To catalogue
LNP™ LUBRICOMP™ Compound LL003XX1
- Chemical Family
- Polyether Ether Ketone (PEEK)
SABIC's Specialties Business LNP LUBRICOMP LL003XX1 compound is based on Polyetheretherketone (PEEK) resin containing 15% PTFE lubricant. Added features of this grade include: Easy Molding, Excellent Wear Resistance and Very Low Coefficient of Friction (CoF)
Product families
Applications
Applications
- Consumer Goods — Appliances & Electronics
- Consumer Goods — Lawn & Garden
- Consumer Goods — Sports & Recreation
Building & Construction — Decorative Materials & Finishes
- Artificial Turf
Electrical & Electronics — Devices & Assemblies
- Consumer Electronics
- Displays
Printing & Packaging — Packaging
- Non-Food Consumer Packaging
Personal Care — Packaging & Accessories
- Applicators & Accessories
Electrical & Electronics — Parts & Components
- Connectors
- Housings & Enclosures
- Switches & Relays
Automotive & Transportation — Transportation
- Aerospace & Aviation
Product Families
Plastics — Engineering & Specialty Polymers
- High Performance Thermoplastics
Other characteristics
- Brand
- LNP™ LUBRICOMP™ Compound
- Polymer Name
- Polyetheretherketone (PEEK)
- Fillers Included
- PTFE
- Flexural Modulus
- 2900.0 - 2900.0 MPa
- Additives Included
- Lubricant (PTFE), Lubricant (Unspecified)
- Lubricant (PTFE)
- Lubricant (Unspecified)
- Processing Methods
- Injection Molding
- Note
ᵍ Measurements made from Laboratory test Coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.; ⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.; ¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.
- Markets
- Automotive & Transportation
- Building & Construction
- Consumer Goods
- Electrical & Electronics
- Personal Care
- Printing & Packaging
- Technology
- Plastics
- Material Features
- Easy To Mold
- Friction Resistant
- Good Moldability
- Good Processability
- High Modulus
- High Strength
- High Temperature Resistance
- Low Coefficient of Friction
- Plastics and Elastomers End Uses
- Air Cabin Interior
- Appliances
- Building Materials
- Cell Phones
- Commercial Appliance
- Computer Components
- Consumer Applications
- Containers
- Plastics and Elastomers Functions
- Resin
- Plastics and Elastomers Processing Methods
- Injection Molding
Technical data
Table 1 of 6
8 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Dynamic COF ¹¹ | 0.29 | — | ASTM D3702 Modified: Manual |
| Static COF ¹¹ | 0.25 | — | ASTM D3702 Modified: Manual |
| Wear Factor Ring ¹¹ | 36 | 10^-10 in^5-min/ft-lb-hr | ASTM D3702 Modified: Manual |
| Specific Gravity ¹¹ | 1.36 | — | ASTM D792 |
| Mold Shrinkage (flow, 24 hrs) ᵍ ¹¹ | 0.3 - 0.4 | % | ASTM D955 |
| Mold Shrinkage (xflow, 24 hrs) ᵍ ¹¹ | 0.4 - 0.5 | % | ASTM D955 |
| Density ¹¹ | 1.36 | g/cm³ | ASTM D792 |
| Moisture Absorption (at 23°C, 50% RH) ¹¹ | 0.01 | % | ISO 62 |
Table 2 of 6
10 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Flexural Strength (at 1.3 mm/min, 50 mm span) ¹¹ | 121 | MPa | ASTM D790 |
| Flexural Modulus (at 1.3 mm/min, 50 mm span) ¹¹ | 3.10E+03 | MPa | ASTM D790 |
| Tensile Stress (Break, Type I, 5 mm/min) ¹¹ | 75 | MPa | ASTM D638 |
| Tensile Modulus (at 5 mm/min) ¹¹ | 3200 | MPa | ASTM D638 |
| Tensile Strain (Break, Type I, 5 mm/min) ¹¹ | 50 | % | ASTM D638 |
| Flexural Strength (at 2 mm/min) ¹¹ | 123 | MPa | ISO 178 |
| Flexural Modulus (at 2 mm/min) ¹¹ | 2900 | MPa | ISO 178 |
| Tensile Stress (Break, 5 mm/min) ¹¹ | 70 | MPa | ISO 527 |
| Tensile Modulus (at 1 mm/min) ¹¹ | 3100 | MPa | ISO 527 |
| Tensile Strain (Break, 5 mm/min) ¹¹ | 15 | % | ISO 527 |
Table 3 of 6
6 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Heat Deflection Temperature (at 1.82 MPa, 3.2mm, Unannealed) ¹¹ | 148 | °C | ASTM D648 |
| Heat Deflection Temperature (at 0.45 MPa, 3.2 mm, Unannealed) ¹¹ | 162 | °C | ASTM D648 |
| Heat Deflection Temperature/Af (at 1.8 Mpa, Flatw 80*10*4, sp=64mm) ¹¹ | 148 | °C | ISO 75/Af |
| Heat Deflection Temperature/Bf (at 0.45 Mpa, Flatw 80*10*4, sp=64mm) ¹¹ | 172 | °C | ISO 75/Bf |
| Coefficient of Thermal Expansion (at -40°C to 120°C, flow) ¹¹ | 0.000049 | 1/°C | ASTM E831 |
| Coefficient of Thermal Expansion (at -40°C to 120°C, xflow) ¹¹ | 0.000058 | 1/°C | ASTM E831 |
Table 4 of 6
4 rows| Characteristic | Value | Method |
|---|---|---|
| Dielectric Constant (at 1.1 GHz) ¹¹ | 3 | SABIC method |
| Dielectric Constant (at 1.9 GHz) ¹¹ | 2.60E-03 | SABIC method |
| Dissipation Factor (at 1.1 GHz) ¹¹ | 3.01 | SABIC method |
| Dissipation Factor (at 1.9 GHz) ¹¹ | 0.0028 | SABIC method |
Table 5 of 6
7 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Izod Impact (Notched, at 23°C) ¹¹ | 76 | J/m | ASTM D256 |
| Izod Impact (Unnotched, at 23°C) ¹¹ | 1230 | J/m | ASTM D4812 |
| Izod Impact (Notched, 80*10*4, at 23°C) ¹¹ | 7 | kJ/m² | ISO 180/1A |
| Izod Impact (Unnotched, 80*10*4, at 23°C) ¹¹ | 95 | kJ/m² | ISO 180/1U |
| Charpy Impact (at 23°C, V-notch Edgew 80*10*4 sp=62mm) ¹¹ | 7 | kJ/m² | ISO 179/1eA |
| Charpy Impact (at 23°C, Unnotch Edgew 80*10*4 sp=62mm) ¹¹ | 135 | kJ/m² | ISO 179/1eU |
| Multi-Axial Impact ¹¹ | 2.46 | J | ASTM D3763 |
Table 6 of 6
9 rows| Characteristic | Value | Unit |
|---|---|---|
| Drying Temperature ⁷ | 120 - 150 | °C |
| Drying Time ⁷ | 3 - 5 | Hrs |
| Nozzle Temperature ⁷ | 380 - 400 | °C |
| Melt Temperature ⁷ | 380 - 400 | °C |
| Front - Zone 3 Temperature ⁷ | 370 - 380 | °C |
| Middle - Zone 2 Temperature ⁷ | 360 - 370 | °C |
| Rear - Zone 1 Temperature ⁷ | 290 - 300 | °C |
| Mold Temperature ⁷ | 170 - 200 | °C |
| Screw Speed ⁷ | 50 - 100 | rpm |
