NORYL™ Resin NHP9023
SABIC's Specialties Business NORYL NHP9023 resin is a 15% glass fiber reinforced blend of polyphenylene ether (PPE) + polystyrene (PS). This injection moldable grade contains non-brominated, non-chlorinated flame retardant and carries a UL94 flame rating of V0 1.5mm and V1 at 0.75mm for thin-wall molding capability. NORYL NHP9023 is based on a unique co-polymer technology and exhibits good dimensional stability, high heat resistance, strong electrical performance, and very low specific gravity. It is an excellent candidate for copier fuser units, business equipment internal components, and electrical applications where thin-wall FR, modulus retention, and high heat resistance are required. This product does not contain PFAS intentionally added during SHPP’s manufacturing process and are not expected to contain unintentional PFAS impurities. Each user is responsible for evaluating the presence of unintentional PFAS impurities.
Product families
Applications
- Consumer Goods — Appliances & Electronics
- Consumer Electronics
- Displays
- Connectors
- Switches & Relays
Product Families
- Blends & Alloys
Other characteristics
- Brand
- NORYL™ Resin
- Density
- 1210.0 - 1210.0 kg/m³
- Polymer Name
- PPO/PS Alloy
- Flexural Modulus
- 4900.0 - 4900.0 MPa
- Processing Methods
- Injection Molding
- Note
ᵍ Measurements made from Laboratory test Coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.; ʳ UL Ratings shown on the technical datasheet might not cover the full range of thicknesses, colors and regions. For details, please see the UL Yellow Card.; ⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.; ¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.; ¹⁵ Typical values only. Variations within normal tolerances are possible for various colors. All values are measured at least after 48 hours storage at 23°C/50% relative humidity. All properties, except the melt volume rate are measured on injection molded samples. All samples are prepared according to ISO 294. Only typical data for material selection purpose.Not to be used for part or tool design. The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.
- Markets
- Consumer Goods
- Electrical & Electronics
- Flame Rating
- UL 94 V0
- UL 94 V1
- Technology
- Plastics
- Labeling Claims
- Bromine-free
- Chlorine-free
- No Added PFAS
- Fillers Included
- Glass Fiber
- Additives Included
- Flame Retardant
- Heat Stabilizer
- Impact Modifier
- Material Features
- Amorphous
- Dimensional Stability
- Flame Retardant
- Good Processability
- Good Stiffness
- Heat Stabilized
- High Hydrolytic Stability
- High Stiffness
- Country Availability
- Canada
- China (Mainland)
- Mexico
- USA
- Certifications and Compliance
- UL 94
- Plastics and Elastomers End Uses
- Appliances
- Cell Phones
- Commercial Appliance
- Computer Components
- Connectors
- Displays
- Electrical Components
- Electrical/Electronic Applications
- Plastics and Elastomers Functions
- Resin
- Plastics and Elastomers Processing Methods
- Injection Molding
Technical data
Table 1 of 7
15 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Tensile Stress (Break, Type I, 5 mm/min) ¹⁵ | 112 | MPa | ASTM D638 |
| Tensile Strain (Break, Type I, 5 mm/min) ¹⁵ | 2.9 | % | ASTM D638 |
| Tensile Modulus (at 5 mm/min) ¹⁵ | 5400 | MPa | ASTM D638 |
| Flexural Stress (Yield, 1.3 mm/min, 50 mm span) ¹⁵ | 163 | MPa | ASTM D790 |
| Flexural Modulus (at 1.3 mm/min, 50 mm span) ¹⁵ | 5200 | MPa | ASTM D790 |
| Hardness (Rockwell R) ¹⁵ | 121 | — | ASTM D785 |
| Tensile Stress (Break, 5 mm/min) ¹⁵ | 90 | MPa | ISO 527 |
| Tensile Stress (Break, 5 mm/min) ¹⁵ | 112 | MPa | ISO 527 |
| Tensile Strain (Break, 5 mm/min) ¹⁵ | 2.7 | % | ISO 527 |
| Tensile Modulus (at 1 mm/min) ¹⁵ | 5500 | MPa | ISO 527 |
| Tensile Modulus (at 1 mm/min) ¹⁵ | 5600 | MPa | ISO 527 |
