NORYL™ Resin SE100X

Chemical Family: PolyethersStyrenics

NORYL™ Resin SE100X is a non-reinforced blend of polyphenylene ether (PPE) and high-impact polystyrene (HIPS). This injection moldable grade features non-brominated, non-chlorinated flame retardants, achieving a UL94 flame rating of V0 at 6 mm and V1 at 1.5 mm, complemented by a UL746C outdoor suitability rating of F1. NORYL™ Resin SE100X excels in electrical performance, boasting low moisture absorption, excellent flow properties, dimensional stability, and hydrolytic stability. Specifically engineered for both indoor and outdoor applications, including electrical enclosures, wall plates, sockets, switches, and connectors, NORYL™ Resin SE100X offers manufacturers a reliable material solution capable of meeting stringent safety standards while maintaining robust performance across diverse environmental conditions.

Product families

Applications

Consumer Goods — Appliances & Electronics
Consumer Goods — Housewares
Consumer Goods — Lawn & Garden

Building & Construction — Building Materials

Pipes & Plumbing
Structural Components

Electrical & Electronics — Devices & Assemblies

Consumer Electronics

Electrical & Electronics — Parts & Components

Connectors
Housings & Enclosures
Terminal Blocks Plugs & Sockets

Product Families

Plastics — Engineering & Specialty Polymers

Blends & Alloys

Other characteristics

Brand: NORYL™ Resin
Density: 1100.0 - 1100.0 kg/m³
Polymer Name: PPE/HIPS Alloy
Flexural Modulus: 2300.0 - 2300.0 MPa
Processing Methods: Injection Molding
Note: (1) The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design. (2) UL Ratings shown on the technical datasheet might not cover the full range of thicknesses and colors. For details, please see the UL Yellow Card. (3) Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article. (4) Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.
Markets: Building & Construction
Consumer Goods
Electrical & Electronics
Flame Rating: UL 94 V0
UL 94 V1
Technology: Plastics
Quality Standards: UL 746C
Material Features: Amorphous
Creep Resistant
Flame Retardant
Good Processability
Good UV Stability
Good Weather Stability
High Flow
High Hydrolytic Stability
Certifications and Compliance: UL 94
Plastics and Elastomers End Uses: Building Materials
Commercial Appliance
Connectors
Electrical Components
Home Appliances
Indoor Enclosure
Outdoor Enclosure
Sockets
Plastics and Elastomers Functions: Resin
Plastics and Elastomers Processing Methods: Injection Molding

Technical data

Table 1 of 7

6 rows

Characteristic	Value	Unit	Method
Tensile Stress (Yield, Type I, 50 mm/min) ¹	57.0	MPa	ASTM D638
Tensile Stress (Break, Type I, 50 mm/min) ¹	46.0	MPa	ASTM D638
Tensile Strain (Yield, Type I, 50 mm/min) ¹	6.5	%	ASTM D638
Tensile Strain (Break, Type I, 50 mm/min) ¹	25.0	%	ASTM D638
Flexural Stress (Yield, 2.6 mm/min, 100 mm span) ¹	82.0	MPa	ASTM D790
Flexural Modulus (at 2.6 mm/min, 100 mm span) ¹	2300.0	MPa	ASTM D790

Table 2 of 7

3 rows

Characteristic	Value	Unit	Method
Specific Gravity ¹	1.1	—	ASTM D792
Mold Shrinkage (flow, 3.2 mm) ³	0.5 - 0.7	%	SABIC method
Mold Shrinkage (on Tensile Bar, xflow) ³	0.5 - 0.7	%	SABIC method

Table 3 of 7

5 rows

Characteristic	Value	Unit	Method
Heat Deflection Temperature, 0.45 MPa, 6.4 mm, unannealed ¹	102.0	°C	ASTM D648
Heat Deflection Temperature (1.82 MPa, 6.4 mm, unannealed) ¹	92.0	°C	ASTM D648
Relative Temperature Index (Elec) ²	95.0	°C	UL 746B
Relative Temperature Index (Mech with impact) ²	80.0	°C	UL 746B
Relative Temperature Index (Mech w/o impact) ²	95.0	°C	UL 746B

Table 4 of 7

13 rows

Characteristic	Value	Unit	Method
Volume Resistivity ¹	3.1e+16	Ω.cm	ASTM D257
Surface Resistivity ¹	min. 1.E+15	Ω	ASTM D257
Dielectric Strength (in oil, 3.2 mm) ¹	17.9	kV/mm	ASTM D149
Relative Permittivity (at 50/60 Hz) ¹	2.66	—	ASTM D150
Relative Permittivity (at 1 MHz) ¹	2.57	—	ASTM D150
Dissipation Factor (at 50/60 Hz) ¹	0.006	—	ASTM D150
Dissipation Factor (at 1 MHz) ¹	0.0026	—	ASTM D150
High Voltage Arc Track Rate ²	4.0	PLC Code	UL 746A
Comparative Tracking Index (UL) ²	1.0	PLC Code	UL 746A
High Amp Arc Ignition (HAI, PLC 0) ²	min. 1.5	mm	UL 746A
Hot-Wire Ignition (HWI, PLC 1) ²	min. 6	mm	UL 746A
Hot-Wire Ignition (HWI, PLC 2) ²	min. 1.5	mm	UL 746A

Table 5 of 7

4 rows

Characteristic	Value	Unit	Method
Izod Impact (Notched, 23°C) ¹	256.0	J/m	ASTM D256
Izod Impact (Notched, -30°C) ¹	90.0	J/m	ASTM D256
Instrumented Dart Impact Energy (at peak, 23°C) ¹	40.0	J	ASTM D3763
Instrumented Dart Impact Energy (at peak, -30°C) ¹	16.0	J	ASTM D3763

Table 6 of 7

14 rows

Characteristic	Value	Unit
Drying Temperature ⁴	75 - 80	°C
Drying Time ⁴	3 - 4	Hrs
Drying Time (Cumulative) ⁴	8.0	Hrs
Maximum Moisture Content ⁴	0.02	%
Melt Temperature ⁴	250 - 275	°C
Nozzle Temperature ⁴	250 - 275	°C
Front - Zone 3 Temperature ⁴	240 - 275	°C
Middle - Zone 2 Temperature ⁴	225 - 270	°C
Rear - Zone 1 Temperature ⁴	215 - 265	°C
Mold Temperature ⁴	55 - 75	°C
Back Pressure ⁴	0.3 - 0.7	MPa
Screw Speed ⁴	20 - 100	rpm

Table 7 of 7