NORYL GTX™ Resin GTX989
NORYL GTX™ Resin GTX989 is a conductive, non-reinforced alloy of polyphenylene ether (PPE) and polyamide (PA), for potential use in primer-less electrostatic painting. NORYL GTX989 Resin: Is well suited for primer-less electrostatic painting Exhibits high heat resistance Possesses high impact resistance Has a coefficient of thermal expansion (CTE) of approximately 9 NORYL GTX989 Resin is well suited for evaluation in painted automotive applications such as body panels, tank flaps, fenders, trunk lids, and exterior trim. This product does not contain PFAS intentionally added during SHPP’s manufacturing process. Each user is responsible for evaluating the presence of unintentional PFAS impurities.
Product families
Applications
- Electrical & Electronic Systems
- Exterior & Body
- Batteries
- Housings & Enclosures
Product Families
- Blends & Alloys
Other characteristics
- Brand
- NORYL GTX™ Resin
- Density
- 1080.0 - 1080.0 kg/m³
- Polymer Name
- PPO/Nylon Alloy
- Flexural Modulus
- 2370.0 - 2370.0 MPa
- Processing Methods
- Injection Molding
- Note
ᵍ Measurements made from Laboratory test Coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.; ⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.; ¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.
- Markets
- Automotive & Transportation
- Electrical & Electronics
- Technology
- Plastics
- Key Attributes
Low temperature impact strength; High heat resistance; Chemical resistance - Broad chemical resistance to commonly used automotive fuels, greases, and oils; On-line paint ability - Heat performance enables on-line painting; Good long-term dimensional stability; Class A surface appearance; Very low water absorption; Low creep behavior - Even in high-temperature environments
- Labeling Claims
- No Added PFAS
- Value Proposition
System cost reduction vs. metal solutions; Opportunity to paint within OEM paint-line; Widely used solution (currently in production on more than 60 different platforms)
- Additives Included
- Conductive Agent
- Heat Stabilizer
- Impact Modifier
- Material Features
- Chemical Resistant
- Conductive
- Dimensional Stability
- Electrically Conductive
- Excellent Aesthetics
- Good Aesthetics
- Good Surface Appearance
- Heat Stabilized
- HIGHLIGHTS
NORYL GTX™ conductive resins consist of blends of modified polyphenylene ether polymer (PPE) and polyamide (PA).; These blends combine the long-term dimensional stability, low water absorption, low specific gravity and heat resistance of PPE with the chemical resistance and flow of PA polymer.; The result is an extremely chemically resistant material with the stiffness, impact resistance and heat performance required for on-line painting.
- Country Availability
- Canada
- China (Mainland)
- Mexico
- USA
- Application Requirements
Class A surface appearance; Modulus (stiffness) over a range of temperatures: -40°C - 200°C; Dimensional stability; Chemical resistance; Online painting: conductive for electrostatic painting; Online painting: High HDT for e-coat and paint bake
- Plastics and Elastomers End Uses
- Automotive Exterior Parts
- Back Panel
- Battery Cover
- Corner Support Plates
- Crash Protection
- Front Panel
- Rocker Reinforcement
- Plastics and Elastomers Functions
- Resin
- Plastics and Elastomers Processing Methods
- Injection Molding
Technical data
Table 1 of 6
20 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Density ¹¹ | 1.08 | g/cm³ | ISO 1183 |
| Moisture Absorption (at 23°C, 50% RH, 24hrs) ¹¹ | 0.22 | % | ISO 62-4 |
| Moisture Absorption (at 23°C, 50% RH, Equilibrium) ¹¹ | 0.64 | % | ISO 62-4 |
| Water Absorption (at 23°C, 24hrs) ¹¹ | 0.83 | % | ISO 62-1 |
| Water Absorption (at 23°C, 24hrs) ¹¹ | 0.83 | % | ASTM D570 |
| Water Absorption (at 23°C, saturated) ¹¹ | 4.2 | % | ISO 62-1 |
| Water Absorption (at 23°C, saturated) ¹¹ | 2.29 | % | ISO 62-1 |
| Water Absorption (at 23°C, saturated) ¹¹ | 2.29 | % | ASTM D570 |
