To catalogue
NORYL GTX™ Resin GTX202
SABIC's Specialties Business NORYL™ GTX202 resin is a non-reinforced alloy of Polyphenylene Ether (PPE) + Polyamide (PA). This injection moldable grade exhibits excellent chemical resistance and excellent paintability.
Product families
Applications
Applications
- Consumer Goods — Sports & Recreation
Automotive & Transportation — Automotive
- Aftermarket Parts & Components
- Electrical & Electronic Systems
- Exterior & Body
- Interior
Electrical & Electronics — Parts & Components
- Batteries
- Housings & Enclosures
Automotive & Transportation — Transportation
- Off Road & Recreational Vehicle (RV)
- Rail & Mass Transit
Product Families
Plastics — Engineering & Specialty Polymers
- Blends & Alloys
Other characteristics
- Brand
- NORYL GTX™ Resin
- Density
- 1090.0 - 1090.0 kg/m³
- Polymer Name
- PPO/Nylon Alloy
- Flexural Modulus
- 2227.0 - 2227.0 MPa
- Processing Methods
- Injection Molding
- Note
ᵍ Measurements made from Laboratory test Coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.; ⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.; ¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.
- Markets
- Automotive & Transportation
- Consumer Goods
- Electrical & Electronics
- Technology
- Plastics
- Material Features
- Chemical Resistant
- Dimensional Stability
- High Hydrolytic Stability
- High Impact Resistance
- High Stiffness
- High Temperature Resistance
- High Tensile Strength
- Low Moisture Absorption
- Country Availability
- Canada
- China (Mainland)
- Mexico
- USA
- Plastics and Elastomers End Uses
- Automotive Applications
- Automotive Exterior Parts
- Back Panel
- Battery Cover
- Consumer Applications
- Corner Support Plates
- Crash Protection
- Front Panel
- Plastics and Elastomers Functions
- Resin
- Plastics and Elastomers Processing Methods
- Injection Molding
Technical data
Table 1 of 5
19 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Mold Shrinkage (flow, 24 hrs) ᵍ ¹¹ | 1.03 | % | ASTM D955 |
| Mold Shrinkage (flow, 24 hrs) ᵍ ¹¹ | 1.03 | % | ISO 294 |
| Specific Gravity ¹¹ | 1.08 | — | ASTM D792 |
| Density ¹¹ | 1.1 | g/cm³ | ISO 1183 |
| Density ¹¹ | 1.09 | g/cm³ | ISO 1183 |
| Water Absorption (at 23°C, 24hrs) ¹¹ | 0.4 | % | ASTM D570 |
| Water Absorption (at 23°C, saturated) ¹¹ | 3.5 | % | ISO 62-1 |
| Water Absorption (at 23°C, saturated) ¹¹ | 3.6 | % | ASTM D570 |
| Water Absorption (at 23°C, saturated) ¹¹ | 2.02 | % | ISO 62-1 |
| Mold Shrinkage (flow, 3.2 mm) ᵍ ¹¹ | 0.9 - 1.2 | % | SABIC method |
| Moisture Absorption (at 23°C, 50% RH, 24hrs) ¹¹ | 0.2 | % | ASTM D570 |
| Mold Shrinkage (flow, annealed, at 130°C, 1hr) ᵍ ¹¹ | 1.1 - 1.5 | % | ASTM D955 |
Table 2 of 5
25 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Taber Abrasion (CS-17, 1 kg) ¹¹ | 19 | mg/1000cy | ASTM D1044 |
| Taber Abrasion (CS-17, 1 kg) ¹¹ | 15 | mg/1000cy | SABIC method |
| Tensile Stress (Break, 5 mm/min) ¹¹ | 54 | MPa | ISO 527 |
| Tensile Stress (Yield, Type I, 50 mm/min) ¹¹ | 59 | MPa | ASTM D638 |
