NORYL GTX™ Resin GTX9500
SABIC's Specialties Business NORYL GTX9500 resin is a non-reinforced alloy of Polyphenylene Ether (PPE) + Polyamide (PA). This resin exhibits a good balance of high melt flow and low water absorption.Added features include excellent chemical resistance, high heat resistance, and dimensional stability.NORYL GTX9500 is an excellent candidate for various applications in the automotive and electronics industries.FeaturesChemical ResistantDimensional StabilityGood MoldabilityGood ProcessabilityGood StiffnessHigh Hydrolytic StabilityHigh Melt FlowLow CreepLow WarpageLow Water AbsorptionVery Good Heat ResistanceApplicationsAutomotive Exterior & BodyAutomotive InteriorPowertrain & UTHConnectorsSwitches & RelaysOff Road & Recreational Vehicle (RV)
Product families
Applications
- Aftermarket Parts & Components
- Electrical & Electronic Systems
- Exterior & Body
- Interior
- Powertrain & UTH
- Automotive Electronics
- Batteries
- Connectors
- Housings & Enclosures
- Switches & Relays
- Off Road & Recreational Vehicle (RV)
Product Families
- Blends & Alloys
Other characteristics
- Brand
- NORYL GTX™ Resin
- Density
- 1100.0 - 1100.0 kg/m³
- Polymer Name
- PPO/Nylon Alloy
- Flexural Modulus
- 2305.0 - 2305.0 MPa
- Processing Methods
- Injection Molding
- Note
ᵍ Measurements made from Laboratory test Coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.; ⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.; ¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.
- Markets
- Automotive & Transportation
- Electrical & Electronics
- Technology
- Plastics
- Additives Included
- Heat Stabilizer
- Impact Modifier
- Mold Release Agent
- Material Features
- Chemical Resistant
- Creep Resistant
- Dimensional Stability
- Good Mold Release
- Good Moldability
- Good Processability
- Good Stiffness
- Heat Stabilized
- Country Availability
- Canada
- China (Mainland)
- Mexico
- USA
- Plastics and Elastomers End Uses
- Automotive Applications
- Automotive Electronics
- Automotive Exterior Parts
- Automotive Under The Hood
- Back Panel
- Battery Cover
- Circuit Protection
- Consumer Applications
- Plastics and Elastomers Functions
- Resin
- Plastics and Elastomers Processing Methods
- Injection Molding
Technical data
Table 1 of 6
16 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Tensile Stress (Yield, Type I, 50 mm/min) ¹¹ | 61 | MPa | ASTM D638 |
| Tensile Stress (Break, Type I, 50 mm/min) ¹¹ | 57 | MPa | ASTM D638 |
| Tensile Strain (Yield, Type I, 50 mm/min) ¹¹ | 5 | % | ASTM D638 |
| Tensile Strain (Break, Type I, 50 mm/min) ¹¹ | 6 | % | ASTM D638 |
| Tensile Modulus (at 50 mm/min) ¹¹ | 2142 | MPa | ASTM D638 |
| Tensile Stress (Yield, 50 mm/min) ¹¹ | 60 | MPa | ISO 527 |
| Tensile Stress (Break, 50 mm/min) ¹¹ | 56 | MPa | ISO 527 |
| Tensile Strain (Yield, 50 mm/min) ¹¹ | 5 | % | ISO 527 |
| Tensile Strain (Break, 50 mm/min) ¹¹ | 9 | % | ISO 527 |
| Tensile Modulus (at 1 mm/min) ¹¹ | 2355 | MPa | ISO 527 |
| Flexural Stress (Yield, 1.3 mm/min, 50 mm span) ¹¹ | 90 | MPa | ASTM D790 |
| Flexural Modulus (at 1.3 mm/min, 50 mm span) ¹¹ | 2356.9 | MPa | ASTM D790 |
Table 2 of 6