| Melt Volume Rate (at 280°C, 2.16 kg) ¹¹ | 4.6 | cm³/10 min | ISO 1133 |
| Melt Volume Rate (at 280°C, 5.0 kg) ¹¹ | 17 | cm³/10 min | ISO 1133 |
| Melt Volume Rate (at 280°C, 5.0 kg) ¹¹ | 19 | cm³/10 min | ISO 1133 |
| Specific Gravity ¹¹ | 1.08 | — | ASTM D792 |
Table 2 of 6
27 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Tensile Stress (Yield, 50 mm/min) ¹¹ | 62 | MPa | ISO 527 |
| Tensile Stress (Yield, 50 mm/min) ¹¹ | 60 | MPa | ISO 527 |
| Tensile Stress (Yield, Type I, 50 mm/min) ¹¹ | 65 | MPa | ASTM D638 |
| Tensile Stress (Yield, Type I, 50 mm/min) ¹¹ | 60 | MPa | ASTM D638 |
| Tensile Stress (Break, 50 mm/min) ¹¹ | 55 | MPa | ISO 527 |
| Tensile Stress (Break, 50 mm/min) ¹¹ | 57 | MPa | ISO 527 |
| Tensile Stress (Break, Type I, 50 mm/min) ¹¹ | 60 | MPa | ASTM D638 |
| Tensile Stress (Break, Type I, 50 mm/min) ¹¹ | 55 | MPa | ASTM D638 |
| Tensile Strain (Yield, 50 mm/min) ¹¹ | 5 | % | ISO 527 |
| Tensile Strain (Yield, Type I, 50 mm/min) ¹¹ | 5 | % | ASTM D638 |
| Tensile Strain (Yield, Type I, 50 mm/min) ¹¹ | 5.1 | % | ASTM D638 |
| Tensile Strain (Break, 50 mm/min) ¹¹ | 40 | % | ISO 527 |
Table 3 of 6
17 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Heat Deflection Temperature/Bf (at 0.45 Mpa, Flatw 80*10*4, sp=64mm) ¹¹ | 190 | °C | ISO 75/Bf |
| Heat Deflection Temperature/Af (at 1.8 Mpa, Flatw 80*10*4, sp=64mm) ¹¹ | 123 | °C | ISO 75/Af |
| Vicat Softening Temperature (Rate A/50) ¹¹ | 246 | °C | ISO 306 |
| Vicat Softening Temperature (Rate B/50) ¹¹ | 195 | °C | ISO 306 |
| Vicat Softening Temperature (Rate B/50) ¹¹ | 195 | °C | ASTM D1525 |
| Vicat Softening Temperature (Rate B/120) ¹¹ | 200 | °C | ISO 306 |
| Coefficient of Thermal Expansion (at 23°C to 60°C, flow) ¹¹ | 0.00009 | 1/°C | ISO 11359-2 |
| Coefficient of Thermal Expansion (at 23°C to 60°C, flow) ¹¹ | 0.000093 | 1/°C | ISO 11359-2 |
| Coefficient of Thermal Expansion (at 23°C to 60°C, flow) ¹¹ | 0.000093 | 1/°C | ASTM E831 |
| Coefficient of Thermal Expansion (at 23°C to 60°C, xflow) ¹¹ | 0.00009 | 1/°C | ISO 11359-2 |
| Coefficient of Thermal Expansion (at 23°C to 60°C, xflow) ¹¹ | 0.000095 | 1/°C | ISO 11359-2 |
| Coefficient of Thermal Expansion (at 23°C to 60°C, xflow) ¹¹ | 0.000095 | 1/°C | ASTM E831 |
Table 4 of 6
1 row| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Volume Resistivity ¹¹ | 1000 - 10000 | Ω.cm | SABIC method |
Table 5 of 6
12 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Izod Impact (Notched, 80*10*4, at 23°C) ¹¹ | 22 | kJ/m² | ISO 180/1A |
| Izod Impact (Notched, 80*10*4, at -30°C) ¹¹ | 15 | kJ/m² | ISO 180/1A |
| Izod Impact (Unnotched, 80*10*4, at 23°C) ¹¹ | No break | kJ/m² | ISO 180/1U |
| Charpy Impact (at 23°C, V-notch Edgew 80*10*4 sp=62mm) ¹¹ | 22 | kJ/m² | ISO 179/1eA |
| Charpy Impact (at 23°C, V-notch Edgew 80*10*4 sp=62mm) ¹¹ | 25 | kJ/m² | ISO 179/1eA |
| Charpy Impact (at -30°C, V-notch Edgew 80*10*4 sp=62mm) ¹¹ | 15 | kJ/m² | ISO 179/1eA |
| Charpy Impact (at 23°C, Unnotch Edgew 80*10*4 sp=62mm) ¹¹ | No break | kJ/m² | ISO 179/1eU |
| Izod Impact (Notched, at 23°C) ¹¹ | 240 | J/m | ASTM D256 |
| Izod Impact (Notched, at 23°C) ¹¹ | 251 | J/m | ASTM D256 |
| Izod Impact (Notched, at -30°C) ¹¹ | 180 | J/m | ASTM D256 |
| Izod Impact (Unnotched, at 23°C) ¹¹ | No break | J/m | ASTM D4812 |
| Instrumented Dart Impact Total Energy (at 23°C) ¹¹ | 60 | J | ASTM D3763 |
Table 6 of 6
11 rows| Characteristic | Value | Unit |
|---|---|---|
| Drying Temperature ⁷ | 100 - 120 | °C |
| Drying Time ⁷ | 2 - 3 | Hrs |
| Maximum Moisture Content ⁷ | 0.07 | % |
| Minimum Moisture Content ⁷ | 0.02 | % |
| Melt Temperature ⁷ | 290 - 320 | °C |
| Nozzle Temperature ⁷ | 280 - 310 | °C |
| Front - Zone 3 Temperature ⁷ | 290 - 320 | °C |
| Middle - Zone 2 Temperature ⁷ | 280 - 300 | °C |
| Rear - Zone 1 Temperature ⁷ | 260 - 280 | °C |
| Hopper Temperature ⁷ | 60 - 80 | °C |
| Mold Temperature ⁷ | 100 - 120 | °C |
