NORYL GTX™ Resin GTX975
SABIC's Specialties Business NORYL GTX975 resin is a conductive, 18% mineral reinforced alloy of Polyphenylene Ether (PPE) + Polyamide (PA). This injection moldable grade combines high stiffness and excellent temperature resistance with conductivity for primerless electrostatic painting. NORYL GTX975 was designed for in- or on-line painted exterior automotive trim parts such as tank flaps and corner panels. This product does not contain PFAS intentionally added during SHPP’s manufacturing process and are not expected to contain unintentional PFAS impurities. Each user is responsible for evaluating the presence of unintentional PFAS impurities.
Product families
Applications
- Electrical & Electronic Systems
- Exterior & Body
- Batteries
- Housings & Enclosures
Product Families
- Blends & Alloys
Other characteristics
- Brand
- NORYL GTX™ Resin
- Density
- 1250.0 - 1250.0 kg/m³
- Polymer Name
- PPO/Nylon Alloy
- Flexural Modulus
- 4000.0 - 4000.0 MPa
- Processing Methods
- Injection Molding
- Note
ᵍ Measurements made from Laboratory test Coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.; ⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.; ¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.
- Markets
- Automotive & Transportation
- Electrical & Electronics
- Technology
- Plastics
- Labeling Claims
- No Added PFAS
- Fillers Included
- Mineral
- Additives Included
- Conductive Agent
- Heat Stabilizer
- Impact Modifier
- Material Features
- Chemical Resistant
- Conductive
- Dimensional Stability
- Electrically Conductive
- Excellent Aesthetics
- Good Aesthetics
- Good Surface Appearance
- Heat Stabilized
- Country Availability
- Canada
- China (Mainland)
- Mexico
- USA
- Plastics and Elastomers End Uses
- Automotive Exterior Parts
- Back Panel
- Battery Cover
- Corner Support Plates
- Crash Protection
- Front Panel
- Rocker Reinforcement
- Plastics and Elastomers Functions
- Resin
- Plastics and Elastomers Processing Methods
- Injection Molding
Technical data
Table 1 of 6
15 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Tensile Stress (Break, 5 mm/min) ¹¹ | 65 | MPa | ISO 527 |
| Tensile Stress (Yield, Type I, 5 mm/min) ¹¹ | 69 | MPa | ASTM D638 |
| Tensile Strain (Break, 5 mm/min) ¹¹ | 4 | % | ISO 527 |
| Tensile Stress (Break, Type I, 5 mm/min) ¹¹ | 68 | MPa | ASTM D638 |
| Tensile Modulus (at 1 mm/min) ¹¹ | 4200 | MPa | ISO 527 |
| Tensile Strain (Yield, Type I, 5 mm/min) ¹¹ | 3.5 | % | ASTM D638 |
| Flexural Stress (Break, 2 mm/min) ¹¹ | 110 | MPa | ISO 178 |
| Tensile Strain (Break, Type I, 5 mm/min) ¹¹ | 4.5 | % | ASTM D638 |
| Flexural Modulus (at 2 mm/min) ¹¹ | 4000 | MPa | ISO 178 |
| Tensile Modulus (at 5 mm/min) ¹¹ | 4450 | MPa | ASTM D638 |
| Ball Indentation Hardness (H358/30) ¹¹ | 125 | MPa | ISO 2039-1 |
| Flexural Stress (Yield, 1.3 mm/min, 50 mm span) ¹¹ | 113 | MPa | ASTM D790 |
Table 2 of 6
