NORYL GTX™ Resin GTX910
SABIC's Specialties Business NORYL GTX910 resin is a non-reinforced alloy of Polyphenylene Ether (PPE) + Polyamide (PA). NORYL GTX910 resin exhibits excellent chemical resistance and is an excellent candidate for automotive applications such as plastic/metal hybrid components, rail extensions, crash cans, wheel covers, and energy absorbers. This product does not contain PFAS intentionally added during SHPP’s manufacturing process and are not expected to contain unintentional PFAS impurities. Each user is responsible for evaluating the presence of unintentional PFAS impurities.
Product families
- Blends & Alloys
Other characteristics
- Brand
- NORYL GTX™ Resin
- Density
- 1107.0 - 1107.0 kg/m³
- Polymer Name
- PPO/Nylon Alloy
- Processing Methods
- Injection Molding
- Note
ᵍ Measurements made from Laboratory test Coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.; ⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.; ¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.; ᵖ UL ratings shown on the technical datasheet might not cover the full range of thicknesses and colors. For details, please see the UL Yellow Card.
- Markets
- Automotive & Transportation
- Building & Construction
- Consumer Goods
- Electrical & Electronics
- Flame Rating
- UL 94 HB
- Technology
- Plastics
- Labeling Claims
- No Added PFAS
- Additives Included
- Heat Stabilizer
- Impact Modifier
- Material Features
- Chemical Resistant
- Dimensional Stability
- Heat Resistance
- Heat Stabilized
- High Hydrolytic Stability
- High Impact Resistance
- High Stiffness
- High Temperature Strength
- Country Availability
- Canada
- China (Mainland)
- Mexico
- USA
- Certifications and Compliance
- UL 94
- Plastics and Elastomers End Uses
- Automotive Applications
- Automotive Exterior Parts
- Back Panel
- Battery Cover
- Building Materials
- Corner Support Plates
- Covers
- Crash Protection
- Plastics and Elastomers Functions
- Resin
- Plastics and Elastomers Processing Methods
- Injection Molding
Technical data
Table 1 of 7
15 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Taber Abrasion (CS-17, 1 kg) ¹¹ | 15 | mg/1000cy | SABIC method |
| Tensile Stress (Yield, Type I, 50 mm/min) ¹¹ | 59 | MPa | ASTM D638 |
| Tensile Stress (Break, Type I, 50 mm/min) ¹¹ | 55 | MPa | ASTM D638 |
| Tensile Stress (Yield, 50 mm/min) ¹¹ | 55 | MPa | ISO 527 |
| Tensile Strain (Break, Type I, 50 mm/min) ¹¹ | 60 | % | ASTM D638 |
| Tensile Stress (Break, 50 mm/min) ¹¹ | 50 | MPa | ISO 527 |
| Flexural Stress (Yield, 2.6 mm/min, 100 mm span) ¹¹ | 95 | MPa | ASTM D790 |
| Tensile Strain (Yield, 50 mm/min) ¹¹ | 8 | % | ISO 527 |
| Flexural Modulus (at 2.6 mm/min, 100 mm span) ¹¹ | 2240 | MPa | ASTM D790 |
| Tensile Strain (Break, 50 mm/min) ¹¹ | 25 | % | ISO 527 |
| Hardness (Rockwell R) ¹¹ | 116 | — | ASTM D785 |
| Tensile Modulus (at 1 mm/min) ¹¹ | 2200 | MPa | ISO 527 |
Table 2 of 7
12 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Specific Gravity ¹¹ | 1.1 | — | ASTM D792 |
| Density ¹¹ | 1.1 | g/cm³ | ISO 1183 |
| Density ¹¹ | 1.107 | g/cm³ | ASTM D792 |
| Moisture Absorption (at 50% RH, Equilibrium) ¹¹ | 1 | % | ASTM D570 |
| Moisture Absorption (at 23°C, 50% RH, 24hrs) ¹¹ | 0.5 | % | ASTM D570 |
| Mold Shrinkage (on Tensile Bar, flow) ᵍ ¹¹ | 1.2 - 1.6 | % | SABIC method |
| Mold Shrinkage (flow, 3.2 mm) ᵍ ¹¹ | 1.1 - 1.3 | % | SABIC method |
