NORYL™ Resin NHP5054
NORYL NHP5054 Resin is a glass fiber-reinforced PPE and PS blend well-suited for evaluation in electric vehicle battery housings, automotive enclosures, electrical components, and components that need thin-wall flame resistance, modulus retention, and high heat resistance. NORYL NHP5054 Resin is an injection-moldable material that contains non-brominated, non-chlorinated flame retardant.NORYL NHP5054 Resin features include:A UL94 flame rating of V0 at 0.75mmGood dimensional stabilityHigh heat resistanceStrong electrical performanceLow specific gravityThe resin is well-suited for evaluation in electric vehicle battery housings, automotive enclosures, electrical components, and components that need thin-wall flame resistance, modulus retention, and high heat resistance.This product does not contain PFAS intentionally added during SHPP’s manufacturing process. Each user is responsible for evaluating the presence of unintentional PFAS impurities.
Product families
Applications
- Consumer Goods — Appliances & Electronics
- Automotive Electronics
- Consumer Electronics
- Displays
- Batteries
- Connectors
- Housings & Enclosures
- Switches & Relays
Product Families
- Blends & Alloys
Other characteristics
- Brand
- NORYL™ Resin
- Density
- 1300.0 - 1300.0 kg/m³
- Polymer Name
- PPO/PS Alloy
- Processing Methods
- Injection Molding
- Note
ᵍ Measurements made from Laboratory test Coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.; ᵖ UL ratings shown on the technical datasheet might not cover the full range of thicknesses and colors. For details, please see the UL Yellow Card.; ⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.; ¹³ This rating is not intended to reflect hazards presented by this or any other material under actual fire conditions. UL Ratings shown on the technical datasheet might not cover the full range of thicknesses, colors and regions. For details, please see the UL Yellow Card.; ¹⁵ Typical values only. Variations within normal tolerances are possible for various colors. All values are measured at least after 48 hours storage at 23°C/50% relative humidity. All properties, except the melt volume rate are measured on injection molded samples. All samples are prepared according to ISO 294. Only typical data for material selection purpose.Not to be used for part or tool design. The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.
- Markets
- Consumer Goods
- Electrical & Electronics
- Flame Rating
- UL 94 V0
- Technology
- Plastics
- Labeling Claims
- Bromine-free
- Chlorine-free
- No Added PFAS
- Fillers Included
- Glass Fiber
- Additives Included
- Flame Retardant
- Heat Stabilizer
- Material Features
- Amorphous
- Dimensional Stability
- Flame Retardant
- Good Processability
- Good Stiffness
- Heat Stabilized
- High Hydrolytic Stability
- High Stiffness
- Attributes
NORYL NHP5054 resin is a 20% glass reinforced blend of polyphenylene ether (PPE) and high impact polystyrene (HIPS). This injection moldable grade contains non-brominated, non-chlorinated flame retardant and carries a UL94 flame rating of VO at 0.75 mm for thin-wall molding capability. NORYL NHP5054 resin is based on a unique copolymer technology and exhibits good dimensional stability, high heat resistance, strong electrical performance, and very low specific gravity. Itis an excellent candidate for electric vehicle module and battery housings, automotive under-the-hood enclosures and components where thin-wall FR, modulus retention, and high heat resistance is required.
- Country Availability
- Canada
- China (Mainland)
- Mexico
- USA
- Certifications and Compliance
- UL 94
- Plastics and Elastomers End Uses
- AC Charging Cabinet
- Automotive Under The Hood
- Batteries
- Cell Phones
- Computer Components
- Connectors
- Displays
- EV Charging Connectors
- Plastics and Elastomers Functions
- Resin
- Plastics and Elastomers Processing Methods