8 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Mold Shrinkage (on Tensile Bar, flow) ᵍ ¹¹ | 1.1 - 1.3 | % | SABIC method |
| Density ¹¹ | 1.2 | g/cm³ | ISO 1183 |
| Melt Volume Rate (at 280°C, 5.0 kg) ¹¹ | 10 | cm³/10 min | ISO 1133 |
| Specific Gravity ¹¹ | 1.25 | — | ASTM D792 |
| Mold Shrinkage (flow, 3.2 mm) ᵍ ¹¹ | 0.8 - 1.2 | % | SABIC method |
| Melt Flow Rate (at 280°C, 5.0 kgf) ¹¹ | 15 | g/10 min | ASTM D1238 |
| Water Absorption (at 23°C, saturated) ¹¹ | 3.5 | % | ISO 62-1 |
| Moisture Absorption (at 23°C, 50% RH) ¹¹ | 1.1 | % | ISO 62 |
Table 3 of 6
9 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Coefficient of Thermal Expansion (at 23°C to 60°C, flow) ¹¹ | 0.00005 | 1/°C | ISO 11359-2 |
| Coefficient of Thermal Expansion (at 23°C to 60°C, xflow) ¹¹ | 0.000065 | 1/°C | ISO 11359-2 |
| Vicat Softening Temperature (Rate B/50) ¹¹ | 215 | °C | ASTM D1525 |
| Vicat Softening Temperature (Rate B/50) ¹¹ | 195 | °C | ISO 306 |
| Vicat Softening Temperature (Rate B/120) ¹¹ | 200 | °C | ISO 306 |
| Heat Deflection Temperature/Be (at 0.45MPa, Edgew 120*10*4, sp=100mm) ¹¹ | 185 | °C | ISO 75/Be |
| Heat Deflection Temperature (at 0.45 MPa, 3.2 mm, Unannealed) ¹¹ | 210 | °C | ASTM D648 |
| Coefficient of Thermal Expansion (at -40°C to 40°C, flow) ¹¹ | 0.000054 | 1/°C | ASTM E831 |
| Coefficient of Thermal Expansion (at -40°C to 40°C, xflow) ¹¹ | 0.00006 | 1/°C | ASTM E831 |
Table 4 of 6
1 row| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Volume Resistivity ¹¹ | 1000 - 10000 | Ω.cm | SABIC method |
Table 5 of 6
11 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Izod Impact (Unnotched, 80*10*4, at 23°C) ¹¹ | 40 | kJ/m² | ISO 180/1U |
| Izod Impact (Unnotched, 80*10*4, at -30°C) ¹¹ | 35 | kJ/m² | ISO 180/1U |
| Izod Impact (Notched, 80*10*4, at 23°C) ¹¹ | 4 | kJ/m² | ISO 180/1A |
| Izod Impact (Notched, 80*10*4, at -30°C) ¹¹ | 4 | kJ/m² | ISO 180/1A |
| Charpy Impact (at 23°C, V-notch Edgew 80*10*4 sp=62mm) ¹¹ | 3 | kJ/m² | ISO 179/1eA |
| Charpy Impact (at -30°C, V-notch Edgew 80*10*4 sp=62mm) ¹¹ | 3 | kJ/m² | ISO 179/1eA |
| Charpy Impact (at 23°C, Unnotch Edgew 80*10*4 sp=62mm) ¹¹ | 40 | kJ/m² | ISO 179/1eU |
| Charpy Impact (at -30°C, Unnotch Edgew 80*10*4 sp=62mm) ¹¹ | 35 | kJ/m² | ISO 179/1eU |
| Izod Impact (Notched, at 23°C) ¹¹ | 35 | J/m | ASTM D256 |
| Izod Impact (Notched, at -30°C) ¹¹ | 30 | J/m | ASTM D256 |
| Instrumented Dart Impact Total Energy (at 23°C) ¹¹ | 3 | J | ASTM D3763 |
Table 6 of 6
10 rows| Characteristic | Value | Unit |
|---|---|---|
| Drying Temperature ⁷ | 100 - 110 | °C |
| Drying Time ⁷ | 2 - 3 | Hrs |
| Maximum Moisture Content ⁷ | 0.02 | % |
| Melt Temperature ⁷ | 280 - 300 | °C |
| Nozzle Temperature ⁷ | 270 - 290 | °C |
| Front - Zone 3 Temperature ⁷ | 280 - 300 | °C |
| Middle - Zone 2 Temperature ⁷ | 270 - 290 | °C |
| Rear - Zone 1 Temperature ⁷ | 260 - 280 | °C |
| Hopper Temperature ⁷ | 80 - 100 | °C |
| Mold Temperature ⁷ | 100 - 120 | °C |