| Flexural Stress (Yield, at 2 mm/min) ¹⁵ | 140 | MPa | ISO 178 |
Table 2 of 7
9 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Specific Gravity ¹⁵ | 1.21 | — | ASTM D792 |
| Melt Flow Rate (at 300°C, 5.0 kgf) ¹⁵ | 20 | g/10 min | ASTM D1238 |
| Melt Volume Rate (at 280°C, 10.0 kg) ¹⁵ | 17 | cm³/10 min | ISO 1133 |
| Mold Shrinkage (flow, 3.2 mm) ᵍ ¹⁵ | 0.5 | % | SABIC method |
| Mold Shrinkage (on Tensile Bar, flow) ᵍ ¹⁵ | 0.38 | % | SABIC method |
| Density ¹⁵ | 1.21 | g/cm³ | ISO 1183 |
| Water Absorption (at 23°C, saturated) ¹⁵ | 0.2 | % | ISO 62-1 |
| Moisture Absorption (at 23°C, 50% RH) ¹⁵ | 0.05 | % | ISO 62 |
| Moisture Absorption (at 23°C, 50% RH) ¹⁵ | 0.11 | % | ISO 62 |
Table 3 of 7
13 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Heat Deflection Temperature (at 1.82 MPa, 6.4 mm, Unannealed) ¹⁵ | 153 | °C | ASTM D648 |
| Heat Deflection Temperature (at 1.82 MPa, 6.4 mm, Unannealed) ¹⁵ | 154 | °C | ASTM D648 |
| Heat Deflection Temperature (at 1.82 MPa, 3.2mm, Unannealed) ¹⁵ | 153 | °C | ASTM D648 |
| Vicat Softening Temperature (Rate B/120) ¹⁵ | 163 | °C | ISO 306 |
| Vicat Softening Temperature (Rate B/50) ¹⁵ | 161 | °C | ISO 306 |
| Coefficient of Thermal Expansion (at -40°C to 40°C, flow) ¹⁵ | 0.000038 | 1/°C | ISO 11359-2 |
| Coefficient of Thermal Expansion (at 23°C to 80°C, flow) ¹⁵ | 0.000035 | 1/°C | ISO 11359-2 |
| Coefficient of Thermal Expansion (at 23°C to 80°C, xflow) ¹⁵ | 0.000064 | 1/°C | ISO 11359-2 |
| Ball Pressure Test (at 123°C to 127°C) ¹⁵ | Pass | — | IEC 60695-10-2 |
| Heat Deflection Temperature/Af (at 1.8 Mpa, Flatw 80*10*4, sp=64mm) ¹⁵ | 155 | °C | ISO 75/Af |
| Relative Temperature Index (Electrical) ¹⁵ | 65 | °C | UL 746B |
| Relative Temperature Index (Mechanical with impact) ¹⁵ | 65 | °C | UL 746B |
Table 4 of 7
2 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Comparative Tracking Index ʳ ¹¹ | 175 | V | IEC 60112 |
| Comparative Tracking Index (UL, PLC) ¹¹ | 3 | PLC Code | UL 746A |
Table 5 of 7
13 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Izod Impact (Notched, at 23°C) ¹⁵ | 500 | J/m | ASTM D256 |
| Izod Impact (Notched, at 23°C) ¹⁵ | 72 | J/m | ASTM D256 |
| Charpy Impact (at -30°C, Unnotch Edgew 80*10*3 sp=62mm) ¹⁵ | 31 | kJ/m² | ISO 179/1eU |
| Charpy Impact (at 23°C, Unnotch Edgew 80*10*3 sp=62mm) ¹⁵ | 27 | kJ/m² | ISO 179/1eU |
| Charpy Impact (at 23°C, V-notch Edgew 80*10*4 sp=62mm) ¹⁵ | 7 | kJ/m² | ISO 179/1eA |
| Izod Impact (Unnotched, at 23°C) ¹⁵ | 500 | J/m | ASTM D4812 |
| Izod Impact (Unnotched, at -30°C) ¹⁵ | 500 | J/m | ASTM D4812 |
| Izod Impact (Notched, at -30°C) ¹⁵ | 61 | J/m | ASTM D256 |
| Instrumented Dart Impact Total Energy (at 23°C) ¹⁵ | 10 | J | ASTM D3763 |
| Izod Impact (Unnotched, 80*10*4, at 23°C) ¹⁵ | 27 | kJ/m² | ISO 180/1U |
| Izod Impact (Unnotched, 80*10*4, at -30°C) ¹⁵ | 28 | kJ/m² | ISO 180/1U |
| Izod Impact (Notched, 80*10*4, at 23°C) ¹⁵ | 7 | kJ/m² | ISO 180/1A |
Table 6 of 7
13 rows| Characteristic | Value | Unit |
|---|---|---|
| Drying Temperature ⁷ | 110 - 120 | °C |
| Drying Time ⁷ | 3 - 4 | Hrs |
| Drying Time (Cumulative) ⁷ | 8 | Hrs |
| Maximum Moisture Content ⁷ | 0.02 | % |
| Melt Temperature ⁷ | 300 - 325 | °C |
| Nozzle Temperature ⁷ | 300 - 325 | °C |
| Front - Zone 3 Temperature ⁷ | 290 - 325 | °C |
| Middle - Zone 2 Temperature ⁷ | 275 - 320 | °C |
| Rear - Zone 1 Temperature ⁷ | 265 - 315 | °C |
| Mold Temperature ⁷ | 80 - 110 | °C |
| Back Pressure ⁷ | 0.3 - 0.7 | MPa |
| Screw Speed ⁷ | 20 - 100 | rpm |
Table 7 of 7
3 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Glow Wire Flammability Index (passes at 960°C) ʳ | 3.2 | mm | IEC 60695-2-12 |
| UL Recognized (94V-1 Flame Class Rating) ʳ | min. 0.75 | mm | UL 94 |
| UL Recognized (94V-0 Flame Class Rating) ʳ | min. 1.5 | mm | UL 94 |