| Mold Shrinkage (flow, annealed, at 130°C, 1hr) ᵍ ¹¹ | 1.6 - 1.8 | % | ASTM D955 |
| Water Absorption (at 23°C, saturated) ¹¹ | 3.5 | % | ISO 62-1 |
| Moisture Absorption (at 23°C, 50% RH) ¹¹ | 1 | % | ISO 62 |
| Mold Shrinkage (xflow, 3.2 mm) ᵍ ¹¹ | 1 - 1.2 | % | SABIC method |
| Melt Volume Rate (at 280°C, 5.0 kg) ¹¹ | 10 | cm³/10 min | ISO 1133 |
Table 3 of 7
15 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Vicat Softening Temperature (Rate B/50) ¹¹ | 232 | °C | ASTM D1525 |
| Vicat Softening Temperature (Rate B/50) ¹¹ | 195 | °C | ISO 306 |
| Heat Deflection Temperature (at 0.45 MPa, 6.4 mm, Unannealed) ¹¹ | 193 | °C | ASTM D648 |
| Heat Deflection Temperature (at 1.82 MPa, 6.4 mm, Unannealed) ¹¹ | 143 | °C | ASTM D648 |
| Coefficient of Thermal Expansion (at -40°C to 95°C, flow) ¹¹ | 0.00009 | 1/°C | ASTM E831 |
| Coefficient of Thermal Expansion (at -40°C to 95°C, xflow) ¹¹ | 0.00009 | 1/°C | ASTM E831 |
| Coefficient of Thermal Expansion (at 60°C to 138°C, flow) ¹¹ | 0.000126 | 1/°C | ASTM E831 |
| Thermal Conductivity ¹¹ | 0.23 | W/m-°C | ISO 8302 |
| Coefficient of Thermal Expansion (at 23°C to 60°C, flow) ¹¹ | 0.00009 | 1/°C | ISO 11359-2 |
| Coefficient of Thermal Expansion (at 60°C to 138°C, xflow) ¹¹ | 0.000126 | 1/°C | ASTM E831 |
| Coefficient of Thermal Expansion (at 23°C to 60°C, xflow) ¹¹ | 0.00009 | 1/°C | ISO 11359-2 |
| Ball Pressure Test (at 123°C to 127°C) ¹¹ | Pass | — | IEC 60695-10-2 |
Table 4 of 7
5 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Comparative Tracking Index (UL, PLC) ¹¹ | 1 | PLC Code | UL 746A |
| High Ampere Arc Ignition (PLC 0) ¹¹ | min. 1.5 | mm | UL 746A |
| Hot Wire Ignition (PLC 3) ¹¹ | min. 1.5 | mm | UL 746A |
| High Voltage Arc Track Rate (PLC) ¹¹ | 4 | PLC Code | UL 746A |
| Arc Resistance (Tungsten, PLC) ¹¹ | 7 | PLC Code | ASTM D495 |
Table 5 of 7
10 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Izod Impact (Notched, at 23°C) ¹¹ | 240 | J/m | ASTM D256 |
| Izod Impact (Notched, at -30°C) ¹¹ | 133 | J/m | ASTM D256 |
| Instrumented Dart Impact Energy (Peak, at 23°C) ¹¹ | 50 | J | ASTM D3763 |
| Instrumented Dart Impact Energy (Peak, at -30°C) ¹¹ | 39 | J | ASTM D3763 |
| Izod Impact (Notched, 80*10*4, at 23°C) ¹¹ | 25 | kJ/m² | ISO 180/1A |
| Izod Impact (Notched, 80*10*4, at -30°C) ¹¹ | 12 | kJ/m² | ISO 180/1A |
| Charpy Impact (at 23°C, V-notch Edgew 80*10*4 sp=62mm) ¹¹ | 25 | kJ/m² | ISO 179/1eA |
| Charpy Impact (Notched, at 23°C) ¹¹ | 25 | kJ/m² | ISO 179/2C |
| Charpy Impact (at -30°C, V-notch Edgew 80*10*4 sp=62mm) ¹¹ | 12 | kJ/m² | ISO 179/1eA |
| Charpy Impact (Notched, at -20°C) ¹¹ | 9 | kJ/m² | ISO 179/2C |
Table 6 of 7
24 rows| Characteristic | Value | Unit |
|---|---|---|
| Drying Temperature ⁷ | 100 - 120 | °C |
| Drying Temperature ⁷ | 95 - 105 | °C |
| Drying Time ⁷ | 3 - 4 | Hrs |
| Drying Time ⁷ | 2 - 3 | Hrs |
| Drying Time (Cumulative) ⁷ | 8 | Hrs |
| Maximum Moisture Content ⁷ | 0.07 | % |
| Melt Temperature ⁷ | 280 - 305 | °C |
| Melt Temperature ⁷ | 280 - 310 | °C |
| Minimum Moisture Content ⁷ | 0.02 | % |
| Nozzle Temperature ⁷ | 280 - 305 | °C |
| Nozzle Temperature ⁷ | 270 - 300 | °C |
| Front - Zone 3 Temperature ⁷ | 280 - 300 | °C |
Table 7 of 7
2 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| UL Compliant (94HB Flame Class Rating) ᵖ | 1.6 | mm | UL 94 by SABIC-IP |
| UL Recognized (94HB Flame Class Rating) ᵖ | min. 1.5 | mm | UL 94 |
