NORYL GTX™ Resin GTX820
SABIC's Specialties Business NORYL GTX820 resin is a 20% glass fiber reinforced alloy of Polyphenylene Ether (PPE) + Polyamide (PA). This injection moldable grade has high stiffness (flexural modulus 4000 MPa), excellent chemical resistance, and high heat resistance. NORYL GTX820 resin is an excellent candidate for a wide variety of applications including valves for water management. This product does not contain PFAS intentionally added during SHPP’s manufacturing process and are not expected to contain unintentional PFAS impurities. Each user is responsible for evaluating the presence of unintentional PFAS impurities.
Product families
- Blends & Alloys
Other characteristics
- Brand
- NORYL GTX™ Resin
- Density
- 1240.0 - 1240.0 kg/m³
- Polymer Name
- PPO/Nylon Alloy
- Flexural Modulus
- 5960.0 - 5960.0 MPa
- Processing Methods
- Injection Molding
- Note
ᶜ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding. Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.; ᵍ Measurements made from Laboratory test Coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.; ᵖ UL ratings shown on the technical datasheet might not cover the full range of thicknesses and colors. For details, please see the UL Yellow Card.; ʳ UL Ratings shown on the technical datasheet might not cover the full range of thicknesses, colors and regions. For details, please see the UL Yellow Card.; ⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.; ¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.; ¹⁸ UL Ratings shown on the technical datasheet might not cover the full range of thicknesses, colors and regions. For details, please see the UL Yellow Card. The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.
- Markets
- Automotive & Transportation
- Building & Construction
- Electrical & Electronics
- Flame Rating
- UL 94 HB
- Technology
- Plastics
- Labeling Claims
- No Added PFAS
- Fillers Included
- Glass Fiber
- Additives Included
- Heat Stabilizer
- Impact Modifier
- Material Features
- Chemical Resistant
- Dimensional Stability
- Heat Stabilized
- High Hydrolytic Stability
- High Stiffness
- High Strength
- High Tensile Strength
- Impact Modified
- Country Availability
- Canada
- China (Mainland)
- Mexico
- USA
- Certifications and Compliance
- UL 94
- Plastics and Elastomers End Uses
- Automotive Electronics
- Automotive Under The Hood
- Back Panel
- Battery Cover
- Connectors
- Corner Support Plates
- Crash Protection
- Electrical/Electronic Applications
- Plastics and Elastomers Functions
- Resin
Technical data
Table 1 of 7
21 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Density ¹¹ | 1.25 | g/cm³ | ISO 1183 |
| Density ¹¹ | 1.24 | g/cm³ | ASTM D792 |
| Moisture Absorption (at 23°C, 50% RH) ¹¹ | 1.08 | % | ISO 62 |
| Specific Gravity ¹¹ | 1.24 | — | ASTM D792 |
| Water Absorption (at 23°C, 24hrs) ¹¹ | 0.7 | % | ISO 62-1 |
| Water Absorption (at 23°C, 24hrs) ¹¹ | 0.7 | % | ASTM D570 |
| Water Absorption (at 23°C, saturated) ¹¹ | 3.2 | % | ISO 62-1 |
| Water Absorption (at 23°C, saturated) ¹¹ | 1.88 | % | ASTM D570 |
| Water Absorption (at 23°C, saturated) ¹¹ | 1.88 | % | ISO 62-1 |
| Melt Flow Rate (at 280°C, 5.0 kgf) ¹¹ | 7 | g/10 min | ASTM D1238 |
| Melt Volume Rate (at 280°C, 5.0 kg) ¹¹ | 6 | cm³/10 min | ISO 1133 |
| Melt Volume Rate (at 280°C, 5.0 kg) ¹¹ | 7.1 | cm³/10 min | ISO 1133 |
Table 2 of 7
24 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Tensile Stress (Yield, 5 mm/min) ¹¹ | 100 | MPa | ISO 527 |
| Tensile Stress (Break, 5 mm/min) ¹¹ | 95 | MPa | ISO 527 |
| Tensile Stress (Break, 5 mm/min) ¹¹ | 139 | MPa | ISO 527 |
| Tensile Stress (Yield, Type I, 5 mm/min) ¹¹ | 117 | MPa | ASTM D638 |