| Tensile Strain (Break, 5 mm/min) ¹¹ | 46 | % | ISO 527 |
| Tensile Stress (Break, Type I, 50 mm/min) ¹¹ | 56 | MPa | ASTM D638 |
| Tensile Stress (Yield, 50 mm/min) ¹¹ | 55 | MPa | ISO 527 |
| Tensile Modulus (at 1 mm/min, at 120°C) ¹¹ | 2154 | MPa | ISO 527 |
| Tensile Strain (Yield, Type I, 50 mm/min) ¹¹ | 9 | % | ASTM D638 |
| Tensile Stress (Break, 50 mm/min) ¹¹ | 50 | MPa | ISO 527 |
| Flexural Modulus (at 2 mm/min) ¹¹ | 1900 | MPa | ISO 178 |
| Flexural Modulus (at 2 mm/min) ¹¹ | 2227 | MPa | ISO 178 |
Table 3 of 5
19 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Vicat Softening Temperature (Rate A/50) ¹¹ | 235 | °C | ISO 306 |
| Vicat Softening Temperature (Rate A/50) ¹¹ | 232 | °C | ASTM D1525 |
| Vicat Softening Temperature (Rate B/50) ¹¹ | 232 | °C | ASTM D1525 |
| Vicat Softening Temperature (Rate B/50) ¹¹ | 166 | °C | ISO 306 |
| Vicat Softening Temperature (Rate B/50) ¹¹ | 167 | °C | ASTM D1525 |
| Vicat Softening Temperature (Rate B/50) ¹¹ | 170 | °C | ISO 306 |
| Heat Deflection Temperature (at 0.45 MPa, 6.4 mm, Unannealed) ¹¹ | 155 | °C | ASTM D648 |
| Heat Deflection Temperature (at 1.82 MPa, 6.4 mm, Unannealed) ¹¹ | 127 | °C | ASTM D648 |
| Coefficient of Thermal Expansion (at -20°C to 150°C, flow) ¹¹ | 0.00009 | 1/°C | ASTM E831 |
| Heat Deflection Temperature/Af (at 1.8 Mpa, Flatw 80*10*4, sp=64mm) ¹¹ | 113 | °C | ISO 75/Af |
| Heat Deflection Temperature/Bf (at 0.45 Mpa, Flatw 80*10*4, sp=64mm) ¹¹ | 154 | °C | ISO 75/Bf |
| Coefficient of Thermal Expansion (at 23°C to 80°C, flow) ¹¹ | 0.000093 | 1/°C | ASTM E831 |
Table 4 of 5
19 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Izod Impact (Notched, 80*10*4, at 23°C) ¹¹ | 13 | kJ/m² | ISO 180/1A |
| Izod Impact (Notched, 80*10*4, at 23°C) ¹¹ | 18 | kJ/m² | ISO 180/1A |
| Izod Impact (Unnotched, at 23°C) ¹¹ | 3204 | J/m | ASTM D4812 |
| Izod Impact (Unnotched, at 23°C) ¹¹ | No break | J/m | ASTM D4812 |
| Izod Impact (Unnotched, 80*10*4, at 23°C) ¹¹ | DB | kJ/m² | ISO 180/1U |
| Izod Impact (Unnotched, at -30°C) ¹¹ | 3204 | J/m | ASTM D4812 |
| Izod Impact (Notched, at 23°C) ¹¹ | 272 | J/m | ASTM D256 |
| Izod Impact (Notched, at 23°C) ¹¹ | 167 | J/m | ASTM D256 |
| Izod Impact (Unnotched, at -40°C) ¹¹ | 3204 | J/m | ASTM D4812 |
| Izod Impact (Notched, at -40°C) ¹¹ | 53 | J/m | ASTM D256 |
| Izod Impact (Notched, at -30°C) ¹¹ | 117 | J/m | ASTM D256 |
| Charpy Impact (at 23°C, V-notch Edgew 80*10*4 sp=62mm) ¹¹ | 13 | kJ/m² | ISO 179/1eA |
Table 5 of 5
24 rows| Characteristic | Value | Unit |
|---|---|---|
| Drying Temperature ⁷ | 100 - 120 | °C |
| Drying Temperature ⁷ | 95 - 105 | °C |
| Drying Time ⁷ | 3 - 4 | Hrs |
| Drying Time ⁷ | 2 - 3 | Hrs |
| Drying Time (Cumulative) ⁷ | 8 | Hrs |
| Maximum Moisture Content ⁷ | 0.07 | % |
| Minimum Moisture Content ⁷ | 0.02 | % |
| Melt Temperature ⁷ | 280 - 310 | °C |
| Melt Temperature ⁷ | 275 - 300 | °C |
| Nozzle Temperature ⁷ | 275 - 300 | °C |
| Nozzle Temperature ⁷ | 270 - 300 | °C |
| Front - Zone 3 Temperature ⁷ | 280 - 300 | °C |