6 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Specific Gravity ¹¹ | 1.1 | — | ASTM D792 |
| Mold Shrinkage (flow) ᵍ ¹¹ | 1.771 | % | SABIC method |
| Mold Shrinkage (xflow) ᵍ ¹¹ | 1.885 | % | SABIC method |
| Water Absorption (at 23°C, 48hrs) ¹¹ | 0.68 | % | ASTM D570 |
| Moisture Absorption (at 23°C, 50% RH) ¹¹ | 0.17 | % | ISO 62 |
| Melt Flow Rate (at 280°C, 2.16 kgf) ¹¹ | 28 | g/10 min | ASTM D1238 |
Table 3 of 6
12 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Heat Deflection Temperature (at 0.45 MPa, 3.2 mm, Unannealed) ¹¹ | 123 | °C | ASTM D648 |
| Heat Deflection Temperature (at 1.82 MPa, 3.2mm, Unannealed) ¹¹ | 65 | °C | ASTM D648 |
| Vicat Softening Temperature (Rate B/50) ¹¹ | 152 | °C | ASTM D1525 |
| Vicat Softening Temperature (Rate B/50) ¹¹ | 151 | °C | ISO 306 |
| Vicat Softening Temperature (Rate B/120) ¹¹ | 154 | °C | ISO 306 |
| Vicat Softening Temperature (Rate B/120) ¹¹ | 155.4 | °C | ASTM D1525 |
| Heat Deflection Temperature/Bf (at 0.45 Mpa, Flatw 80*10*4, sp=64mm) ¹¹ | 135.5 | °C | ISO 75/Bf |
| Heat Deflection Temperature/Af (at 1.8 Mpa, Flatw 80*10*4, sp=64mm) ¹¹ | 92.5 | °C | ISO 75/Af |
| Coefficient of Thermal Expansion (at -40°C to 40°C, flow) ¹¹ | 0.0000717 | 1/°C | ASTM E831 |
| Coefficient of Thermal Expansion (at -40°C to 40°C, xflow) ¹¹ | 0.0000755 | 1/°C | ASTM E831 |
| Coefficient of Thermal Expansion (at 23°C to 60°C, flow) ¹¹ | 0.0000862 | 1/°C | ISO 11359-2 |
| Coefficient of Thermal Expansion (at 23°C to 60°C, xflow) ¹¹ | 0.000102 | 1/°C | ISO 11359-2 |
Table 4 of 6
2 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Dielectric Strength (in oil, at 1.6mm) ¹¹ | 25.9 | kV/mm | ASTM D149 |
| Dissipation Factor (at at 1 MHz) ¹¹ | 0.01 | — | ASTM D150 |
Table 5 of 6
11 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Izod Impact (Notched, at 23°C) ¹¹ | 41 | J/m | ASTM D256 |
| Izod Impact (Notched, at -30°C) ¹¹ | 28 | J/m | ASTM D256 |
| Izod Impact (Unnotched, at 23°C) ¹¹ | 800 | J/m | ASTM D4812 |
| Instrumented Impact Total Energy (at 23°C) ¹¹ | 11 | J | ASTM D3763 |
| Instrumented Dart Impact Total Energy (at -30°C) ¹¹ | 4 | J | ASTM D3763 |
| Charpy Impact (Notched, at 23°C, 80*10*4mm, Cut) ¹¹ | 7 | kJ/m² | ISO 179/1eA |
| Charpy Impact (Notched, at -30°C, 80*10*4mm, Cut) ¹¹ | 6 | kJ/m² | ISO 179/1eA |
| Charpy Impact (Unnotched, at 23°C) ¹¹ | 51 | kJ/m² | ISO 179/2C |
| Izod Impact (Notched, 80*10*4, at 23°C) ¹¹ | 5 | kJ/m² | ISO 180/1A |
| Izod Impact (Notched, 80*10*4, at -30°C) ¹¹ | 5 | kJ/m² | ISO 180/1A |
| Izod Impact (Unnotched, 80*10*3, at 23°C) ¹¹ | 64 | kJ/m² | ISO 180/1U |
Table 6 of 6
15 rows| Characteristic | Value | Unit |
|---|---|---|
| Drying Temperature ⁷ | 95 - 105 | °C |
| Drying Time ⁷ | 3 - 4 | Hrs |
| Drying Time (Cumulative) ⁷ | 8 | Hrs |
| Maximum Moisture Content ⁷ | 0.07 | % |
| Minimum Moisture Content ⁷ | 0.02 | % |
| Melt Temperature ⁷ | 270 - 295 | °C |
| Nozzle Temperature ⁷ | 270 - 295 | °C |
| Front - Zone 3 Temperature ⁷ | 265 - 295 | °C |
| Middle - Zone 2 Temperature ⁷ | 260 - 295 | °C |
| Rear - Zone 1 Temperature ⁷ | 255 - 295 | °C |
| Mold Temperature ⁷ | 65 - 95 | °C |
| Back Pressure ⁷ | 0.3 - 1.4 | MPa |
