LNP™ LUBRICOMP™ Compound RAL23

Chemical Family: Polyamides

LNP LUBRICOMP RAL23 compound is based on Nylon 6/6 resin containing 15% aramid fiber, 10% PTFE. Added features of this grade include: Wear Resistant.

Product families

Applications

Consumer Goods — Appliances & Electronics
Consumer Goods — Lawn & Garden
Consumer Goods — Sports & Recreation

Automotive & Transportation — Automotive

Aftermarket Parts & Components
Cooling & Climate

Building & Construction — Decorative Materials & Finishes

Artificial Turf

Electrical & Electronics — Devices & Assemblies

Consumer Electronics
Displays

Printing & Packaging — Packaging

Non-Food Consumer Packaging

Personal Care — Packaging & Accessories

Applicators & Accessories

Electrical & Electronics — Parts & Components

Connectors
Housings & Enclosures
Switches & Relays

Product Families

Plastics — Engineering & Specialty Polymers

Polyamides

Other characteristics

Brand: LNP™ LUBRICOMP™ Compound
Polymer Name: Polyamide 66 (PA 66)
Fillers Included: Aramid Fiber, PTFE
Aramid Fiber
PTFE
Additives Included: Lubricant (PTFE)
Processing Methods: Injection Molding
Note: ᵍ Measurements made from Laboratory test Coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.; ⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.; ¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.
Markets: Automotive & Transportation
Building & Construction
Consumer Goods
Electrical & Electronics
Personal Care
Printing & Packaging
Technology: Plastics
Material Features: Low Slip
Wear Resistant
Typical Properties: Optimum plastic- plastic stick-slip performance
Vibration dampening characteristics
Abrasive wear resistance
Application in Mechatronics: Sensor
Sliders and actuators
Gear transmissions clutch systems
Bearings.
Typical Industry: Transmission efficiency; No noise; Good tribological performance when combined with glass fiber reinforced systems, used for structural performance; Avoidance grease at sub- zero temperatures
Plastics and Elastomers End Uses: Appliances
Building Materials
Cell Phones
Circuit Protection
Commercial Appliance
Computer Components
Consoles
Consumer Applications
Plastics and Elastomers Functions: Resin
Plastics and Elastomers Processing Methods: Injection Molding

Technical data

Table 1 of 5

10 rows

Characteristic	Value	Unit	Method
Tensile Stress (Break) ¹¹	89	MPa	ASTM D638
Tensile Stress (Break) ¹¹	85	MPa	ISO 527
Tensile Strain (Break) ¹¹	6.3	%	ISO 527
Tensile Strain (Break) ¹¹	5.9	%	ASTM D638
Tensile Modulus (at 5 mm/min) ¹¹	3680	MPa	ASTM D638
Flexural Stress ¹¹	131	MPa	ASTM D790
Flexural Stress ¹¹	107	MPa	ISO 178
Flexural Modulus ¹¹	3500	MPa	ISO 178
Flexural Modulus ¹¹	3930	MPa	ASTM D790
Tensile Modulus (at 1 mm/min) ¹¹	3800	MPa	ISO 527

Table 2 of 5

7 rows

Characteristic	Value	Unit	Method
Density ¹¹	1.23	g/cm³	ISO 1183
Density ¹¹	1.24	g/cm³	ASTM D792
Mold Shrinkage (flow, 24 hrs) ᵍ ¹¹	1 - 1.5	%	ASTM D955
Mold Shrinkage (xflow, 24 hrs) ᵍ ¹¹	1.2 - 1.7	%	ASTM D955
Wear Factor Washer ¹¹	23	10^-10 in^5-min/ft-lb-hr	ASTM D3702 Modified: Manual
Dynamic COF ¹¹	0.38	—	ASTM D3702 Modified: Manual
Static COF ¹¹	0.32	—	ASTM D3702 Modified: Manual

Table 3 of 5