LNP™ ELCRIN™ FXE8483RCC
- Chemical Family
- Polycarbonate (PC)Siloxanes
LNP™ ELCRIN™ FXE8483RCC is based on polycarbonate (pc) siloxane copolymer resin with a minimum of 75% post-consumer recycled (pcr) content. This grade features medium flow and is colorable, specifically designed for applications requiring enhanced esthetics and a broader color spectrum compared to traditional PCR grades. It is available in "Illuminate" and "Edge Glow" colors, offering VISUALFX capabilities to meet diverse application needs.
Product families
- Polycarbonates
Other characteristics
- Brand
- LNP™ ELCRIN
- Polymer Name
- Polycarbonate-Siloxane Copolymer
- Flexural Modulus
- 2300.0 - 2300.0 MPa
- Processing Methods
- Injection Molding
- Note
¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design. ² UL Ratings shown on the technical datasheet might not cover the full range of thicknesses and colors. For details, please see the UL Yellow Card. ³ Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article. ⁴ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.
- Technology
- Plastics
- Labeling Claims
- Contains PCR Resin
- No Added PFAS
- Sustainable
- Material Features
- Good Aesthetics
- Good Colorability
- Impact Resistance
- Medium Flow
- No Added PFAS
- Unreinforced
- Plastics and Elastomers Functions
- Resin
- Plastics and Elastomers Processing Methods
- Injection Molding
Technical data
Table 1 of 6
14 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Tensile Stress (Yield, 50 mm/min) ¹ | 62.0 | MPa | ISO 527 |
| Tensile Stress (Break, 50 mm/min) ¹ | 68.0 | MPa | ISO 527 |
| Tensile Strain (Yield, 50 mm/min) ¹ | 6.2 | % | ISO 527 |
| Tensile Strain (Break, 50 mm/min) ¹ | 140.0 | % | ISO 527 |
| Tensile Modulus (at 1 mm/min) ¹ | 2300.0 | MPa | ISO 527 |
| Flexural Modulus (at 2 mm/min) ¹ | 2300.0 | MPa | ISO 178 |
| Flexural Strength (2 mm/min) ¹ | 95.0 | MPa | ISO 178 |
| Tensile Modulus (at 50 mm/min) ¹ | 2200.0 | MPa | ASTM D638 |
| Tensile Stress (Yield, Type I, 50 mm/min) ¹ | 61.8 | MPa | ASTM D638 |
| Tensile Stress (Break, Type I, 50 mm/min) ¹ | 61.6 | MPa | ASTM D638 |
| Tensile Strain (Yield, Type I, 50 mm/min) ¹ | 6.3 | % | ASTM D638 |
| Tensile Strain (Break, Type I, 50 mm/min) ¹ | 116.0 | % | ASTM D638 |
Table 2 of 6
7 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Density ¹ | 1.19 | g/cm³ | ISO 1183 |
| Melt Volume Rate (at 300°C/1.2 kg) ¹ | 13.0 | cm³/10 min | ISO 1133 |
| Specific Gravity ¹ | 1.19 | — | ASTM D792 |
| Water Absorption (23°C/24hrs) ¹ | 0.16 | % | ASTM D570 |
| Mold Shrinkage (flow, 3.2 mm) ³ | 0.4 - 0.8 | % | SABIC method |
| Mold Shrinkage (xflow, 3.2 mm) ³ | 0.4 - 0.8 | % | SABIC method |
| Melt Flow Rate (at 300°C/1.2 kgf) ¹ | 15.0 | g/10 min | ASTM D1238 |
Table 3 of 6
12 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Heat Deflection Temperature/Af (1.8 MPa Flatw 80*10*4 sp=64mm) ¹ | 124.0 | °C | ISO 75/Af |
| Heat Deflection Temperature/Bf (0.45 MPa Flatw 80*10*4 sp=64mm) ¹ | 139.0 | °C | ISO 75/Bf |
| Vicat Softening Temperature (at Rate B/50) ¹ | 144.0 | °C | ISO 306 |
| Vicat Softening Temperature (at Rate B/50) ¹ | 144.0 | °C | ASTM D1525 |
| Vicat Softening Temperature (at Rate B/120) ¹ | 146.0 | °C | ISO 306 |
| Coefficient of Thermal Expansion (at 23°C to 80°C, flow) ¹ | 6.6e-05 | 1/°C | ISO 11359-2 |
| Coefficient of Thermal Expansion (at 23°C to 80°C, xflow) ¹ | 7.5e-05 | 1/°C | ISO 11359-2 |
| Heat Deflection Temperature (1.82 MPa, 3.2mm, unannealed) ¹ | 127.0 | °C | ASTM D648 |
| Heat Deflection Temperature (0.45 MPa, 3.2 mm, unannealed) ¹ | 140.0 | °C | ASTM D648 |
| Relative Temperature Index (Elec) ² | 80.0 | °C | UL 746B |
| Relative Temperature Index (Mech with impact) ² | 80.0 | °C | UL 746B |
| Relative Temperature Index (Mech w/o impact) ² | 80.0 | °C | UL 746B |
Table 4 of 6
6 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Izod Impact (Notched 80*10*4 +23°C) ¹ | 32.0 | kJ/m² | ISO 180/1A |
| Izod Impact (Unnotched 80*10*4 +23°C) ¹ | 137.0 | kJ/m² | ISO 180/1U |
| Charpy Impact (at 23°C, V-notch Edgew 80*10*3 sp=62mm) ¹ | 37.0 | kJ/m² | ISO 179/1eA |
| Charpy Impact (at 23°C, Unnotch Edgew 80*10*4 sp=62mm) ¹ | 125.0 | kJ/m² | ISO 179/1eU |
| Izod Impact (Notched, 23°C) ¹ | 750.0 | J/m | ASTM D256 |
| Izod Impact (Unnotched, 23°C) ¹ | 1730.0 | J/m | ASTM D4812 |
Table 5 of 6
11 rows| Characteristic | Value | Unit |
|---|---|---|
| Drying Temperature ⁴ | 120.0 | °C |
| Drying Time (Cumulative) ⁴ | 3 - 4 | Hrs |
| Maximum Moisture Content ⁴ | 0.02 | % |
| Nozzle Temperature ⁴ | 290 - 310 | °C |
| Melt Temperature ⁴ | 295 - 315 | °C |
| Front - Zone 3 Temperature ⁴ | 295 - 315 | °C |
| Middle - Zone 2 Temperature ⁴ | 280 - 305 | °C |
| Rear - Zone 1 Temperature ⁴ | 270 - 295 | °C |
| Mold Temperature ⁴ | 70 - 95 | °C |
| Back Pressure ⁴ | 0.3 - 0.7 | MPa |
| Screw Speed ⁴ | 40 - 70 | rpm |
Table 6 of 6
1 row| Characteristic | Value | Unit | Method |
|---|---|---|---|
| UL Recognized 94HB Flame Class Rating ² | 0.75 | mm | UL 94 |