- Injection Molding
Technical data
Table 1 of 6
8 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Specific Gravity ¹⁵ | 1.3 | — | ASTM D792 |
| Melt Flow Rate (at 250°C, 10.0 kgf) ¹⁵ | 8 | g/10 min | ASTM D1238 |
| Melt Volume Rate (at 280°C, 10.0 kg) ¹⁵ | 22 | cm³/10 min | ISO 1133 |
| Mold Shrinkage (on Tensile Bar, flow) ᵍ ¹⁵ | 0.27 | % | SABIC method |
| Density ¹⁵ | 1.27 | g/cm³ | ISO 1183 |
| Moisture Absorption (at 23°C, 50% RH) ¹⁵ | 0.24 | % | ISO 62 |
| Mold Shrinkage (flow) ᵍ ¹⁵ | 0.22 | % | SABIC method |
| Mold Shrinkage (xflow) ᵍ ¹⁵ | 0.52 | % | SABIC method |
Table 2 of 6
10 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Tensile Strain (Break, Type I, 5 mm/min) ¹⁵ | 2.5 | % | ASTM D638 |
| Tensile Stress (Yield, Type I, 5 mm/min) ¹⁵ | 120 | MPa | ASTM D638 |
| Flexural Modulus (at 2.6 mm/min, 100 mm span) ¹⁵ | 6000 | MPa | ASTM D790 |
| Flexural Stress (Yield, 2.6 mm/min, 100 mm span) ¹⁵ | 150 | MPa | ASTM D790 |
| Tensile Strain (Break, 5 mm/min) ¹⁵ | 2.4 | % | ISO 527 |
| Tensile Stress (Break, 5 mm/min) ¹⁵ | 110 | MPa | ISO 527 |
| Flexural Modulus (at 2 mm/min) ¹⁵ | 6000 | MPa | ISO 178 |
| Flexural Stress (Yield, at 2 mm/min) ¹⁵ | 145 | MPa | ISO 178 |
| Tensile Modulus (at 1 mm/min) ¹⁵ | 7300 | MPa | ISO 527 |
| Ball Indentation Hardness (H358/30) ¹⁵ | 215 | MPa | ISO 2039-1 |
Table 3 of 6
12 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Heat Deflection Temperature (at 1.82 MPa, 6.4 mm, Unannealed) ¹⁵ | 120 | °C | ASTM D648 |
| Heat Deflection Temperature/Af (at 1.8 Mpa, Flatw 80*10*4, sp=64mm) ¹⁵ | 115 | °C | ISO 75/Af |
| Heat Deflection Temperature/Bf (at 0.45 Mpa, Flatw 80*10*4, sp=64mm) ¹⁵ | 122 | °C | ISO 75/Bf |
| Relative Temperature Index (Electrical) ᵖ ¹⁵ | 125 | °C | UL 746B |
| Vicat Softening Temperature (Rate B/120) ¹⁵ | 130 | °C | ISO 306 |
| Vicat Softening Temperature (Rate B/50) ¹⁵ | 128 | °C | ISO 306 |
| Coefficient of Thermal Expansion (at -40°C to 40°C, flow) ¹⁵ | 0.000021 | 1/°C | ISO 11359-2 |
| Coefficient of Thermal Expansion (at -40°C to 40°C, xflow) ¹⁵ | 0.000057 | 1/°C | ISO 11359-2 |
| Coefficient of Thermal Expansion (at 23°C to 80°C, flow) ¹⁵ | 0.000032 | 1/°C | ISO 11359-2 |
| Coefficient of Thermal Expansion (at 23°C to 80°C, xflow) ¹⁵ | 0.000103 | 1/°C | ISO 11359-2 |
| Relative Temperature Index (Mechanical with impact) ᵖ ¹⁵ | 115 | °C | UL 746B |
| Relative Temperature Index (Mechanical without impact) ᵖ ¹⁵ | 125 | °C | UL 746B |
Table 4 of 6
5 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Izod Impact (Notched, at 23°C) ¹⁵ | 100 | J/m | ASTM D256 |
| Charpy Impact (at -30°C, Unnotch Edgew 80*10*4 sp=62mm) ¹⁵ | 36 | kJ/m² | ISO 179/1eU |
| Charpy Impact (at -30°C, V-notch Edgew 80*10*4 sp=62mm) ¹⁵ | 8 | kJ/m² | ISO 179/1eA |
| Charpy Impact (at 23°C, Unnotch Edgew 80*10*4 sp=62mm) ¹⁵ | 35 | kJ/m² | ISO 179/1eU |
| Charpy Impact (at 23°C, V-notch Edgew 80*10*4 sp=62mm) ¹⁵ | 9 | kJ/m² | ISO 179/1eA |
Table 5 of 6
13 rows| Characteristic | Value | Unit |
|---|---|---|
| Drying Temperature ⁷ | 105 - 110 | °C |
| Drying Time ⁷ | 3 - 4 | Hrs |
| Drying Time (Cumulative) ⁷ | 8 | Hrs |
| Maximum Moisture Content ⁷ | 0.02 | % |
| Melt Temperature ⁷ | 280 - 310 | °C |
| Nozzle Temperature ⁷ | 280 - 310 | °C |
| Front - Zone 3 Temperature ⁷ | 270 - 310 | °C |
| Middle - Zone 2 Temperature ⁷ | 260 - 305 | °C |
| Rear - Zone 1 Temperature ⁷ | 250 - 300 | °C |
| Mold Temperature ⁷ | 75 - 105 | °C |
| Back Pressure ⁷ | 0.3 - 0.7 | MPa |
| Screw Speed ⁷ | 20 - 100 | rpm |
Table 6 of 6
4 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| UL Recognized (94V-0 Flame Class Rating) ¹³ | min. 0.75 | mm | UL 94 |
| Glow Wire Flammability Index (at 3 mm) ¹³ | 960 | °C | IEC 60695-2-12 |
| Glow Wire Ignitability Temperature (at 1.0 mm) ¹³ | 775 | °C | IEC 60695-2-13 |
| Glow Wire Ignitability Temperature (at 2.0 mm) ¹³ | 800 | °C | IEC 60695-2-13 |
