- Building & Construction
- Consumer Goods
- Electrical & Electronics
- Industrial
- Technology
- Plastics
- Labeling Claims
- No Added PFAS
- Material Features
- Chemically Coupled
- Heat Stabilized
- High Stiffness
- High Strength
- Certifications and Compliance
- UL 94
- Plastics and Elastomers End Uses
- Automotive Applications
- Commercial Appliance
- Construction Applications
- Home Appliances
- Water Management
- Plastics and Elastomers Functions
- Resin
- Plastics and Elastomers Processing Methods
- Injection Molding
Technical data
Table 1 of 6
12 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Tensile Stress (Break) ¹ | 110.0 | MPa | ISO 527 |
| Tensile Strain (Break) ¹ | 2.2 | % | ISO 527 |
| Tensile Modulus (at 1 mm/min) ¹ | 7500.0 | MPa | ISO 527 |
| Flexural Modulus ¹ | 6000.0 | MPa | ISO 178 |
| Flexural Stress (Yield, 2 mm/min) ¹ | 135.0 | MPa | ISO 178 |
| Flexural Stress (Break, 2 mm/min) ¹ | 130.0 | MPa | ISO 178 |
| Tensile Modulus (at 5 mm/min) ¹ | 7100.0 | MPa | ASTM D638 |
| Tensile Strain (Break, Type I, 5 mm/min) ¹ | 2.8 | % | ASTM D638 |
| Tensile Stress (Break, Type I, 5 mm/min) ¹ | 95.0 | MPa | ASTM D638 |
| Flexural Modulus (at 1.3 mm/min, 50 mm span) ¹ | 6100.0 | MPa | ASTM D790 |
| Flexural Stress (Yield, 1.3 mm/min, 50 mm span) ¹ | 135.0 | MPa | ASTM D790 |
| Flexural Stress (Break, 1.3 mm/min, 50 mm span) ¹ | 130.0 | MPa | ASTM D790 |
Table 2 of 6
12 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Density ¹ | 1.12 | g/cm³ | ISO 1183 |
| Density ¹ | 1.12 | g/cm³ | ASTM D792 |
| Moisture Absorption (23°C / 50% RH) ¹ | 0.008 | % | ISO 62 |
| Water Absorption (23°C/saturated) ¹ | 0.07 | % | ISO 62-1 |
| Mold Shrinkage (flow, 24 hrs) ¹ | 0.21 | % | ISO 294 |
| Mold Shrinkage (xflow, 24 hrs) ¹ | 0.28 | % | ISO 294 |
| Water Absorption (23°C/24hrs) ¹ | 0.03 | % | ASTM D570 |
| Mold Shrinkage (flow, 24 hrs) ³ | 0.21 | % | ASTM D955 |
| Mold Shrinkage (xflow, 24 hrs) ³ | 0.28 | % | ASTM D955 |
| Wear Factor Washer ³ | 44.0 | 10^-10 in^5-min/ft-lb-hr | ASTM D3702 Modified: Manual |
| Dynamic Coefficient of Friction ³ | 0.36 | — | ASTM D3702 Modified: Manual |
| Static COF ³ | 0.39 | — | ASTM D3702 Modified: Manual |
Table 3 of 6
12 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Vicat Softening Temperature (at Rate B/50) ¹ | 140.0 | °C | ISO 306 |
| Vicat Softening Temperature (at Rate B/50) ¹ | 140.0 | °C | ASTM D1525 |
| Heat Deflection Temperature/Af (1.8 MPa Flatw 80*10*4 sp=64mm) ¹ | 157.0 | °C | ISO 75/Af |
| Heat Deflection Temperature/Bf (0.45 MPa Flatw 80*10*4 sp=64mm) ¹ | 164.0 | °C | ISO 75/Bf |
| Coefficient of Thermal Expansion (at -40°C to 40°C, flow) ¹ | 2.5e-05 | 1/°C | ISO 11359-2 |
| Coefficient of Thermal Expansion (at -40°C to 40°C, flow) ¹ | 3.9e-05 | 1/°C | ASTM E831 |
| Coefficient of Thermal Expansion (at -40°C to 40°C, xflow) ¹ | 8.0e-05 | 1/°C | ISO 11359-2 |
| Coefficient of Thermal Expansion (at -40°C to 40°C, xflow) ¹ | 7.1e-05 | 1/°C | ASTM E831 |
| Heat Deflection Temperature (1.82 MPa, 3.2mm, unannealed) ¹ | 156.0 | °C | ASTM D648 |
| Relative Temperature Index (Elec) ² | 65.0 | °C | UL 746B |
| Relative Temperature Index (Mech with impact) ² | 65.0 | °C | UL 746B |
| Relative Temperature Index (Mech w/o impact) ² | 65.0 | °C | UL 746B |
Table 4 of 6
8 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Izod Impact (Notched 80*10*4 +23°C) ¹ | 24.0 | kJ/m² | ISO 180/1A |
| Izod Impact (Unnotched 80*10*4 +23°C) ¹ | 42.0 | kJ/m² | ISO 180/1U |
| Charpy Impact (at 23°C, V-notch Edgew 80*10*4 sp=62mm) ¹ | 24.0 | kJ/m² | ISO 179/1eA |
| Charpy Impact (at 23°C, Unnotch Edgew 80*10*4 sp=62mm) ¹ | 35.0 | kJ/m² | ISO 179/1eU |
| Izod Impact (Notched, 23°C) ¹ | 195.0 | J/m | ASTM D256 |
| Izod Impact (Unnotched, 23°C) ¹ | 460.0 | J/m | ASTM D4812 |
| Multiaxial Impact ¹ | 14.0 | J | ISO 6603 |
| Instrumented Dart Impact Energy (at peak, 23°C) ¹ | 8.0 | J | ASTM D3763 |
Table 5 of 6
9 rows| Characteristic | Value | Unit |
|---|---|---|
| Drying Temperature ⁴ | 80.0 | °C |
| Drying Time ⁴ | 4.0 | Hrs |
| Melt Temperature ⁴ | 220 - 250 | °C |
| Front - Zone 3 Temperature ⁴ | 250 - 260 | °C |
| Middle - Zone 2 Temperature ⁴ | 245 - 255 | °C |
| Rear - Zone 1 Temperature ⁴ | 230 - 245 | °C |
| Mold Temperature ⁴ | 40 - 65 | °C |
| Back Pressure ⁴ | 0.2 - 0.3 | MPa |
| Screw Speed ⁴ | 30 - 60 | rpm |
Table 6 of 6
1 row| Characteristic | Value | Unit | Method |
|---|---|---|---|
| UL Recognized 94HB Flame Class Rating ² | min. 1.5 | mm | UL 94 |