| Tensile Strain (Yield, 5 mm/min) ¹¹ | 2.5 | % | ISO 527 |
| Tensile Stress (Break, Type I, 5 mm/min) ¹¹ | 117 | MPa | ASTM D638 |
| Tensile Stress (Break, Type I, 5 mm/min) ¹¹ | 133 | MPa | ASTM D638 |
| Tensile Strain (Break, 5 mm/min) ¹¹ | 3.5 | % | ISO 527 |
| Tensile Strain (Break, 5 mm/min) ¹¹ | 3.6 | % | ISO 527 |
| Tensile Strain (Break, Type I, 5 mm/min) ¹¹ | 7 | % | ASTM D638 |
| Tensile Strain (Break, Type I, 5 mm/min) ¹¹ | 3.6 | % | ASTM D638 |
| Tensile Modulus (at 5 mm/min) ¹¹ | 6350 | MPa | ASTM D638 |
Table 3 of 7
21 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Heat Deflection Temperature (at 1.82 MPa, 6.4 mm, Unannealed) ¹¹ | 232 | °C | ASTM D648 |
| Heat Deflection Temperature (at 0.45 MPa, 6.4 mm, Unannealed) ¹¹ | 254 | °C | ASTM D648 |
| Vicat Softening Temperature (Rate B/50) ¹¹ | 215 | °C | ISO 306 |
| Vicat Softening Temperature (Rate B/50) ¹¹ | 231 | °C | ASTM D1525 |
| Vicat Softening Temperature (Rate B/50) ¹¹ | 248 | °C | ASTM D1525 |
| Vicat Softening Temperature (Rate B/50) ¹¹ | 229 | °C | ISO 306 |
| Coefficient of Thermal Expansion (at 23°C to 60°C, flow) ¹¹ | 0.000027 | 1/°C | ISO 11359-2 |
| Coefficient of Thermal Expansion (at 23°C to 60°C, flow) ¹¹ | 0.000027 | 1/°C | ASTM E831 |
| Coefficient of Thermal Expansion (at 23°C to 60°C, xflow) ¹¹ | 0.000078 | 1/°C | ISO 11359-2 |
| Coefficient of Thermal Expansion (at 23°C to 60°C, xflow) ¹¹ | 0.000078 | 1/°C | ASTM E831 |
| Coefficient of Thermal Expansion (at -20°C to 150°C, flow) ¹¹ | 0.000031 - 0.00004 | 1/°C | ASTM E831 |
| Coefficient of Thermal Expansion (at -20°C to 150°C, flow) ¹¹ | 0.0000306 - 0.0000396 | 1/°C | ASTM E831 |
Table 4 of 7
4 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Comparative Tracking Index (UL, PLC) ¹⁸ | 2 | PLC Code | UL 746A |
| Hot Wire Ignition (PLC 0) ¹⁸ | 1.5 | mm | UL 746A |
| High Ampere Arc Ignition (PLC 1) ¹⁸ | 1.5 | mm | UL 746A |
| Arc Resistance (Tungsten, PLC) ¹⁸ | 6 | PLC Code | ASTM D495 |
Table 5 of 7
13 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| Izod Impact (Unnotched, 80*10*4, at 23°C) ¹¹ | 40 | kJ/m² | ISO 180/1U |
| Izod Impact (Unnotched, 80*10*4, at 23°C) ¹¹ | 86 | kJ/m² | ISO 180/1U |
| Izod Impact (Unnotched, 80*10*4, at -30°C) ¹¹ | 40 | kJ/m² | ISO 180/1U |
| Charpy Impact (Notched, at 23°C) ¹¹ | 7 | kJ/m² | ISO 179/2C |
| Charpy Impact (Notched, at -20°C) ¹¹ | 5 | kJ/m² | ISO 179/2C |
| Charpy Impact (at 23°C, Unnotch Edgew 80*10*4 sp=62mm) ¹¹ | 50 | kJ/m² | ISO 179/1eU |
| Charpy Impact (at 23°C, Unnotch Edgew 80*10*4 sp=62mm) ¹¹ | 62 | kJ/m² | ISO 179/1eU |
| Charpy Impact (at -30°C, Unnotch Edgew 80*10*4 sp=62mm) ¹¹ | 40 | kJ/m² | ISO 179/1eU |
| Izod Impact (Notched, at 23°C) ¹¹ | 93 | J/m | ASTM D256 |
| Izod Impact (Unnotched, at 23°C) ¹¹ | 900 | J/m | ASTM D4812 |
| Izod Impact (Notched, at -30°C) ¹¹ | 53 | J/m | ASTM D256 |
| Izod Impact (Notched, 80*10*4, at 23°C) ¹¹ | 8.8 | kJ/m² | ISO 180/1A |
Table 6 of 7
24 rows| Characteristic | Value | Unit |
|---|---|---|
| Drying Temperature ⁷ | 100 - 110 | °C |
| Drying Temperature ⁷ | 95 - 105 | °C |
| Drying Time ⁷ | 3 - 4 | Hrs |
| Drying Time ⁷ | 2 - 3 | Hrs |
| Drying Time (Cumulative) ⁷ | 8 | Hrs |
| Maximum Moisture Content ⁷ | 0.07 | % |
| Minimum Moisture Content ⁷ | 0.02 | % |
| Melt Temperature ⁷ | 280 - 305 | °C |
| Melt Temperature ⁷ | 280 - 300 | °C |
| Nozzle Temperature ⁷ | 280 - 305 | °C |
| Nozzle Temperature ⁷ | 270 - 290 | °C |
| Front - Zone 3 Temperature ⁷ | 280 - 300 | °C |
Table 7 of 7
2 rows| Characteristic | Value | Unit | Method |
|---|---|---|---|
| UL Recognized (94HB Flame Class Rating) ʳ | min. 1.5 | mm | UL 94 |
| Oxygen Index (LOI) ʳ | 26 | % | ISO 4589 |
